Never knew these engines could brake. Except the timing chain stretch (bad oil maintenance) never saw one died. 600.000 KM's and still running.

@darrensaward1053

Жыл бұрын

They don't brake, they over heat😂😂

@user-wv6mx8dr1f

5 ай бұрын

I have a N16 with a QG13DE here in the Philippines and already had 600,000km and its great! It's never been overheated once.. the only issue I have now is the valves tickin' maybe because of age..

@abbas431

5 ай бұрын

Is yours a QG18 and did you have your gasket replaced at some point?

very good tutorial, bro

Thanks alot,

Awesome my friend. Could you make a video replacing injectors on this car please? Thanks!

@carfix1993

8 ай бұрын

Ok

Very good, well done. Only thing I think I would have done was to lubricate the cam bearings before putting the caps back on them. Could you use diesel to flush the engine instead of oil, without the plugs in and crank engine with the starter then thoroughly drain and put new oil in then?

Good job. I was worried about the chain dropping but as you explained to others, it is not necessary to hold up the chain... thank you

@carfix1993

Жыл бұрын

Yes it not falling

@738danny

Жыл бұрын

I am starting mine soon your video was very helpful ... wish me luck!

@carfix1993

Жыл бұрын

Good luck 👍

@738danny

Жыл бұрын

Did you use new head bolts?

@carfix1993

Жыл бұрын

Yes

at 10:00 where u are taking off the 2 gears. I need the cut out part on how you loosened the bolts. TYVM.

great video

hi my nissan sentra1.6 is overheating i don't know that its a gasket or themostart

I'm sorry, but what was that that you brushed on the head again? thanks!

Does this car have an O2 sensor i can find mine its the same is the one in the video ?

also how did you turn the engine over? were you just rotating the Crankshaft? and is it suppose to be TDC?

Is it necessary to turn the camshaft 4 times before instal of timing chain ? What if the cam is installed exactly the same way it came out ?😊

What's the tighten spec for the heads bolt

How you get to that dot?

Next time please apply the Shellac sealant on the head gasket, both sides, not on the block.

chain doesn't run from crank gear when let it go?

@carfix1993

2 жыл бұрын

No

Why no lube before installing camshafts?

@JadieFowler

10 күн бұрын

Wouldn’t the oil do that ?

Nice job, I'm going to do same on my QG16, can i know what kind of sealer you use on before putting the gasket. Thank you

@carfix1993

Жыл бұрын

Nissan genuine sealant

@azzeddinefoura4741

3 ай бұрын

Did you replace the head gasket? Is the car doing well with the new head gasket?

And the torques of camshatf caps doesn't matter?

What was your tightening sequence including how tight for the rocket cover? Many thanks

@mpho1247

Жыл бұрын

Manual says: 9 3 1 6 8 7 5 2 4 10 bolts on timing cover 11, 12,13, 14 Stage a: 1-10 = 29 Nm Stage b: 1-10 = 59 Nm Stage c: Slacken off Stage d: 1-10 = 29 Nm Stage e: 1-10 = 50-55 degrees Stage f: bolts on timing cover 11-14 = 6,8 - 8.0 Nm

@azzeddinefoura4741

3 ай бұрын

​@@mpho1247 does every mechanic knows this? Because I took my car to a mechanic and bought a new head gasket to replace the old one and I am worried if he doesn't know the tightnening sequence

@mpho1247

3 ай бұрын

@@azzeddinefoura4741 Hopefully he knows, if not, as long as the gasket won't blow.

Do you have to have the camshaft lobes pointing up or in any specific direction after you install the sprockets? Just wondering if they are suppose to be pointing "up" or if it matters. the camshaft lobes.

@carfix1993

Жыл бұрын

Cam lobs point up means no1 cylinder compression/both valves closed. No I piston TDC

@toddlight3193

Жыл бұрын

@@carfix1993 and is that what your suppose to do? Have them in TDC?

@carfix1993

Жыл бұрын

Yes

Does any one knows what size is the hexagon key for the head bolts??

@carfix1993

3 ай бұрын

12

What about crank bush ????? It will not work long because when changed the ring and piston we need work behind force come from crank ….. now compressor will be high and crank with old bush .

I drive a Nissan Almera Classic with the QG16DE engine that looks similar to the QG18DE, I forgot to close the radiator cap which led to alot of coolant loss which caused overheating and that led to a blown head gasket, I am gonna replace the head gasket tomorrow and I just wanna know if I can still drive it as hard as I used to before? The car was driven for 78k miles, will the car be the same as before blowing the original head gasket ? Will I be able to push the car to its limits after the head gasket replacement just like I used to before or not?

@linetakinyi7229

2 ай бұрын

Mine too..I'm soo worried

@azzeddinefoura4741

2 ай бұрын

@linetakinyi7229 don't worry, I replaced the head gasket and it is running as good as it used to before, nothing serious bro it is just a head gasket.

When you let the chain loose, did not lost the right timing?

@shivabhagwandeen4643

Жыл бұрын

No it won't because the timing over have an lip preventing the chain from dropping

@Bengal..

Жыл бұрын

@@shivabhagwandeen4643 I washed 2 other videos they both said you have to hold the chain in place otherwise you'll loose the timing and they were wrong, until I watched your video, I when and did this job by my self with out any fear of messing up the timing thanks

Common problem using oil

101018m027 is that the part number of the gaskets?

@carfix1993

Жыл бұрын

I will let you know

Здравствуйте, интересует чем вы смазывали прокладку ГБЦ?