Dear sir. This is brilliant! However, I may have some suggestions, to increase the output, quite easily. The diodes in the rectifier will eat up at some 1,5 volts and produce heat of that, if it is a standard silicone bridge with 0,7 to 0,9 fall over each diode. 1,5 V is quite a deal if the generator produces some 3 V. It is 50%, that get lost. If the bridge is built by 4 shottky diodes with 0,4 V fall over each diode, and just eats up 0,8 V over the bridge, the losses will be decreased by a half, and the rectifier would be close to 75% effective. From the generators 3 V, there will be left 2,2 V, instead of 1,5 V. Next thing is to increase the number of turns in the serpentine coil. By doubling the turns the voltage will be doubled into 6 V, and there will be 5,2 V after the rectifier, and the rectifier will just eat up some 13,3 % of the power. There will be a limit, depending of the space allowed for the windings. The general rule is to keep the windings as tight as possible, and as close as possible to the magnet field. A millimeter closer is crucial, and can make the 6 V output into 12 V, and Now we talk. 12-0,8=11,2 , and the rectifier will be 93% effective. This correction, will increase the mechanical resistance in an equal way, similar to the voltage gain. I.e. It would not spin as easy as before. This was suggestion 2, and 3. You never get something out of nothing. But there is a fourth thing to consider: You can always use a transformer, to multiple the voltage, before rectifying. There is no rule that says that you can't get 230V out from a 6V source. But a transformers efficiency depends on the frequency, and what kind of iron that suits the best.. For frequencies say 30-400 Hz, standard E-I steel-blades works relatively good as core material, but over that, it becomes more and more complicated, though iron powder and ferrites will be better to suit the frequency. A solution like this with windings at the peripheral, may well produce kilohertz, as well as 20 Hz, and no iron suits this span. You would also have troubles to handle a span from 3V to 3000V, but all is dependent of the Min-Max spread. This is very complicated, and transformers are not 100 % effective. My suggestion to make a generator is that it don't exceeds 35 V in a storm condition, though you can use cheap electronics to charge batteries, that will hold the energy, that can produce other voltages for needs. But consider, that there are losses involved in every stage. Use step up, or step down converters i.e buck-boost controllers, use MOSFET transistors, and the best quality capacitors and inductors, to minimize every loss. Take care to search for the less needed stages for it's need, and Keep It as Simple as possible. So dear Mr R.M. Smith: I love your turbine, and the way you preaches simplicity. I totally agree with you. I just wanted to add some thoughts. I am a Swedish, over aged engineer, that can't resist work, though I am alone, so I stay halftime. I love to watch your movies, and loves your wonderful laughs. My best regards.

@justtinkering6713

Жыл бұрын

Transformers will increase voltage or current but not watts. Also a low impedance winding on a transformer will greatly increase the load. The rpm will suffer as will the power

@screen-protector

Жыл бұрын

I agree that you can use and Shottky diodes, yes, that's right. But, this was mentioned even in this video here and before. This is a proof of concept, Robert was telling to put the money where he's mouth was. ;) Making it dead simple to create and play with it at later stage. It's not about the perfection ;). Yes, you can use transformer, but, if you're going that far, worth mentioning that a linear transformer has a higher loss than a high-frequency one ;) - less windings, but you need to understand the MOSFETS and the protection circuit ;). This efficiency would be better than a regular transformer. As you've mentioned about the frequency, you know what I mean about the switching power supply and its uses. Because you don't want switching one for instance in the audio system of a higher quality ;), or medical stuff. As per your other suggestions, why not do something and show it to everyone? :) You could put your money where your mouth was. :) That would be nice to see as an improvement and you don't have to 3d print even :). If you can achieve a higher efficiency, you can use materials from the recycling :) and will have a better efficiency :). But hey, it's me and my opinion, you can do what you like ;).

@philip5940

Жыл бұрын

There's a way to wire up MOSFETs or suchlike to yield no voltage drop rectification. Cost and simplicity though I don't know.

@justtinkering6713

Жыл бұрын

@@philip5940 its called a synchronous rectifier.

@justtinkering6713

Жыл бұрын

If all your interested in is a voltage boost then just make a Schottky Bridge Doubler Circuit. It doubles the voltage It only has 4 diodes and 2 capacitors. I've used them many times

I don't know how this gentleman has not got 1 million subs. Excellent valuable information.

For those who wondered: 1.7 m/s wind speed = 6.12 kmh / 3.8 mph / beaufort force 1-2 / 'light air'-'light breeze'.

@ThinkingandTinkering

Жыл бұрын

cheers mate

@bdanuw

Жыл бұрын

Yes so very promising right ? ​@RobertMurraySmith I went for solar so I could have a few of the bits and pieces to allow to plug stuff like that in... I really hope it is indeed possible... generators like that for gateways and other remote devices that can charge at any time of day (maybe couple with a small solar panel to be even more resilient would be great to try too... Anyway really awesome to feel like it may be just be round the corner...

@Anti_Woke

Жыл бұрын

@@bdanuw Yes, but I'm sure Rob would point out that by the same token, it probably won't survive a gale! For prototype 'works' is good, but for a real thing you'd want to design for the strength of wind you expect.

@ctakitimu

Жыл бұрын

@@Anti_Woke Or a way to restrict airflow for higher winds

@Anti_Woke

Жыл бұрын

@@ctakitimu I'm designing for use on a small sailing boat, wind speeds up to 40mph - and being able to pack it away when the winds get higher than that! Obviously that places significant structural demands on the system, not just the turbine, whether it's collecting or deflecting the wind. (Working on sailcloth Darwin funnel, hoisting more or less as the wind conditions dictate, or collapsing the whole thing to pack it away)

I was taught the "KISS THEORY" at a very young age and it has served me well for many years.

@ThinkingandTinkering

Жыл бұрын

it is a good way to go for sure

@lesmaybury793

Жыл бұрын

Same here, it served me well for decades.

@jamesjallalabad3783

Жыл бұрын

The judge said I can’t do that again

@ravenmad9225

Жыл бұрын

Rock and roll all night and party every day.

@Buzzhumma

Жыл бұрын

@@jamesjallalabad3783 😂😂😂

Fantastic videos on projects using basic physics and electronics. I like just watching the great refreshers on basic electrical components.

You nailed that idea keeping things simple. I used to over complicate designs to the point where it stayed in my idea book. I've learned to just keep it simple... actually build the dang thing, and complete the project. I live with the design for a bit ....use it, look at it and think of ways to improve it. Sometimes, I'll iterate. Other times, I'm completely fine with it

@ThinkingandTinkering

Жыл бұрын

surprisingly enough that takes a fair bit of learning lol

@evo-labs

Жыл бұрын

I think a better question to ask its "can I make it MORE simple/LESS complex". In engineering, complexity is relative, something than may appear to be 'complex' is often as simple as it can be, just not as simple as the observer expects it to be. Of course when you add cost into the equation, the simple vs. complex argument becomes polluted because less complex is associated with lower cost, that doesn't necessarily make the product better.

Dear Robert, I stumble across you and your work on KZread and Thingiverse all the time! You amaze me with your intelligence and ingenuity and you brighten my soul with your infectious laugh. People like you are what makes this world a better place! That isn't poppycock, isn't that what they say over the pond :)? It feels like a small world at times when I see a really interesting 3d print and it is you. Well that just happened the other day, and that was when I saw that you lost your beautiful bride, I watched her video with a tear in my eye thinking what you are going through. I never leave comments ( seriously never ) but for some reason, I felt a pull for me to reach out just to let you know, that there are people out here that care!

A rim-speed generator built-in to the turbine of a wind-tower of the kind you've been prototyping recently seems like a superb way to go for many applications.

@ThinkingandTinkering

Жыл бұрын

I am liking the way it is performing for sure

@mahirbalayev5835

Жыл бұрын

​@@ThinkingandTinkering hi. I have one idea and I'd like to know your opinion. What do you think about applying venturi pump to hydro power dam? I mean, if we could connect venturi inlet to discharge of dam we could create 7/24 environment friendly wind and by applying one of the super efficient wind turbine to air suction for creating energy. But I have some doubts about if it will decrease efficiency of hydropower. What do you think?

@TheBaconWizard

Жыл бұрын

@@ThinkingandTinkering I didn't realise you'd done it, I thought you'd only tried it with a PC fan as the generator! Edit: Such as in 1835

Looks great Robert,works great looks, it looks allot like the kite I told you about years ago that I bought as a kid, they were army surplus (I was told by the vendor in the golf area of the United States). They were made of Styrofoam, and had orange and white coloring on the rotor portion so that the colors alternated as it spun. With the wind on the beach they would stay flying without attention, he had them staked out all over the beach, which is how I purchased one. The string for the kite was attached to the pivot point in the center on either end of the spinning drum and joined together as one Kite string. Thanks for this build! Always wondered how it would do. Excellent. The kite had an airfoil cross section of each of the two rotors blades. I really like that you have revisited this with flare. Your rotational ventilator cap generator was great as well. And the later variation with it's isolated salvage transformer pick up coils was a stupendous build also. Great stuff. Would love to see how one made of industrial insulation 10 feet tall and five in diameter would do it, but hey all you need to do a scale of the math right? But still I wonder what a big beast might do. Honestly I could say I would really love to finish my years living in an active version of a dutch windmill with this thing for a rotor built into it. Or maybe just a dutch windmill with him create parts, there's a lot of room inside of one of those, perfect for me. I always wondered how a design like that would work at the peak of the roof on my house . ...

Yes, simplifying things is the way!!! I managed to simplify radius calipers the other day, down to one moving part. Now they look deceivingly simple for what they can do lol, but now I need to prove their capabilities with a better refined version. I loved the fact that this could just be blown by a person 🤣 Incredible results, Rob!!!

Great video and some really excellent tips on design for both new and old designers/makers. Would love to see the output of a small "wall" of these under real wind conditions. 👍👍

I'm always 50/50 on the idea of simplicity in engineering. Its benefits are obvious, but that same mentality would rule the car, plane, even computers as too complex to be worth it today. One can try to point to the goals of Mercedes and the Wrights being exceedingly simple compared to where we've carried those technologies today, but that's just the thing. It's nearly impossible to get simple devices off the ground these days. We're so jaded with so many "mature" technologies, fledgling tech and alternative paths have a hell of a time competing, especially since engineers are very fond of the stagnant legacy "if it ain't broke, don't fix it." And that's not even touching on problems created by market behemoths having every tool possible to shoot down the little guy with governmental help in some cases. There are a lot of alternatives we should be looking at to replace windmills, yet were still using the same basic design used in a pedestal fan because the old farting dog we named Industry knows it has the best approach if no superior method is sought and found. And with no real competition, why innovative? Where was I going with this..... End of the day, something shouldn't be simple or complex, it should only have the level of complexity it needs to function, plus the safety factor. Edit: And then there the "best solution is not to have the problem in the first place" people. Anyone who seriously invests in that brain dead platitude should be handed a gun with a single bullet and reminded that, according to their own philosophy, they now have the means to solve every single problem they have, have had, and will ever have, so how about a demonstration? The rest of us have things to do.

@ThinkingandTinkering

Жыл бұрын

no mate simplicity Is always present - it is made as simple as it needs to be - a computer is a stunningly simple thing - it is just switches arranged small and that's all it is - when it comes to manufacture the approach is always the best part is no part and the best process is no process - a ton of effort goes into reducing component count - I think you might have some confusion between simplicity and simple

@user-kr3pc1us2t

8 ай бұрын

If the main subject is "keeping it simple an cheap" there will be no progress. Because simple and cheap is not progress. Savonius can only become more efficient by making it more complex. Efficiency must increase with the same swept area.

@custos3249

8 ай бұрын

@@user-kr3pc1us2t Largely my point. Further, a bit surprised RMS gave me pushback. For all the times he's commented about people doing exactly what I said whenever he makes a new generator, expected a different reaction.

@user-kr3pc1us2t

8 ай бұрын

The human talk to suit himself. Sometimes by closer inspection one can see what suits the human. There is a saying " in the land of the blind the one eyed is king

@user-kr3pc1us2t

8 ай бұрын

Hi Custos. If nothing in a design change , the result stays the same . This channel is about marketing of 3D Printing. To do the print you must create a 3D model of something using CAD. The CAD file is then converted to a STL. File this file format supports 3D Printers . So if I want to sell a 3D Printer to a novis I must have exciting things he can print. So If I have STL files that I can supply all the novis must do is learn to operate the Printer and load the STL files. So if you are a turner and machinist and you know CAD you can do CNC programming also. So for the novis everything must be simple and cheap

I was thinking of something similar, though with a sphere with angled slots. After seeing this one in action, I may be rethinking that idea. Can't get much simpler and doable than what you have there. Thanks for the video Rob! Outstanding!

In a windwall configuration, if you stacked them, design units to rotate in opposite directions. Each unit could have magnets on the top, and coil on the bottom, and alternate the rotation directions as you stack them.. The more you stack the more power you get, and each unit gets double the effective RPM because it's rotating in an opposite direction of the one above and or below it.

@heinerphilipp

Жыл бұрын

Smoke another one. The next idea will be much better.

@donaldgulledge729

Жыл бұрын

A stacked counter rotation version I would really like to see. I believe just inverting one of two identical units would result in the one on top rotating opposite of the one on the bottom so your build cost would still involve only one design. I believe it would however require including a axel bearing on both ends rather than only on the generator end as shown. This would be a great project to upscale test.

@Glenharris1971

5 ай бұрын

Exactly what I was thinking. Add cowlings also.

Can't wait to make my very own! Love the idea!💡 Thank you for all the brilliant videos 😊

@ThinkingandTinkering

Жыл бұрын

awesome mate and cheers

6:20 :) i can feel same happiness as you Robert. Thanks for so mind blowing videos..

You enjoyment in testing your experiments is absolutely infectious! Keep up the great content Robert!

I think the easiest way to get a project like this going for parole is with some BMX bike rims or even big racer rims . All the bearings and balancing is already done and power at the rim is what it's all about ! I think i might get my thinking cap on and work out how I am going to fit a serpentine coil cos I am a huge fan of that idea!

I'll never make any of these things but he's such diamond geezer that his joviality makes my day.

I experimented with alternative energy for years. It turns out solar is the way. Quiet, simple, no moving parts, works very well, cheap. It is truly “free energy” and it is readily available. It turns out the true conundrum and unsolvable problem is cheap or free (desirable) land. Cool toy though.

Thank you for the video.👍. The one I want to make, I will put a longer axel and a nut on top, so it not flying away 🙂

Another thing about the design is too that imagine doing this rotation section for generating power on a bicycle or even a foot style pedal from a old fashioned lathe.

I'd love to see a video where someone (a viewer maybe?) sets some system up in their garden and actually charges a home system with it. Is there any RMS forum where subscribers / viewers share their examples? I fully plan to have a go myself someday and would love to share that experience somehow as well as see others.

@ThinkingandTinkering

Жыл бұрын

Angelus runs a discord page which can be found here mate discord.gg/aFuTTdy8J8

@lilolmecj

Жыл бұрын

I don’t expect a garden size installation to power my whole house but I would love to figure out a way to have one that was attractive and produces enough to say run some lights in my garden.

Excellent display of the simple and effective ways of energy production, I would recommend this type of home generator.

What you said Robert is a fact. Simplicity of design is what makes things work beautifully. Making it easy for others to copy and use the idea and pass it on and on. The copper coil wire needs to have a thin layer of silver on the outside of the magnet wire then the insulation finishes the magnet wire specifications. The silver plate really increases the efficiency of the coils. . Job well done fella too. vf

Very good presentation, I thoroughly enjoyed it ,Thank you....

Yes sir! Simplicity is always overlooked.

Putting the magnets on the rim makes a fantastic more efficient fly wheel brilliant. Onwards and upwards 👏

@ThinkingandTinkering

Жыл бұрын

cheers mate

Excellent, thank you for sharing. We waste so much free energy we could harness, e.g., the hot moist air blown out of our AC condensers; we could harness the wind, heat, and the moisture from it.

I have had for years a desire to make an injection molded savonius turbine had can be put up on the roof by the costumer himself. Thank you for showing that!

@ThinkingandTinkering

Жыл бұрын

That would be cool

Commercial vehicles, such as vans that use a Fletner system to extract air from vehicles that carry noxious chemicals, or carry animals, would benefit from this to charge their batteries on EVs or a leisure battery on motor homes. I’ve been pondering this ever since your efforts using the microwave motors a few months ago. Love your enthusiasm 👏👏👏

About 7 years ago, I designed and built a hot water heating system, for my house, to supplement the propane heater. It was caveman simple, with me knowing only minimum about efficient heat distribution. That system, today, is somewhat increased in complexity, but efficiency is such that it can complement or replace the propane system at need. Now that I've started designing an electrical system with similar goals, I'm glad you've reminded me to KISS (and to laugh... important to have fun when tinkering).. I've a tendency to start too complex in the design process (much to my own detriment, often enough). I've got some thinking to do

Yeah, I think many of us struggle with overcomplicating things. So, thanks again for another great reality check. Keeping it simple gives surprising good results.

@ThinkingandTinkering

Жыл бұрын

for sure mate

Your videos truly inspire me to try new things. This is awesome!

Thank you. lol few hours after watching this I'm half way to finish making one. hopefully getting decent volt too.

an observation i had while watching it operate with the air blown onto it is the magnets were lifting the rotating assembly which would reduce efficiency (LOL) but also easily and cheaply solved by having means to hold it in position at the top. great video rob :)

Thanks for sharing. Power to the people!

Awesome. I'll try that one! Thanks for sharing :)

Very cool! I am an rc glider guy and always wondered if anyone is looking at the dynamic acceleration that we take advatage of for dynamic soaring. A wind turbine placed on the same angle straddling the front side/backside of a ridge that we fly on would provide a constant acceleration as all sides are flying a down wind pass.

Never a truer word spoken, I have many good intentions in the garage waiting to be finished. But I do see the benefit of a 3D printer to complete most of the hard work.

@ThinkingandTinkering

Жыл бұрын

I just set it going and go and make a cup of coffee lol

Like great and good, best is better; thank you for underrated simplicity.

Hi Robert. An excellent prototype and presentation. I'm a Geophysicist and the serpentine coil has got me inspired. We do EM surveys to find metallic minerals. Now drones are the go. So I will look into the transmitting and receiving from such an efficient coil. Yes frequency maybe the issue.

@ThinkingandTinkering

Жыл бұрын

I am intersted in how you get on with that mate

@karaoke832

Жыл бұрын

@Robert Murray-Smith Thank you Robert. I will try and be as open as you if I manage to use this excellent coil in real surveys.

You are my kind of designer, simple concept easy

Dr. Smith, your selections of videos would compilate into a complete system. I'm ready to see a whole system built by you. Generator and storage. Just like your wind turbine make our world spin. LOL

I’m only 30 seconds into this video and I already love this guy.

Love your enthusiasm 👍

Great video! It would be very helpful to set up a test stand where standard size VAWT models could be compared. For example, take out the Savonius turbine and put in a Ugrinsky, adjust the load to identify the load and RPM at which each model produces the most power for given wind speed. A service where standard size VAWT models could be sent in for testing would be wonderful.

Killer build Rob!! You can switch your atmosphere energy collector with a reed switch actuated by the permitter magnets on this turbine.

@ThinkingandTinkering

Жыл бұрын

cheers mate and nice!

That is awesome!! Great point on making it easy to reproduce.

@ThinkingandTinkering

Жыл бұрын

cheers mate

Looking great Rob .. love what you are doing!!! 👍

@ThinkingandTinkering

Жыл бұрын

cheers mate

Brilliant stuff thanks

I love the project and will consider it as one of my first projects when I get the 3D printer I am planning on in the near future. I would be interested to see the effect of adding some low reluctance steel strategically to boost the magnetic field.

How about a bottom AND top magnet and serpentine coil assembly? It might be more balanced? Your laugh is infectious by the way. Much as is your unmatched enthusiasm!

Well, we always knew RMS was full of hot air! LOL Love your projects.

Simplicity is the essence of genius - Albert Einstein Capex, maintenance, labour, all easier that way. Got to love it.

you could put magnets on the top and bottom slightly offset to reduce drag while doubling the amount of coils and maybe replace the plastic winding bits with iron cores as i'm pretty sure that would make the field stronger as it passes, to keep the upper coil stationary just add a C frame holding the top and bottom coil plates as a set

Great work.🥊

Agreed on the simplicity needed to actually manufacture something. Although, clearly we reach a point when the simplicity goes out the window, as it does for engines and power steering systems and the like because the demand for robustness outweighs the easy of keeping things simple. Looks like the automotive industry figured that out a long time ago but, I do think they go overboard at times lol. To start with, your 100% correct on simplicity, to go forward however requires more complexity. If they can build millions of cars and have been for over 100 years, then I reckon anything can be made cheap enough to manufacture given time and infrastructure.

@ThinkingandTinkering

Жыл бұрын

simple and simplicity are not the same thing - simplicity as it needs to be is a quest for reduced process and component count

That's fantastic. Thanks for that. I want to see the next video where you blow on the LED to make the turbine spin :)

New sub here...love it! I built my own design and manufacturing business a couple decades ago. Simplicity is Godliness! Agreed! It's what USED to make Mercedes Benz, a Mercedes Benz! Simplistic, efficient cars that would run forever. Use quality materials, minimize moving parts and complexity and viola, you have half million mile cars as the norm. Today? They are techno piles of junk after a few years. Rain sensing wipers, active headlights auto dimming this and that. Just heaps of complexity to fail and a fortune to repair. Old MB headlight went out? A new bulb was a few dollars. (U.S.) New MB headlight goes out? You have to buy the entire housing with this plasma generator and radar module etc etc $500.00 please. No thanks.

That contagious laugh gets me every time😂 Thanks buddy 👍

Excellent, Thanks Rob!

@ThinkingandTinkering

Жыл бұрын

glad you liked it mate

I love it! I've been interested in trying a lot of different generator designs. I WILL try this design. It is practically begging to be mass-produced.

Awesome video Robert very interesting project!!!!

You really convinced me to try the snake coil. This really is a magic video. Do think about bearing on top because now you have a lot of flutter resulting in wasted energy. Thank you, as I said, magic!

I would be a much better professional, if those videos where available at my electric student time. Thanks Robert, and keep it simple and executable.

great skills great fun thanks rob

I contend that if you're going to 3D print the turbine you may as well have 3D printed the Ugrinsky turbine, which is significantly more efficient. You don't benefit from the Savonius being simpler if you aren't manually making the turbine and are just printing from existing models.

Awesome stuff Rob..really impressive performance for such a little unit. Thanks for all the hard work you do bringing these great little devices to us!

@democracyforall

Жыл бұрын

THIS IS THE ONLY TURBINE I USE AND THIS IS THE ONLY I KNOW FOR THE LAST 30 YEARS HA HA HA HA .

Great, thank you

These are super cool and I'd love to make something simlilar myself! One reccommendation to anyone else making something similar; Put iron cores in the wire bobbins, a nail or a bolt is a cheap and simple solution and the practical magnetic flux achieved by a ferromagnetic core can be orders of magnitude greater than an air core at the frequencies you're switching the magnetic field at - this will put greater resistance on turning but with a good breeze this should be more than powerful enough

Great Idea, Thanks for the info.

@ThinkingandTinkering

Жыл бұрын

Glad it was helpful!

Yes, impressive, thanks

May the Sacred Lotus of Divine Light Smile upon you with Divine Unconditional Love Peace, Joy, Harmony, and Happiness and Gratitude for gifts from Above Friendliness, Compassion, Good Health, Strength of the Elephant Abundance, Freedom, Peace, Love, and Joy Relaxation, Rejuvenation, Ecstasy, longevity And Fun I am Unconditional Love I am Divine Joy All my needs and desires are fulfilled even before I realize what they are Which will always be for my greatest good and most beneficial good of all

That's amazing. I'm thinking of how to build an array of these using paint buckets from the hardware store. Thanks.

Rob You are on to something with this latest subject and this design A great project Al

Amazing!!!

this gentleman is brilliant! I wan't to install this on my car.

Hi, may I suggest that if you were to deflect the wind away from the returning blades on the opposite side of the working direction of the wind by adding a directional tail to it you will enhance the efficiency of your turbine a great deal! Vertical axis wind turbines all suffer from this to overcome the force of the wind on the blades on the opposite side of the working direction and all future VAWTs will benefit from this addition. I am currently working on the concept with astonishing results.

Good engineering sense! The best is the enemy of the good!

Watching you laugh as you use your own breath to power your generator and light an LED makes my day. Please keep on keeping on!

@partciudgam8478

Жыл бұрын

I remembered the three piglets and the wolf fable... "open up or I'll blow and blow untill your LEDs melt!"

@ThinkingandTinkering

Жыл бұрын

lol - cheers mate

@rowgler1

Жыл бұрын

@@partciudgam8478 I just saw a Far Side cartoon- The three little pigs were in a brick house looking out the window at the big bad wolf handing a fist full of dollars to A Kool Aid pitcher with legs.

I would say that logically, indeed, do start out simple, make it, then, if you are then inspired enough, you will have one while you make anything more complicated later on when you are more inspired from a first success.

It would be a cool to see a savonius turbine with your radial "feather" type generator on top, or perhaps VS a stack of your radial feather designs with adequate spacing. Just love all these prolific videos and designs as well as testing-floats my boat if you will.

@ThinkingandTinkering

Жыл бұрын

Cool idea

Another knockout build, keep them coming

Thanks!

@ThinkingandTinkering

3 ай бұрын

no - thank you mate

I think the best compliment I can pay you is to compare you to professor Eric Braithwaite who was amazing. Great video's wish a tv channel would pick up an option for a tv show of what you do. Never stop.

There are lots of 18th century inventions that worked, they're simply less efficient than other methods of doing the same thing. This is more massive than simple propeller blades for the same amount of wind trapped for power. I'm told it's used on Amish farms because it's easy to make by splitting a steel drum in half.

@1953Wes

Жыл бұрын

Another example would be flame licker engines. Then there's the Atkinson cycle engine, which is actually more efficient than Otto cycle or Flathead, but the gain is not enough to pay for changing over production lines and increased costs for building them.

I remember large scale of these stacked on top of each other in orange groves and rosemary groves in Florida in the 80s most were not still in operation at that time and I always was curious what they were I ask someone who worked the groves a old timer he said they would power the Irrigation pumps free electricity I now under stand

Very impressive. Bravo.

@ThinkingandTinkering

Жыл бұрын

Thank you very much!

I wonder how many thousands of people you have inspired and are now copying your inventions love all your videos thank you .

@ThinkingandTinkering

Жыл бұрын

I wonder too mate - but I am guessing we will never know!

You could build these into fences to alleviate wind loading whilst generating power. No loss of privacy.

You are truly a breath of fresh air, electrifying, the result of a K.I.S.S. I ❤ it.

Wise words as always

@ThinkingandTinkering

Жыл бұрын

cheers mate

Excellent 👍 very interesting stuff.

Keeping it simple works in line with the power generation, these small energy outputs are easer to learn/work with. The bigger the generation, then essential life safe systems need to be in place.

@ThinkingandTinkering

Жыл бұрын

absolutely

Very nice, good job!

@ThinkingandTinkering

Жыл бұрын

Thank you! Cheers!

That's really great stuff! Correct me if I'm wrong, but the induced current is strongly related to the magnetic field strength, so the output would be greater if you turned the base upside down and move the bar to poke out the opposite side of the base. The magnets would be 3-4mm closer to the coil.

Savonious cool! Idea here. Wind speed reactionary savonius stack of multiple units within reasonable limits rides within protective tube. Lowest operable wind speed entire stack is raised/higher operable wind speeds the stack lowers fewer stacks stay exposed.

Dude, you are a GENIUS!!!

These would be perfect to place on the corners of the compressor for an air conditioning unit. I live in Florida and would love to scavenge a little electricity from the AC running most of the day. Thank you for the great videos!

@ThinkingandTinkering

Жыл бұрын

nice!