So informative! Can’t believe you only have 20k subs with all the knowledge you share

The trick is not losing your mind over the doodads🤯

Great video Robert. Very in depth. Personally, I’ve never liked the wiring jumper hacks without clutch switches most people do when doing an auto to manual conversion. On my EK, I sourced the under dash harness from a manual car so the clutch switches were plug and play. I wish someone made a shifter hole plate like you made. I ended cutting out the shifter area from an manual EK, trimmed it to fit on top of my tunnel and bolted it down.

That first start was killing me. I was literally yelling at the screen so you would hear me saying to stop and check the wiring. I could smell the starter from here. Haha

Great video. This would have been helpful when I did my auto to manual and dual to multi a few years ago. Now if i can only get my hands on a b16 id be happy!

Loving the content fam , happy holidays

Outstanding!! Very helpful video to see what's involved

@hush22performance1

2 жыл бұрын

Thank you!

Save all the EF's!!!!!

They make a jumper harness for the dizzy I had got one off of Amazon for like $15 but your way of doin is also good to cuz an old harness like is good to take the loom off cuz my harness needed a lot of attention cuz a lot of the wires were cracked and splitting so I had to cuz an resplice them cuz I didn’t want them grounding and shorting anything out or catching on fire cuz it happened to my buddies EF sedan his whole engine bay and motor was torched cuz he had an old harness that caught on fire

Great video packed with solid information

@hush22performance1

11 ай бұрын

Thank you!

LOVE IT!!!

*_Awesome video!_*

Thanks i have the 90 DX with auto and will be swapping a B181 w cable trans.

Dope video!

The only one that needed knuckle swap was if your hatch is a STD 4 speed manual with vinyl seats

That’s crazy bro I am about to do this after Christmas except I am doing a Z6 with a ZC trans

Nice green acura 1.6 el behind us

But I was lucky I had a 91 EF Si in Tahitian green straight body no rust the A6 engine was trash the whole crank case was full of coolant the 1 at swap I did was swapping in a JDM D15B5 and converted it to OBD1 and once it was running I noticed the trans was shot as well I was gonna rebuild it but I ended up finding a 88 acura integra LS with a ZC and I used the trans which for that year was a limited slip cable D series trans then I chipped the P28 and she was a quick little beast once that engine went out after about 2 years from beating on her I swapped in a B18A but it still wasn’t as quick as before then did an LS VTEC awe I miss that car 🥲

Great video man! I got a question here. what's the difference between install the driver side mount first and install the rear mount first?

Bro Chris Sadowski is all over he has so many Cameos lol

Hey, I have a 1990 EF hatch. Same set up as you. Unfortunately the starter cut relay is “bad”. Where would you wire that in? The car also doesn’t have that button for the clutch, so you don’t need to push it down to start the car.

Another trashed frame rail 😭. There is an oem option for the alternator that fits. Unfortunately too late for this Rex 😢rip

But the only thing that does suck for doin a B swap in an EF chassis with hasport mounts is that when you have an alternator go bad there only 2 ways of getting it out is either removing the intake manifold which is a pain the slightly easier way is to jack up the driver side and remove the driver side CV axle 😪

@kaybevang536

Жыл бұрын

Da9 is like that too but I’ve been breaking axles in my 91 DA GSR Turbo because it can’t handle the power so it’s second nature to remove axles lol

@CarlosLopez-iy6jr

Жыл бұрын

@@kaybevang536 lol 😂 when I had my all motor build B20/V with high comp pistons I would slap drag radials on and tear up boots first pass lol I got pretty quick at swapping axles out too you to do them in like 15 minutes in the pits at the racetrack awww ☺️ bad times but good memories lol

@kaybevang536

Жыл бұрын

@@CarlosLopez-iy6jr Axle Breaks on a B series Swapped DA/CRX/EF be like : Aw Shit Here We Go Again

@CarlosLopez-iy6jr

Жыл бұрын

@@kaybevang536 facts 😅

Would love to purchase the cover plate for auto chassis..think it would play nice with acuity k shifter box ? I don’t see why not

What is the difference between the jdm and usdm frame rail ? Because the sir cames with a b16

do i need those shift linkages for my d series doing a manual swap?

Would a b18b1 pass emissions on a 90 civic? I imagine I need to change obdo into OBD2.

Hey man I got a question how much would it cost if you did it?

Where are you guys located and how much do you charge

Where are you guys located

May i knkw what engine is this?

Hey bro I just found ur channel like week or two ago...my question is have u ever done engine swap on 1994 Toyota Corolla with a k20 or k24

@hush22performance1

2 жыл бұрын

We have not

Hay man I need a 3 pice front end my brother

Is it possible to make a B16b California compliant?

@hush22performance1

2 жыл бұрын

Unlikely

Is the auto to manual plate into production yet?

@hush22performance1

2 жыл бұрын

It is linked in the description

@JoseContreras-mv5yz

2 жыл бұрын

@@hush22performance1 i thought you were going to make the part for the boot to go over it?

Hey can you send me a harness I need the same

I need some help maybe you can 🙏🏼

Would have been nice to start with a fresh motor bitch gotta giddy up and a half.