I've just discovered your channel and I'd like to say people like you are greatly appreciated out there for experimenting and sharing their work, great job and thank you.

I did electronics at school, but failed miserably... I love your genius invention, for years people have been duped to believe there is no such thing as perpetual motion that can be used to power itself and other devices. You are a genius brother

@EnterTheRealm

2 жыл бұрын

Thanks bro. 😊

@boshaveit

2 жыл бұрын

@@EnterTheRealm credit where credit is due bro.

Really cool and love DIY builds - nicely done!

@EnterTheRealm

2 жыл бұрын

Thank you very much :). 😊

Oh, it lights the light bulb. I thought maybe we were going back in time to 1965! Interesting. Thanks for sharing

@EnterTheRealm

2 жыл бұрын

Haha brilliant yeah. You're welcome.

Love the accent too

I'm off the grid and doing it as my highlander family did. ROUGH . This is so cool. But it's all gobbledegook to me. Canny we Scot.

Fantastic work my friend!!

@EnterTheRealm

6 ай бұрын

Thank you, hope it helps 😊

Is it possible to get a small schematic for the driving power for the direct drive motor. I have difficult spinning it with alternator and it get very hot and slows down when you put load on it. Need just a sketch of power in to the transistor amd the connection and where to tap for back EMF and where to dump it.

Looks like a 36 coil washer motor. This is an inverter so input power is DC and output is AC. Looks like the capacitor bank is the main load. The transistor drives one set of coils to get it spinning and then you pull the power out on another set. Interesting application. Might want to be careful of inadvertent electrocution. Those are some pretty significant voltages.

@EnterTheRealm

6 ай бұрын

Thank you for the kind words of advice.

Hello. Very nice job. I want to try it, I just don’t see the drawing and the type of parts well. What part are the bulb and coil circle, diode? Are the coils connected in series per phase? You can send a visible drawing? Thanks.

Do. Just to clarify. The coils are wired in parallel per phase? Or in series Could? Could we see the rear? Excellent work BTW.

@EnterTheRealm

2 жыл бұрын

John, of course you can. The coils are wound in series as they were done in the factory. Only one phase is needed to make it turn so 12 coils in series every third leg.. and thank you much appreciated

Liam..... I spent 4000 for solar for my community 😣 for power. I REALLY NEED YOUR HELP . I HOPE YOU CAN JOIN US. you are so smart. .

Hi there, What power source are you using to turn it please? Great work and thanks for sharing.

@EnterTheRealm

2 жыл бұрын

You can use any dc source. I have even used a dc motor in reverse too power the hyperdrive with my circuit. And thank you im glad you like it. 👍

@andrewthuku2638

13 күн бұрын

​@@EnterTheRealm Great job. You exit me coz I am trying to do the same but could not find a way to run it so I spin it with alternator but alternator sucks a lot of power and heats up quick. A small schematic diagram just for control for the motor.

Thank you sharing your work, I'm curious what kind of transistor you are using? PNP? NPN??

@EnterTheRealm

2 жыл бұрын

You can use either. However in this scheme its NPN. For PNP just reverse the Polarity of the inputs.

@novalight8325

2 жыл бұрын

Thank you for answering my question. I do have another, in the video you show the light bulb , now I'm assuming this is powered by the initial 130 volt input? or is it the BEMF that is powering it, in conjunction with the diode (full wave rectifier??

@EnterTheRealm

2 жыл бұрын

@@novalight8325 indeed its back emf powering the bulb as only one side of the supply is connected to it. I may make a video showing this.

@novalight8325

2 жыл бұрын

@@EnterTheRealm Thank you, you have been an inspiration. This is an exciting journey to embark on😁

@EnterTheRealm

2 жыл бұрын

You are most welcome. Thank you. 😊

Please help! I don't speak the language, I use google translate. What kind of capacitor do you use, what is it in? Did you change the thread speed for coil C1? I used the factory 12 coils for c1. I used a dc 220uf 400v capacitor. Did not work. The engine started but after 10 seconds the mosfet broke down, type CS20N50. C2 =10 turns were used in 12 coils in series. What did I do wrong?

@EnterTheRealm

2 жыл бұрын

Use a ac 8nf 400v cap where the dc one is and use 100w or 60w bulb accross the cap. How much input voltage did you use? Try a 1200v igbt. You can get some on ebay for a couple of quid. Hope that helps I'm working on new schematic so I would hold off for a little while unless you want to experiment. Also I now have a resistor and inductor on the gate to help with spikes. I did not change the coil ony the amount of turns on c2 but there's another way that'd better. Don't unwind c2 just get another copper wire and wind over the top of c2 for a total of 4 coils.

@EnterTheRealm

2 жыл бұрын

Basically the bulb protects the transistor.

@EnterTheRealm

2 жыл бұрын

10 secs is good for first try trust me. Well done.

@llcd4992

2 жыл бұрын

@@EnterTheRealm Thanks, you helped a lot. I used 8 car batteries connected in series. I did not use a base resistor. I thought I'd put a 100 ohm or a potentiometer in it. I'll put up a video when the engine starts. A detailed circuit diagram would help a lot. Thanks

@EnterTheRealm

2 жыл бұрын

C2 do only 10 turns now but just over lap the existing c2.

From what I can see it loads to a certain point and then whatever you add load wise the input doesn't seem to change. Am I correct?

@EnterTheRealm

6 ай бұрын

Yes you are correct mostly lol, the input stays roughly the same. Its why I said its more voltage dependent. Doesn't want to consume more than a certain amperage due to ohms law.

@johnkoury1116

6 ай бұрын

@@EnterTheRealm ahhhh...thank you.

@EnterTheRealm

6 ай бұрын

@@johnkoury1116 no problem merry Christmas bro

BTW, Could you please confirm that your transistor is it PNP type? I can confirm that 12v is not enough to have the system started/running. What's your minimum voltage to have it spinning ? Thx!

@EnterTheRealm

2 жыл бұрын

I'm using igbt npn type min voltage with 10 turns on each leg for the gate is around 180v to start by hand. Or less if you start with a drill.

@felixbourque

2 жыл бұрын

@@EnterTheRealm i will try that thx

@EnterTheRealm

2 жыл бұрын

@@felixbourque try reversing the power coil polarity if you get nothing.

@EnterTheRealm

2 жыл бұрын

Do n you have Skype or fb?

@felixbourque

2 жыл бұрын

@@EnterTheRealm sent you an invitation and PM on FB. See you there buddy

How to repair

Interesting stuf , what fb page are you on i like to be a member to

@EnterTheRealm

2 жыл бұрын

I'm on quite a few fb pages.

@oscarverwey

2 жыл бұрын

@@EnterTheRealm sorry of i was not precies , i mean the experimental alternatieve energy related page

@EnterTheRealm

2 жыл бұрын

I'm on most of them. Try searching that exact term it's likely I'm already a member of all the groups you can find.

@oscarverwey

2 жыл бұрын

@@EnterTheRealm oke Thanx i Will, can you name one you think is the best

@EnterTheRealm

2 жыл бұрын

@@oscarverwey if I had too say then maybe this one facebook.com/groups/246767748854856/?ref=share I really like the guys over here but the akula group is also okay.

what is intersting the output do not make the input current go up by a lot

@EnterTheRealm

2 жыл бұрын

Agreed.

@EnergySeeker

2 жыл бұрын

@@EnterTheRealm what was the reason you reduced the C2 amount of turns ? what was the rating for the mosfet you used ? , we can use a mosfet which can take 1200 volts even ,

@EnterTheRealm

2 жыл бұрын

@@EnergySeeker too stop the transistor burning. C2 is now a fourth coil of separate wire wound on top of the factory windings. But following the same path .

@EnergySeeker

2 жыл бұрын

@@EnterTheRealm because the gate voltage is low that what you mean from 20 to 30 volts max , but we can pulse it external and use that coil , what is the idea to have the gate pulsed by that 10 wire coil , cant we pulse it from outside ? 50hz or 60hz ?

@EnterTheRealm

2 жыл бұрын

You can try but is a self oscillatory system.

We need you to electric our community. Please come visit and help

@EnterTheRealm

2 жыл бұрын

I would love too, maybe In the future I could but not at the moment it wouldn't be possible. I'm sorry.

and what does it do / is so cool about it ?

@EnterTheRealm

2 жыл бұрын

Nothing, I don't even know why you would watch such a video.

@solunasunrise

2 жыл бұрын

@@EnterTheRealm and why did you build it then ? wehn i build stuff i always have an intention behind it !

@solunasunrise

2 жыл бұрын

@@EnterTheRealm because i m running a free energy / overunity group and site on FB and i m always on the lookout for something worth to show around !

@EnterTheRealm

2 жыл бұрын

The intention is too have a pure sinewave capable of doing work, from a dc source.

@EnterTheRealm

2 жыл бұрын

The next stage is too loop.

Waist of time..just like gerald morin setup..you show a clasic generator drawing more amps as you load it and boging down

@EnterTheRealm

2 жыл бұрын

Glad you enjoyed the video.

which topic in PJ's book you referred to one of the comment below. Thanks.