Awesome practitioner of the black arts. Kudos for the adept use of vintage test gear to boot! Love yr enthusiasm keep up the good work maaate!

Use a pencil for a pointer, the xacto knife is making us nervous specially when pointing at the SA's graticule :) Nice video !

@vk2seb

7 жыл бұрын

Also the tip actually warps the trace a little bit if it gets too close as it's slightly magnetized ;). Cheers!

@christiancampbell466

3 жыл бұрын

I came to make this same comment. I can’t hear what you’re saying when the blade gets too close! =‑)

@keithnoneya

4 ай бұрын

@@christiancampbell466🤣🤣🤣

Fantastic video. Thanks!

Great video, very real and life like. No pretense!! cool

it is a nice project and nicely designed board. it this possible to know from where did you get your PCBs made?

thank you

Thank you so much for this video. If possible I would like to ask a question. It's facinating you have this knowledge of these multiplexers , multipliers that work on RF. I too am interested in catching up with such. Could you pls recommend a book that has this knowledge?

Oustanding!

Were it me, I would have edited the video just a bit with a nice deep scratch and sound effects from that Xacto knife and pretend not to notice. The comment section would be glorious... lol Awesome video !!

Awesome mixer, but what an awesome spectrum analyzer!! Can you do a video on that analyzers internals, digitizing..? I would love to see how that instrument is storing the scans... hmm at that era it had to be expensive in components

Wow!

Tech skills are so cool ! By now you have learned years more, and have built also DIY meter that reaches 15 Ghz ? :)

Customized duplexers, filters, LC filters, power dividers, dual channel filters, design Negotiate prices based on indicators

Can you share the design files for the PLL board. I'd like to build one myself. I use Kicad or Altium designer. Thanks.

How much those devices like the frequency counter, spectrum analyzer, etc cost you for this lab? I want to build one but when i search it cost damn too much so perhaps you could give me an estimate

@stargazer7644

4 жыл бұрын

Microwave stuff isn't cheap. $1k-3k for a cheap surplus HP analyzer that goes to 20 GHz or so. 141T analyzers like he has go for $400-$1000 but are getting pretty old and fussy. $500-$1500 for a microwave counter good to 26 GHz.

Love your videos, your channel is sure to grow if you keep these up. I'm planning to start playing with mixers and learning about them with the plan for making a portable 220 radio with a mixer, lo and one of those Chinese special "FM VHF/UHF HT" boards. With a filter and such ofc. Have you worked with the ADE-1? I bought one on a PCB I'm planning to experiment with using an SDR as the LO. I would love to collaborate with you on a future video if your interested. I have a lot of fun with SDR and your channel hits the spot when it comes to moving to working with the hardware end of radio. If interested you can best contact me on website you'll find linked from my channel page.

It didn't look like there was solder paste on the center pad.

Black magic in the microwave realm! Are you studying Engineering? I’m about to quit… want to play radio …. Quartus Prime FRPGA project presently making me very 😔. Thanks for this content!

Knife as pointer...hmmm...brave...?

That coax cable looks like teflon so velocity factor isn't 0.66.

@stargazer7644

4 жыл бұрын

Odd that the calculation came out correct then, isn't it?

nice video regards pa3dee

@vk2seb

7 жыл бұрын

cheers! glad you enjoyed the video :)

What is the Texas Instruments board that you are using? (Appears to be a TI Lauchpad...?) Maybe like this? www.digikey.com/en/products/detail/texas-instruments/EK-TM4C123GXL/3996736

God someone who speaks English!

@Argosh

6 жыл бұрын

Paul I get an allergic reaction after all the Indian stuff I had to listen to O_o

i have many equations about this can you give me your email please???

get the knife away from hp spectrum analyser