Just used the crank holder I bought from you a year or so ago and it worked like a champ. Thanks Andy

You are the man! Ove seen a lot of videos and you are by far the most detailed!!!! You take the time to explain what and why you're doing something!!! That's huge!!!!!

BTW, i found the torque spec for the oil pump cover screws, its in the toyota 1FZ/1FZFE RM321E shop manual, section "Engine -Lubrication System", "Oil pump cover x oil pump 10Nm / 105kgf-cm / 8 ft-lb "

Hi, your videos and tutorials help me save alot of time and money working on my 95 TLC. This video solved my oil leak coming from the front crank seal. Hats off to you and thank you so much 👍👍

Thanks a million for these videos, you walked me through the entire job on my 93. Seeing it done and hearing tips from guys who actually work on them is worth a thousand shop manuals. Your explanations are excellent, and the narration is relevant. My main pet peeves with other videos.

I just ordered the seals for this job along with the water pump/rad hoses. I'll be ordering the crank holder tool from you; definitely looks worth it! Thanks for all the great videos!

Super informative video! I watched this and performed this today and everything went just fine. The best trick you mentioned was using a hammer to hammer in a #3 phillips-head. Got those oil pump screws out with no issue! I also bought a used crankshaft bolt holder tool off of Ebay and just realized now that it is the exact one that you're selling! I got that bolt off by using a long metal bar on top of the breaker bar. Very happy right now that I no longer have a massive oil leak. The bottom of the oil pump o ring ripped so I was losing about 1 quart every 50 miles!

The torque value for the bolts holding the oil pump cover should be 8ft.lbs. So states volume 2, page LU-4 of the '97 1FZ-FE Repair Manual. Thanks much for the in depth vids, extremely helpful.

@OTRAMM

5 жыл бұрын

Awesome, Thanks. We've got the online version of the manual and it doesn't show the torque spec. Much appreciated.

Attempting this tomorrow! Nice quality video. Thanks!

Ingenious tool design! Good video, thanks.

You are the absolute best! And saved me thousands with these videos!

You’re videos are great, Ryan. Thank you for sharing your knowledge.

Fantastic video! I'm about to do this on a 97 and this was very useful to see where everything is . Great video! Subscribed!

I finally did this job, thanks for the video, worth well more than my (small) Patreon donations! I couldn’t locate a nearby torque wrench rental with that much torque, but worked around with a torque adaptor and a 3/4” breaker bar extended with a couple feet of 1” black pipe (and careful placement of my forehead in case something let go).

Great video! Filled with lots of great tips. Thanks!

This is a great video thank you for taking the time to do it

Another great video, thank you so much.

These are so appreciated

Thanks for the info. Very useful

Awesome video. You guys should do an 80 Series head gasket replacement video now!

@OTRAMM

6 жыл бұрын

I've considered it, but man that would be a long video :)

@abhitchc1106

6 жыл бұрын

OTRAMM but it would be nightly nice to have a high quality video when searching for one. :)

@harleyd301

4 жыл бұрын

He did one

Awesome video!! Guess I will be doing this sooner than later...or not! haha

Great video!!!

@OTRAMM

6 жыл бұрын

Thanks

Great vid , I need to do this on my 2re fz Tacoma 1995 , not sure if it has a main seal but I’m going to see I have a oil leak on the oil pump, I see no videos on KZread so this helped

Well done

thank you nice video

Do you use the Toyota seal packing 103 for the seal?

i tried to do this 3 years ago... the car has not moved since :)

interesting, mine has a rather large oil leak from the front cover around that location, although every other 1FZ i've seen is dry in that area

If only doing it was as easy as watching it, but yeah great video.

I wish and want this guy to work on my 80s series...soooo efficient! Too bad I'm in Chicago area😔😔

Hi, I searched all thw coments and read the discription and couldnt find a link to the guy selling new screw for the oil pump cover and you lentioned they sell heater hose or vacume line kits but i couldnt understand from the audio in the video. Is it possible for you to send a link? thanks!

You have become my new favorite TLC mechanic, I have a 96 and it needs to have the fender flares removed and new trim seals put on, if you have an idea of a good video for that please post. Thx. M

@OTRAMM

5 жыл бұрын

I absolutely hate doing the fender trim. I worked for a body shop years ago and had to do them all the time. Haven't done one since 😁. We don't do any body repair at the shop so we don't ever get in to pulling the flares.

Thanks for the video, very helpful and hoping the pulley holder comes back soon! Your videos made me much more comfortable working on my LC and its been awesome doing so. Have you discovered any other methods to hold that pulley by chance?

@OTRAMM

Жыл бұрын

We stopped the entire manufacturing side of the business. I don't think we'll be starting it up again. There was a guy on Ih8mud that was making a similar holder.

Thanks for the awesome video. Can you give some tips on priming the oil pump. I have the engine disassembled currently. I’ve read that some people like to pack the oil pump cavity with petroleum jelly or white lithium grease. Or is the .9 cu in of oil applied into the oil pump per FSM sufficient? Do I apply assembly lube around the lobes of the rotor first then pack it? Thanks

@OTRAMM

4 жыл бұрын

I think the oil the fsm calls for is to prime it. I leave the ignition coil and fuel pump relay unplugged and crank the engine for a bit to get oil pumping before we actually start it.

What fell off when you pulled out the oil pump cover?

Hi Buddy...my 96 FJ80 makes a rattle noise when start...after being off for a week....the rattle noise last 1 or maybe 2 seconds Thanks a lot

Question on when u put the radiator back in. The foam sealing strip on the bottom of my radiator disintegrated when I touched it so I need to replace it. Can you explain what foam stuffing (or whatever it’s called) you put around the radiator to air seal the radiator? I did not have any foam sealing the shroud to the back of the radiator but maybe I need foam sealing there too? Just want to make sure I have optimal air flow thru the radiator. Thanks for any tips you might have. Love your videos!!!

@OTRAMM

4 жыл бұрын

We've never bothered with replacing the foam. It's missing on most we see without any noticeable detriment.

Tried to order the pulley tool...sold out so looking forward to your next batch! Two quick questions...when you took the radiator out I assume you drained it first? And when you put the belts back on do you have to adjust any type of timing or tension? Thanks is it mark? Your name?

@OTRAMM

5 жыл бұрын

Yep, drained the radiator first. You need to adjust the belts when you reinstall them. The next batch of pulley tools should be here in a day or two. If you want shoot me an email to otramm@otramm.com and I'll put you on the list. And I always forget to introduce myself on videos. I'm Ryan

Another question, when you have all your belts off and just the pulley exposed would it be harmful to also steam clean the front part of the motor? Mine has the o ring dripping so there is a good amount of old oil sitting on it. Just don't want to harm anything

@OTRAMM

5 жыл бұрын

As long as your'e careful it should be fine. Just don't spray directly at the intake ports or electronics.

Thank you for the videos! As a new 80 owner, these are incredibly helpful! So... say I were to drop the key into the timing cover. Or in this case a nut (from the open valve cover up top)... What's the best way to get it out? Magnet fishing has thus far been unproductive. I also pulled the easy-to-reach oil pan on the bottom to go in from that side. The crank rotates and doesn't seem to bind, but it still makes me uneasy having a nut floating around in that area.

@OTRAMM

Жыл бұрын

There's not a real good way to get in there short of pulling the timing cover, which also means pulling the head.

@austencam

Жыл бұрын

​@@OTRAMM Thank you so much for the reply. I feared that would be the case... well this just turned into one painful valve cover gasket job.🤦‍♂

Are you kidding? Yes very helpful thanks again it's better to learn from someone that takes the time than to read the repair manual. At least that's how I like learn. Can I borrow that crank shaft pulley stop tool?🤣

Ryan, since I will be this deep into Changing the o ring for the oil pump...would you suggest just changed going the entire pump? Is it that much more labor to do so?

@OTRAMM

5 жыл бұрын

The oil pump is built in to the timing cover so you'd be replacing the entire cover. It's a huge job with the head and oil pans coming off. It's a ton more labor to get the pump changed.

@JoonRhee

5 жыл бұрын

@@OTRAMM darn! I was hoping it wasn't but fair enough. The o ring it is! Thanks

Another awesome video, thanks! I like the hood mounted light, looks like it's a plug in? Which one are you using? I looked on your tool link but didn't see it

@OTRAMM

5 жыл бұрын

It's a Matco light. It's pretty old. It's from before everything went to LED and cordless. It still works though.

@BillyGoatsAdventures

5 жыл бұрын

@@OTRAMM thanks, I have been looking for a corded led, I might just have to have battery faith....

Ryan Got the pulley tool today! Super pumped to use it. Quick question again, is that crankshaft seal the rear seal or the front seal? I can't figure out which one to purchase. Thanks

@OTRAMM

5 жыл бұрын

Front seal, I think Toyota calls it the timing cover seal.

@JoonRhee

5 жыл бұрын

@@OTRAMM thanks Ryan!

Will the keyway always be on top as shown in the video or is there a mark on the pulley to align so it is on top when I pull the pulley off?

@OTRAMM

2 жыл бұрын

It spins so it won't always be facing up. I'm pretty sure it's facing down at 0 on the timing mark. I've never paid a ton of attention though. I don't line anything up specifically before pulling it.

I love you man. In all seriousness...love these videos. Quick question...do you happen to have a cut sheet or dimensions to Fab up one of those pulley bars? That would be epic thanks a ton! Love your work and look forward to more and doing this myself this summer

@OTRAMM

5 жыл бұрын

I actually sell them on our website. There's a few left from the current batch and more on the way. www.otramm.com/1fz-fe-crank-holding-tool.html

@JoonRhee

5 жыл бұрын

@@OTRAMM amazing! You. Da. Man. Saving lives

@JoonRhee

5 жыл бұрын

I just checked em out! Love the update...I was really hoping though they looked like the old school iron worker kind you have! But haha I may have to settle for the "new kind"

@OTRAMM

5 жыл бұрын

The new style is actually stronger and easier to use. And it even fits in a flat rate box :) I've switched over using the new one. Kept one out of the first batch for myself.

Another awesome video 👌 When I change the o-ring can I slip out the oil pump star assembly and replace them both easily?

@OTRAMM

4 жыл бұрын

They slide out but there isn't usually any reason to replace them.

@BillyGoatsAdventures

4 жыл бұрын

@@OTRAMM ok thanks, just figured with a router set only running about twenty bucks, would be good preventative maintenance and cheap insurance. Are you still doing the weekly web chat?

Can you do a video on a 200 series radiator replacement since they are cracking and leaking, also a 200 series starter replacement. Good Video, thanks

@OTRAMM

5 жыл бұрын

Wrote an estimate Friday for a 200 radiator so should have one coming in soon. Haven't had call to do a starter on one yet.

@abhitchc1106

4 жыл бұрын

Have fun doing the starter. When I replaced mine on my 200, I had to remove the exhaust manifold first. A few of those bolts were a huge pain.

What size bolts go into the balancer pulley that hold your tool in place? M8? what thread?

@OTRAMM

2 жыл бұрын

M8 1.25 I think

At about 30:50 you talk about how you washed the front of the engine. Do you have a video on how you did it correctly?

@OTRAMM

2 жыл бұрын

No video, just degreaser and a power washer. Just don't shoot directly at electrical bits and seals.

Such a great video ......Thank You Sir .....jusr curious what is the in your shop cost of doing the job?....CHeers

@OTRAMM

3 жыл бұрын

Depends on the add ons but the base job is around 850.00

What size bolts you use to hold on that custom tool for the crank pulley.

@OTRAMM

2 жыл бұрын

M8x1.25 if I recall correctly.

Very good job, excelent Can you draw and put in a file or pdf document the tool to hold the puller? I want to do in my 1996 Land Cruiser. One guy in youtube do the same job but he hold the crankshaft in the back the engine, in the hole of the flywheel put a socket, what do you think? its safe? or can do some damage? Thanks some much for your videos, I enjoy every one of your videos

@OTRAMM

6 жыл бұрын

I've seen folks do the socket trick. I've always worried about it bending the flex plate. I'll see if I can dig up the drawings on the holding tool. Glad you like the videos.

@OTRAMM

6 жыл бұрын

Well if you're a fan of losing teeth.... That works for loosening but not tightening. Oh I think I figured out how to fix your video. I had to do a similar fix on this one. Just gotta wait til Crash gets back from paternity leave :)

@jailbreakoverlander

6 жыл бұрын

my tetth were no where near the underside of the frame you method is great but the other worked perfect. and my 350lb torque wrench tightened it right up I need to bring mine in for a bit of exhaust mod dont want anyone else touching your pipe.

How can I get a counter brace for the removal and installation of the harmonic balancer bolt... great video. 👍.....

@OTRAMM

Жыл бұрын

I don't know if anyone is currently making them.

@dfox344

Жыл бұрын

@OTRAMM Thank you for your reply

Can you tell me what impact wrench/tool you used, or anyone used? I can't the screws on the pump cover to move. Though I am using a ridgid screw impact driver.

@OTRAMM

Жыл бұрын

It's a Milwaukee 3/8 impact. Gotta be careful though itll strip them without a good jis 3 but

@dave2574

Жыл бұрын

@@OTRAMM Thank you. And thank you for the video! You are so right! The right bit and lots of hammering, and a couple days got them out. One one stripped.

Hi I’ve just rebuilt my 1fzfe but I have no oil pressure how do I gain oil pressure any information would be great thanks

@OTRAMM

3 жыл бұрын

No oil pressure on the dash or no oil pressure with a mechanical gauge? First thing I'd check is the wiring at the gauge sender if it's no pressure on the dash. It's down behind the AC compressor. If no pressure on a mechanical gauge make sure the crank bolt is torqued properly.

@tonysullivan5442

3 жыл бұрын

@@OTRAMM hi yes on the dash it’s not showing pressure my sender is new will check crank pully tomorrow morning can I take plugs out plus pull off oil filter put a little grease over the filter hole refit filter disconnect coil lead n turn the motor over slowly will that do it

@OTRAMM

3 жыл бұрын

@@tonysullivan5442 putting grease in the filter won't do anything. When the engine was assembled was oil added to the pump when it was put together? I'd use a mechanical gauge to see exactly what's going on.

Great video. How about a valve stem seal change without removing the head video 🤔

@OTRAMM

5 жыл бұрын

That won't be a video I'll be making :) Those stem seals are hard enough to deal with when the head is off. Trying to do them in the truck and not drop the valves in would be a nightmare.

@1mach28914u1

5 жыл бұрын

OTRAMM That’s probably why I’m just putting an additive in the oil for now. 😩. But I’ve started doing those two oil seals. Mines a 105/100 series 1998 but very similar. Thanks again for making the video.

How many hours labor would a traditional shop charge for this? 2 hours worth?

@OTRAMM

4 жыл бұрын

I think book rate is around 6 hours

If your car is a Manual would you even need to hold as you could leave it in gear with someone holding there foot on the break?

@OTRAMM

5 жыл бұрын

I don't know, we only got automatics. It's 306 foot pounds and likely more to break free so I'd doubt it.

@191kieran191

5 жыл бұрын

OTRAMM hey mate just to Let you know I followed your video mate you are a legend this was such an easy job with your way on showing and explaining Only thing I did different was I used the bump the starter method to crack the bolt. How ever I have a manual transmission and putting it in 5th gear with hand break on and something pushing breaks down I was able to Torque the 30mm Harmonic Balancer bolt to spec. HUGE thanks man keep it up

@aGyngaGamer

2 жыл бұрын

2 years late, but yes you can. Don't even need someone to hold the brake, just put it in 4th and chock the wheels

When will your crank holder tool.be available again?

@OTRAMM

4 жыл бұрын

Hopefully within a few weeks. Waiting on the next batch from water jet.

@crishawn1000

4 жыл бұрын

@@OTRAMM how can I pre-order or get on waiting list?

@OTRAMM

4 жыл бұрын

@@crishawn1000 shoot me an email to OTRAMM@otramm.com and I can let you know when they're ready.

The oil pump cover screws are JIS......do you hammer in JIS #3 or Regular Phillips #3 bit??

@OTRAMM

10 ай бұрын

JIS bits. The hammering isn't to seat the bit as much as it is to shock the threads loose.

@ggergg6423

10 ай бұрын

@@OTRAMM Thanks, I have been waiting to do this job, your vids will certainly help a lot.

@ggergg6423

10 ай бұрын

Do you still sell the crank holder tool?@@OTRAMM

@OTRAMM

10 ай бұрын

@@ggergg6423 nope, we stopped making them a couple years ago.

@ggergg6423

10 ай бұрын

Thanks, I will weld one up then. The 308 ft lb torque wrench required almost makes it worth paying someone else to do this job.@@OTRAMM

What size socket do I need for that crank bolt?

@OTRAMM

2 жыл бұрын

30mm

@cmoore555

2 жыл бұрын

@@OTRAMM thank you, somehow missed that in the video. Purchased the adapter plate and can’t wait to get started on this job. Thank you

Just did mine and someone also put a 13mm on my fan as well… weird

I guess it went over 1,000,000+ mile? we all know Toyota engine last longer then its owner lol

What’s the bill to have your shop do this?

@OTRAMM

3 жыл бұрын

Right about 800.00

Hi my friend do have a video changing the power steering pump

@OTRAMM

3 жыл бұрын

I don't, sorry.

@arielmarin6968

3 жыл бұрын

Thanks from Houston Texas

Can you just break the pulley bolt off with a impact??

@OTRAMM

2 жыл бұрын

Maybe, depending on how strong your impact is. You'll still need a way to hold the pulley when you torque the bolt going back on.

@acexayaphet786

2 жыл бұрын

@@OTRAMM thank you for the reply. I just now order a tool for it I saw online. Hopefully this works.

Are you still selling the crank pulley holder tool?

@OTRAMM

2 жыл бұрын

Not currently. The prices for the blanks went way up and made them waaay too expensive to produce. I may find a different laser cutter in the future, but they're on the back burner right now.

@SEEKANDDESTROY717

2 жыл бұрын

@@OTRAMM that's why I asked, I can produce them. I'll reach out via email

I’m betting that an ARB bull bar and a 2.5” lift makes this whole process more difficult.

@OTRAMM

4 жыл бұрын

Not too much harder. Just longer to lean over😁

Esta bien como se cambia una bomba o cualquier trabajo que hace, pero NO ENFOCA O NO SE VE Lo que está haciendo, la mayoría de los trabajos se enfoca la espalda y no se ven los pernos que está sacando, en la instalación del turbo no se ve la conexión de las cañerías de aceite y termina y ni siquiera lo prende.

how to remove stripped screws

@OTRAMM

Жыл бұрын

I usually weld a nut to them. A left handed drill bit works well also

👍👍👍👍👍. По русскому языку!!!!!!!!

Dear All, No mechanics here in Bosnia can help me with adjusting my valves on FZJ80 (one of few if not the only fzj80 here) They do not have tools no shims and no experience with this particular problem. What can I do about it. I would buy on-line tools and shims or adjusting valves kit for the in-line 6, 1fz-fe engine. If there is such thing. Can you tell me what to buy and where? Or you have some other advice. Thanks in advance. www.toyodiy.com/parts/q?vin=Fzj800154193 This is my friend who needs help.

@OTRAMM

5 жыл бұрын

It's rare to need to adjust the valves on a 1fz unless someone has gotten them out of order in the past. As far as I know, Toyota is the only source for the shims. There are a bunch of them so a kit is unlikely. You've got to measure the clearance, measure the shim, and them compare that to a table to find the proper shim thickness. It's a tedious job,.

@mcfobossan

5 жыл бұрын

"OEM Genuine SST Valve Adjustment Tool For Toyota Diesel Engines" Is it the same tool for diesel and petrol valves?

@OTRAMM

5 жыл бұрын

@@mcfobossan I don't know, we never got Diesel trucks here. I've used the SP tools' valve tool. If you have several out of spec it's easier to remove the cams.

Hey brother. I don't understand what the need is for the special tool you made for the crank balancer. Whether taking the bolt off or putting it back on, doesn't the bolt loosen and/or tighten back on simply using an impact?? Even if the balancer spins while taking off bolt with impact or spins while tightening back on, aren't you still loosening or tightening as needed?? Thanks for any info because I'm about to do this exact job on my 95 LC and really wondering if I really need this special made tool of yours. Thanks brother for great teaching video. Subscribed!

@Emayarceeo

5 ай бұрын

How did you get on mate?