Realmente hiciste un buen trabajo. Disfrute mucho viéndote saludos desde Argentina.

@maxautouk

8 ай бұрын

Thanks 🎉👍🏽

Fantastic job lad but you need to get one with doing the clutch and the seals etc that would have been a great part 2

@maxautouk

3 ай бұрын

Aye it would have been thanks for the comment

Thanks for video i removed today the same gearbox.

@maxautouk

4 ай бұрын

Glad the video helped! Hope you got on ok 👌🏽

Thank you for this video. It helped me alot as I needed to change clutch and flywheel

@maxautouk

7 ай бұрын

I’m glad the video was helpful and thanks for the comment!

Great video! This will help alot! Thank you very much 🙏

@maxautouk

3 ай бұрын

Glad it helped!

Max I really enjoyed the way you tackled this one.With your Video on the Micra K11 I was able to replace the Clutch on my car .That video was SO helpfull I thank you for giving me the confidence to do it. I have just ordered a Cordless impact wrench basic model chinese knock off for future projects.Can you tell me if the one you have is an adjustable torque type? I ask because I don't think the one I ordered is.I've never used one before and I am a little worried if the torque,rated at 420 NM is going to be safe to use on suspension bolts etc without snapping any bolts? Also would it be OK to tighten the bolts when they go back in with the Impact.Can the torque be varied on the cheaper versions by feathering the trigger ?I would welcome your advice before I undertake any more "ambitious" projects .Best Wishes always look forward to your uploads.M

@maxautouk

11 ай бұрын

Hi Mark good to hear from you Impacts are best used for loosening, I tend to use mine for tightening a little but I always leave them sort of loose and tighten them up by hand and torque them down properly with a torque wrench!

Great video! What is the tightening torque for de driveshaft nuts?

@maxautouk

5 ай бұрын

Hi there, it is 280nm!

I’m struggling here, there doesn’t appear to be enough room between the gearbox and the subframe. How do I achieve enough clearance ? The gearbox is hanging on just the one engine mount and all ready to drop barring the bell housing bolts. Any help appreciated..

@maxautouk

2 ай бұрын

Pry bar and force it out 😄 it is tight

@MytubeSPY

2 ай бұрын

Ok, I’ll try, not sure how I’ll get it back in though 😂 I’m removing it to do the RMS. Thanks for the video though, it’s certainly helped me get this far.

Very helpful thanks

@maxautouk

8 ай бұрын

Thanks very much

Did you replace gearbox or only the clutch and flywheel.

@maxautouk

4 ай бұрын

I just had a bad leak from the rear main seal and since it only takes half a day to do the entire thing I didn’t fit a new gearbox or clutch - but clutch and flywheel wouldn’t be a bad idea

Hello mate, where are you based? I’ve broken down I’ve got the exact same van, colour and year.

@maxautouk

5 ай бұрын

I am currently based in County Fermanagh in Ireland! Are you mainland UK?

@hermon9278

5 ай бұрын

Yes unfortunately.

@maxautouk

5 ай бұрын

@@hermon9278 what’s happened to your van?

Hey is there a video with it being replaced and going back in

@usfiveandronniethecamper

Ай бұрын

Having trouble myself getting it back in doesnt seem to want to go in

@maxautouk

Ай бұрын

The rear end of the gearbox will hit the subframe, you need to moge yhe engine forward to get it to clear and the differential needs to go in the upwards position… sadly i didnt film refitting but i need to do the clutch soon so there will be a video eventually…

Did u chock the back wheels

@maxautouk

8 ай бұрын

Nope I didn’t chock the rear wheels

c'est faux metter la cle a choc sur l'ecrou pas sur le premier boulon de la fusée pour ne pas endomager les dent de boulon