Hello Sir, if you idle standing still with no gear in, and you hear a noice from the rear part of the primary, and this noice disappears when you pull the clutch and put 1st gear in, then it is the inner primary bearing and race which has failed. The remedy is to replace the race and the bearing. I did this on my 2006 FXDL. I also replaced the stock tensioner with the Hayden tensioner. Still it works fine. Good luck!

sounds just like mine!!!! i thought it was my damn adjustable pushrods that i adjusted 9 million times

Had the same noise on my wifes 06 dyna . it was the bolts in the rotor housing ,over the stator. Bad design, Harley changed it in 07 and made it one peace.

I uploaded the Gasket and Seal 🦭 Part numbers for everyone 1994-2006 so you don’t have to chase down part numbers thanks for the helpful video

It's the chain tensioner that chops teeth. the best thing is to weld it on, you still have the suspension.

Mine same noise 02 roadking. Mine is belt drive. Did u fix yours?

Did you ever solve it?

does it stop when u pull the clutch in?

06 didnt have guide pins for inner primary they put them in in 07 I read.

Looks like it’s low on oil!…

@fxrmike5145

2 жыл бұрын

Ha 😄

Look up at the inside of the primary cover and see if your chain has been nicking it as that may account for your metal particles in the oil. On the sportsters and older Evo motors the push block is solid manually adjusted and not automatic so you do not have this problem. See if you can find a manual old style push block to replace your semi auto ratchet version.

All tractors make that noise man!

It,s the Chain tensioner you see That too 1 Click higher

Can you run primary like that without oil ???

Yo corregí un estrepitoso ruido, era el rodamiento del eje principal, estaba machacado, fue en mi RK Classic 2007 model.

Inner primary bearing.

I think this is the noise i have after harley davidson painted my primary..what could of happened..

Sounds like a wicked tight spot on the primary chain .

@brsha8762

Жыл бұрын

Maybe too much crankshaft runout... makes the chain go tight-loose-tight-loose.... etc.

Inner primary bearing it seems. My ‘06 Dyna makes the exact same noise.

@In_His_presence4ever

5 жыл бұрын

I'm about to replace the inner primary & clutch basket inner bearing

@mikeburton1703

3 жыл бұрын

i have some noise when i have the bike in neutral and then it goes away when i pull the clutch in

@smrtrbl86

2 жыл бұрын

Almost looks like the crank bearing. The one so many people replace with a Timken conversion. Looks like the bolt on the front chain drive is wiggling

Clutch hub bearing

Compensator???

Try a thicker Vis oil. Try some GO 90w. Install a new primary chain. Inspect sprocket teeth for wear when installing the new chain.

My stator screws came loose and were hitting the rotor. Sounds just like that.

@seanbinghamvldable

2 жыл бұрын

What year and model bike was that?

@scottberry5266

2 жыл бұрын

@@seanbinghamvldable 1990 Harley 1340 evo.

This is the actual only video I've seen where you show the noise from the primary itself. In my specific case I have a whistling sound when I slow down recently that sounds like a bomb being dropped out of an airplane. It's very faint but you can hear it when the clutch is pulled in and you're coasting up to a stop light

@BDK27970

2 жыл бұрын

Is your belt rubbing on the platic guard somewhere far below?

@thaglove1

Жыл бұрын

Primary to tight

@Kyle-mo7tq

Жыл бұрын

I went on a ride today and I just noticed that's to I thought I was hearing things what's the best way to fix it

Believe the compensator bolt is lose.

The primary chain on vibrating up and down is pulling on the spindle and Let It Go!

Did you find out what the noise is? Thanks

@linnboyd2505

5 жыл бұрын

Not sure. I replaced the slider cam in the compensator (behind the front primary sprocket) and the primary oil (went from Bel Ray to HD Syn3) and it has quieted down. There is still a little noise, but nothing like it was. Comparing the new to old slider cams, the peaks on the old one had about .020 wear. I have the factory exhaust, so I can hear a lot of mechanical noise from the engine. I think this is normal since there are a lot of moving parts. The clacking noise I had was something that got louder over time and it did not sound normal. Probably wouldn't hear it if I had louder pipes though. Thanks, LB

@In_His_presence4ever

5 жыл бұрын

@@linnboyd2505 thank you

@linnboyd2505

4 жыл бұрын

@@carminedeprisco1346 I replaced the slider cam and it seemed to fix the problem. I have since traded it in on another bike. It was still running fine (no clacking noise) when I traded it.

@mikeburton1703

3 жыл бұрын

what a video ....he made us listen and that was it.....come on man...

@linnboyd2505

8 ай бұрын

Yes. I replaced the compensator forged ramp piece and it quiet down. It appeared to be worn. Harley doesn’t offer a replacement part, so I had to buy it after market. I traded this bike in on a Heritage Softail a few years ago. I now have another Super Glide (08 anniversary). I really like the Dynas from this vintage.

That almost sounds like a exhaust leak!!!

Its not oil i checked and oil was full its problem with the engine light and battery light staying on when engine is running and battery light saying not charging but the scraping noise from left side of engine i wont know until my harley Davison shop looks at it and puts it on dionysius computer

Hlo sir I have Harley Davidson please tell me information

Just junk the automatic chain tensioner and replace it with a manually adjustable one

YOu really want to fix it ? I pulled the chain drive out ; and replaced it with a 3 inch belt drive. That was over 10K miles ago, on my 99 twin cam, still works just fine and dandy. Harley will never go with a primary belt drive. They are too robust, and dealers would take a huge hit in "shop income" not fixing primary chain drive problems......

the solution,put it back together and ride the damn thing .you can chase noises all day long and never find anything.except a good case of nervous tension.it's a great product have some faith!!!!!!!!!!!!!!!!!!!!!!!!!!!!!!

Horrible engineering 1 tension shoe ..wth

scrap it and get yourself a mule, the 4 legged kind

what kind of a video was this...you had your head in the way and never told us the problem.....probably wouldn't do me any good to ask you what the cure was.....?

@tyee4u

3 жыл бұрын

Often guys post videos on KZread so they can send a link to a mechanic or something like that, not so much for public to view. KZread just uses their algorithm to suggest it to you.

Orgoglio italiano

Looks like it’s low on oil!…