1993 Johnson Evinrude 40 HP - Gearcase Service
1989-2005 40/48/50 Pump kit: ebay.to/2kLFjML
Waterpump Chart: everythingoutboards.com/brp/wa...
Molly lube: ebay.to/2lNfxIc
Gasket Compound: amzn.to/34N0wbt
3m 847: amzn.to/2ZY0cYy
Soap: amzn.to/2O3eKPh
Tap Sockets: amzn.to/2Lvyfyi
Gearcase Oil: amzn.to/2LKJcuQ
Пікірлер: 52
Awesome channel man! Working on a 1954 5.5 CD-11 myself. Good luck!
Just realizes that your audio is either recorded or post produced in panoramic stereo... Nice touch.
Thanks so much, this definitely gave me the confidence to tackle this on my new to me boat. 96 Johnson 40hp, should be bout the same. Thanks again
Glad I watched this I have the same motor waiting on my water pump to arrive. Thks for the info I will use it.
This was a great video. Just finished mine.
I also just did this to mine this past spring. Used your previous video for reference. Soon I will need to reseal my lower. I'm starting to get a little water in my gear lube. Not to bad just yet. I would like to see a video showing the differences between the 40 48 50 & 55. Maybe converting a 40 to a 50.
Those 3 screws that hold on the side cover on are a real pain yo get out .but gives real good access to shift rod screw,well worth taking cover off.in process install new pump haven't tried to put side cover back on. Wish me luck!
Great tutorial. I just want to add that make sure you dont twist that shift rod in or out while changing the water pump or else the damn thing wont shift into either reverse or forward, depending on which way to twist it. Ask me how i know lol. I literally just changed the pump on my father-in-laws 1990 40HP evinrude. I guess they make a special tool that has a hole on the end where you can put the shift rod bolt on one end and then sit it on the housing of the bottom end which shows exactly how long that rod needs to be. Well I tried to make a DIY one based on some measurements using a yard stick. It didnt work too well. Ended up just guessing, putting it back together and having to take it apart a couple more times until I got it right.
@chrisbarnett1429
Жыл бұрын
do you happen to know what that tool is to figure out placement? or what to do? i think i ran into the same issue with the same motor. Stuck on what to do
Had an idea. Putting a zip tie on the impeller, bending the paddles, would make sliding the pump housing over it easy.
@andyc8225
Жыл бұрын
I tried that last weekend because I saw your comment awhile ago and thought it was a good idea but it doesn’t work as well as you might think
hey brandon, looks like your gear oil was a little milky, mine was the same colour the other day when i changed it. Did you change your seals right away or did you think it wasnt that bad. I'm a bit concerned that it will do some damage to mine.
Any chance you have a video taking this lower unit all apart? 40HP 1999 Forward reverse gears etc...? Thanks your videos are a big help.
You need to make sure lower O ring is seated properly in the impeller. If not it will break and you'll be doing the job again. It's the O ring that is by the impeller key. You can't just slide it in and think it will seat properly.
Hello Brandon, I have a 97 2 stroke 40hp evinrude, where can I find a jet drive for this as I am traveling up and down the Des Moines river and it does get shallow. Is it a viable and cost effective procedure? The lower unit and prop need replacing already. Any help or advice on where to look would be greatly appreciated! Thanks.
So, I did a full seal kit on my 40 Johnson. Exactly like you did in the video. Put it together and the gears aren’t engaging correctly. Didn’t miss any parts only thrust washer bearing gear and bearing carriage. Matches service manual parts. Do I need to get that bearing carrier in there further? With that special tool hammer? Do I need to seat the gear in there better? Thanks. House looks great! Keep up the videos.
@BrandonsGarage
4 жыл бұрын
its probably the thrust washer and bearing, Probably slide out when you were installing the bearing carrier
Great Videos! Did you ever do video on the lower unit prop shaft Seals? I cant seem to find it. Mine is 1990 Evinrude E40ELES looks same
@BrandonsGarage
2 жыл бұрын
kzread.info/dash/bejne/pnl1m7OBdM_UorQ.html
Iv hooked battery up backwards.so iv replaced the rectifier.but i didnt replace the relays switches.should they need to be replaced
Do you have an Amazon affiliate link to that ratcheting t-handle tap wrench I've seen you use sometimes?
@BrandonsGarage
4 жыл бұрын
Tap Sockets: amzn.to/2Lvyfyi Its just the sockets I use, with a 1/4 in ratchet. Thanks for asking!
@BrandonsGarage
4 жыл бұрын
Also, I'm really tempted to get adjustable type. (you'll see them when you click it)
I’m installing water pump kit on 40 horse Johnson it came with an oring but it’s not the one that sits on the under side of the impeller it didn’t even come with one of those it’s a slightly larger round oring what am I missing ?
Thank you for the great information. What would you do if you saw water in the gear oil in the lower unit?
@BrandonsGarage
3 жыл бұрын
change the oil, and pribably find the bad seal.
@jackfarrell4727
3 жыл бұрын
@@BrandonsGarage Brandon, would that mean removal of the lower unit?
Brandon, my question is,,,, If you don't put that o-ring on the shaft before you put the impeller on will it still pump ? When I took mine apart, it didn't have one so I left the new one out. Reinstalled the lower unit and it still won't pump. Pulled apart again and made sure everything was still intact. Reinstalled and still doesn't pump. Any advice ?
Where did you find that drive socket adapter
Hay Brandon my name is Chris I work at Mohave Powersports. Come in and see us. 1595 joy lane behind the Texaco.
Great videos! I have a 1998 Johnson 40hp that will need a tune-up and tilt-trim service. Does your 1993 40HP service processes apply to my motor?
@BrandonsGarage
4 жыл бұрын
Sure does.
Does anyone know if a 1994 30hp Johnson J30RERM leg, would work on a 40hp BJ40TERE, 40hp blew its bottom leg
@BrandonsGarage
Жыл бұрын
Oh heck no
Why isn't that bench grinder bolted down to the table? Kinda wonky how it moves all over your bench
How to resolve problem on my evinrude 35hp motor it's jumping and take out of gear
@BrandonsGarage
3 жыл бұрын
@Trajce Temelkov Take apart the gearcase, and inspect the clutch dog.
If you don't have both types of sealant, would just the gasket sealant compound work for everything
@BrandonsGarage
9 ай бұрын
You're not wrong
@tommyparker6187
9 ай бұрын
@@BrandonsGarage ok jw, I'm about to do mine and was trying to save myself the 20 bucks seeing inalready ordered the gasket sealing compound
@BrandonsGarage
9 ай бұрын
@tommyparker6187 I mean, the 3M 847 is great stuff, it won't wash away like the gasket sealing compound might.
@tommyparker6187
9 ай бұрын
@@BrandonsGarage is it the same as rtv? I already have tubes of that
Greetings from Finland. Not exactly to this video and not sure that you want to give a hint...but anyway. I have a 1990 Johnsson 40 vro, well not vro anymore thanks to you. And i take carbs from 50 hp evinrude and put them in Johnsson. But the fu##er lost a spark from lower cyl. CDI box and sparplugs (Champion) are new comp test showed 9,5 bar to each cyl. Lower plug is wet, so there is fuel. Next i was going to take the flywheel off and chek the coil. Any hint for anything else what could be the problem. Great channel, keep up good work
@sepponiemi2330
3 жыл бұрын
@LionelRichiesCrackpipe I did found the fault. It was the Cdi box under the flywheel. It was about to crack in two pieces, luckily wasn't.
@sepponiemi2330
3 жыл бұрын
@LionelRichiesCrackpipe In Finland there was a hp limit when you have to register your boat (still is). It was under 20hp or 4m lenght of your boat. So there's not ton's over 20hp outboard's on the market's from that era. It's 200€ for new updatet version of the trigger/cdi for that engine. Haven't buy it yeat, cause being building a mini jet boat...
Will a 1984 50hp Johnson lower fit a 1996 lower 40
@BrandonsGarage
4 жыл бұрын
No. Not a chance. Not even close. Completely different.
@Billeye
4 жыл бұрын
@@BrandonsGarage ok thanks that look close
@Billeye
4 жыл бұрын
@@BrandonsGarage do u have a power tilte for a 1989 48 hp evenrude
Ml
Do me a favor. Do not use your hands as hammers.
Oil is burned black thin and smells burned