One of my favorite camshafts for the stock cubic inch 302 sbf 😌 sounds fantastic
@edwardmcmillenjr8443 Жыл бұрын
Sounds good...nice lopey idle..hope the t5 transmission survives..
@natedog75200220027 ай бұрын
Hopefully my new build will fire up Thursday!! Same cam renegade 185 heads on a 347 with air gap intake and sniper 2.0 full system with timing control. Long tube headers and spintech 9000 mufflers. I hope mine sounds half as good as yours
@maxpugh9907 Жыл бұрын
The sound of a proper small block Ford no pussyfootin 🙌
@xitprofilmsx8 ай бұрын
you sound good my boy
@GT-Fresh-rp9qrАй бұрын
Sounds healthy 😮
@johnmcmillen8086 Жыл бұрын
Nice!!!!!!!
@raywaltdecuba569913 күн бұрын
Ghadayum!
@aaronruvalcaba7702 Жыл бұрын
Hos about street driveably? And hard pulls bottom/ mid end rpm?
@jamiegoff63276 ай бұрын
im swapping same cam and almost same heads! what length pushrods did you use
@superchomper20032 ай бұрын
I’m running that cam also and almost the exact same engine build as you. Mine doesn’t cam nearly as hard as yours does at idle. What idle timing are you running? And what idle speed? Thanks!
@YAboyboyGO707 Жыл бұрын
What timing chain did u use? I have the eedelbrock one and it won’t line up also my bolt out of my old cam was too small did u run into these issues ?
@Obertsgarage
Жыл бұрын
I used a comp cams timing set. If I remember correctly the bolt was different for new cam.
@maxpugh990711 ай бұрын
What’s the base timing ?
@francisbasson722310 ай бұрын
Do you run the stock spider roller lifters? I'm going to do the same camshaft with my 306
@Obertsgarage
10 ай бұрын
Yep
@76dream74 Жыл бұрын
I got the same heads.! what rockers you go with 1.6 or 1.7.?
@Obertsgarage
Жыл бұрын
1.6 Scorpion Rockers
@johnnychrisman6472 Жыл бұрын
Did you degree the cam in or just straight up dot to dot?
@Obertsgarage
Жыл бұрын
Dot to dot
@jeeplifted1 Жыл бұрын
Is this a stick bottom end car?
@Obertsgarage
Жыл бұрын
stock crank but has some eagle rods and pistons
@BradleyBeck-qp3te8 ай бұрын
Stock bottom end?
@Obertsgarage
8 ай бұрын
No. stock crank, eagle Rods and some summit pistons
@BradleyBeck-qp3te
8 ай бұрын
Are they the summit Pistons with the four valve release or just two
@Obertsgarage
8 ай бұрын
@@BradleyBeck-qp3te www.summitracing.com/parts/slp-h273cp40/make/ford its these ones
@josephmcmillen8544 Жыл бұрын
Lets get a walk around
@Obertsgarage
Жыл бұрын
will do. heads are being fixed but in the next vid definitely!
@powershift5439 Жыл бұрын
Wtf am I looking at?? Sounds bitchin, but I don't understand that rear bumper.. that the impact bar or what?
@Obertsgarage
Жыл бұрын
yeah just didnt have the rear bumper on it at the time
Пікірлер: 30
One of my favorite camshafts for the stock cubic inch 302 sbf 😌 sounds fantastic
Sounds good...nice lopey idle..hope the t5 transmission survives..
Hopefully my new build will fire up Thursday!! Same cam renegade 185 heads on a 347 with air gap intake and sniper 2.0 full system with timing control. Long tube headers and spintech 9000 mufflers. I hope mine sounds half as good as yours
The sound of a proper small block Ford no pussyfootin 🙌
you sound good my boy
Sounds healthy 😮
Nice!!!!!!!
Ghadayum!
Hos about street driveably? And hard pulls bottom/ mid end rpm?
im swapping same cam and almost same heads! what length pushrods did you use
I’m running that cam also and almost the exact same engine build as you. Mine doesn’t cam nearly as hard as yours does at idle. What idle timing are you running? And what idle speed? Thanks!
What timing chain did u use? I have the eedelbrock one and it won’t line up also my bolt out of my old cam was too small did u run into these issues ?
@Obertsgarage
Жыл бұрын
I used a comp cams timing set. If I remember correctly the bolt was different for new cam.
What’s the base timing ?
Do you run the stock spider roller lifters? I'm going to do the same camshaft with my 306
@Obertsgarage
10 ай бұрын
Yep
I got the same heads.! what rockers you go with 1.6 or 1.7.?
@Obertsgarage
Жыл бұрын
1.6 Scorpion Rockers
Did you degree the cam in or just straight up dot to dot?
@Obertsgarage
Жыл бұрын
Dot to dot
Is this a stick bottom end car?
@Obertsgarage
Жыл бұрын
stock crank but has some eagle rods and pistons
Stock bottom end?
@Obertsgarage
8 ай бұрын
No. stock crank, eagle Rods and some summit pistons
@BradleyBeck-qp3te
8 ай бұрын
Are they the summit Pistons with the four valve release or just two
@Obertsgarage
8 ай бұрын
@@BradleyBeck-qp3te www.summitracing.com/parts/slp-h273cp40/make/ford its these ones
Lets get a walk around
@Obertsgarage
Жыл бұрын
will do. heads are being fixed but in the next vid definitely!
Wtf am I looking at?? Sounds bitchin, but I don't understand that rear bumper.. that the impact bar or what?
@Obertsgarage
Жыл бұрын
yeah just didnt have the rear bumper on it at the time