Bro- you need to pull your heads and make sure those later 350 heads are drilled for the steam holes that are specific to 400 engines.

@charlesnorris2993

10 ай бұрын

yea, reg heads that are not setup for the 400 need to have the steam holes opened up, also, new thermostat, good but specialy on the 400's, add a 1/8" drill hole on the outter rim of the thermostat, for air bubbles to easier pass + also add's a teeny bit more flow, my old cheyenne with a 400 i did 2 1/8 holes but my heads was original for the 400. also probably going to get some hate but not sure what temp that stat is, but if its a 195, try to find a 180. never had an issue with mine even in 112F temps outside.

Seen the first video on your 66 project and been watchin all the rest and had to subscribe. Working on a 68 myself and wasn't sure how the header panel comes off but your video was actually one that showed it. Good stuff bro keep it up

@cali530marcos3

Жыл бұрын

Thanks, appreciate u watching

Fan and shourd sounds like a great idea and it look like you had center bolt valve cover and 350 heads ? 400 small block had steam holes in the heads and blocks I like 400 small one of my favorite engine. Good luck with you fix .

Bigger Big Block 😁

When can we expect another follow-up video!? I enjoy the project and you give me ideas on my '66 Impala

@cali530marcos3

Жыл бұрын

I’m editing one right now, took it to get the exhaust done

what a beast !!

@cali530marcos3

8 ай бұрын

Thanks

When i was changing out my pulleys i was literally going back and forth the autozone probably like 10 times in a day trying out different belt lengths. Because one would be to short or the other one barley to long. Lol i ended up with at least an extra 8 belts that ive now had in my trunk for years haha

@cali530marcos3

Жыл бұрын

Yea it was stressful because everyone trip to the parts store took like 45min and I wanted to get it done that day

Am working on an overheating 400sbc as well. Bored 0.040. looking to cool it better.

@cali530marcos3

Жыл бұрын

I took off my electric fans and put a mechanical clutch fan, also with the stock pulley it seemed to help it stay cool, now all I need is to install a fan shroud and it should be good to go

Bro you have a nice set up; engine and the inside engine bay area. I have my alternator on the driver's side also. I didn't think I could put a power steering pump set in there. I'm glad you made this video. Keep up the good work. I push a 1963 impala coupe hard top with a 327 under the hood. Also I like your roller motor, I once rebuilt one of those in my garage adding roller rocker arms arm as well. I live in Stockton, Ca. What city are you representing, if you don't mind me asking?

@cali530marcos3

Жыл бұрын

I stay in woodland, ca about 40min from Stockton

@eliasalmada5156

Жыл бұрын

@@cali530marcos3 what's up g

Having a fan shroud would be much better.

@ 5:26 & 9:45 calls it a name. That's how I mechanic.. lol

I'm working on my 70 monte carlo and i chose the fan and clutch with thermo. Instead of electric fans.

@cali530marcos3

Жыл бұрын

Yea it looks kinda empty with just electric fans so imma do the clutch fan with shroud setup

I have the same setup went with a Fan shroud GM clutch fan same radiator. temperature stays at 165

@cali530marcos3

Жыл бұрын

That’s my next set up thanks for the info

Love your videos brother, reaching out from Jersey Shore 👍 Question on headers.. my 65 impala with power steering and 283 .. I saw 1 video that you finally got the right header.. which on was it ?

@cali530marcos3

6 ай бұрын

It was a non hugger header, I think the brand was headman, there’s another video were I got the exhaust done finally

Saludos desde la cd de Mexico comentarle q no hay respuestos como los q le esta colocando a su chevy, se batalla por q nuestro mercado es muy escaso aqui debe de hsber solo 3 chevy del 66, un numero para contacto

@cali530marcos3 are you going rewire the car with a kit?

@cali530marcos3

Жыл бұрын

Yes, I bought a new wiring kit from American autowire like 6months ago, im just waiting to install my exhaust system and also I want to paint the inside of the car

Have you checked the heat cross over under the intake did you block the ports properly

@cali530marcos3

9 ай бұрын

The edelbrock manifold I installed didn’t have that option since it’s a high rise intake, but I’ve been driving it and it seem to be fixed

Steam holes drilled in heads? My 400 stays at 180 but smokes white out of breather only no smoke out tailpipes any ideas

@cali530marcos3

Жыл бұрын

Yes the heads haven the steam holes drilled, I was thinking maybe the under drive pulley was spinning the water pump too fast, I’ve been thinking of going with a fan and clutch assembly with a fan shroud to see if it stays cooler

@josephmclovin9763

Жыл бұрын

Oh- sorry, just saw this

@ronnelson7828

Жыл бұрын

That aluminum billet pulley spins the water pump slower, not faster.

It seems to me the pump would spin faster with the larger pulley?

@mickangio16

28 күн бұрын

You are correct.

What oil pump are you running in that engine

@cali530marcos3

Жыл бұрын

It’s a high volume low pressure pump I got at summit racing,

Calling parts on your car a whore is the most relatable part of this video lol

@cali530marcos3

22 күн бұрын

Haha, yea pretty much

If your temp sensor is in the cylinder head it will read hotter than at the thermostat housing.

@cali530marcos3

Жыл бұрын

Really, well I guess it makes sense since that’s where the exhaust gas’s comes out of, there’s a port on my edelbrock manifold that’s next to the housing, I’m going to try that one

What engine size is this

@cali530marcos3

Жыл бұрын

It’s a 400 small block Chevy bored .30 over so now it’s a 406

Hey man! do you know heads those are by chance?

@cali530marcos3

7 ай бұрын

No, they are center bolt valve covers so I’m guessing tbi, they probably just drilled the steam holes out

If it applies, what vacuum port is the distributor advance routed to? Ported or manifold vacuum? Having it to manifold should help it idle with a bit advance, idling cooler. Worth a try

@cali530marcos3

11 ай бұрын

I have it on ported vacuum, replacing the lower pulley and adding a fan clutch fixed my issue

Why put a smaller motor in?

@joshuagarvey9362

10 ай бұрын

Love the 400 sbc.Biggest motor.

Given that you have enough initial advance, overheat at idle, not enough fan, overheat on the road, not enough rad

@cali530marcos3

3 ай бұрын

Doesn’t really overheat anymore, but I think a clutch fan and fan shroud should really help it out and keep it cooler

I wouldn't have it without a fan on the pulley and cowl

@cali530marcos3

2 ай бұрын

Yea, going to be putting a clutch fan on there and adding a fan shroud

@Turner.1

2 ай бұрын

@@cali530marcos3 lots of guy throw the Kowloon away,but it helps to cool the engine by at least 15 degrees,and thats alot considering the combustion temperatures

Simply put zinc in your oil and take the thermostat off

I hate that.. almost ,, ugh..

@cali530marcos3

Жыл бұрын

but then again when are we really satisfied with something, there is always something

Since you are having problems with it just put an Ls1 problem fixed ! hahah

A smaller bottom pulley would make you WP turn faster and essentially cool better. A larger pully slows it down. Wouldnt it? If you had the alt belt on diffrently you could have saved a few bucks buying a new one :) and a headache lol You also could probably have just used a long WP from the get go since you have electric fans and all the extra space. Lining up pulleys on a long pump is so much easier. If it has an electric choke, pumping it like that wont help it start (generally).

@cali530marcos3

Жыл бұрын

It’s a manual choke but it’s not hooked up, and for the small crank pulley I thought the same thing, I thought it would cool better but it was running hot, then when I swapped out to a larger one it cooled it down like 10-15 degrees. I was thinking about switching the alternator to the other side too because it looks too empty on the passenger side like it’s missing something

@joshlepley1306

Жыл бұрын

@@cali530marcos3 well dang. My setup is basically identical as what your doing. I havnt started the engine yet but I have a small crank pulley also. So ill have to watch my Temps to check that.. All my stuff is on the driver side also. It is alot but I figured with the space on pass side I can mount some AC someday and even out the look

@mickangio16

28 күн бұрын

Bigger crank pulley spins the pump FASTER.