Do not clean the joints in the table, drop something down the hole on top of the F.C. could lead to a bad day, Clean & lubricate the pins / boxes in the V. Door
@geneautry2091
2 ай бұрын
Exactly👍
@alexorlando75333 жыл бұрын
Cross threaded the fuck out of that one lol
@johnknouse8846 Жыл бұрын
Don’t drop that brush!
@bonsaicharlie2718 ай бұрын
I haven’t been a rough neck in almost 10 years but watching them dope the casing in the hole makes me nervous. These guys suck
@Oilcasing3 ай бұрын
good video!
@lktrffcnbvcxse3 ай бұрын
nice!
@jeffmorris7222 Жыл бұрын
I have run up to 14,000 ft on 13 3/8 at the rate this is getting run you guys are going to be at it a week spin that shit up those tongs got high use it if you can't tell it's crossed put someone on them that can
@epistte
7 ай бұрын
Where and what are you drilling that you run 14K of 13 3/8? That is surface casing or the top string of 2 intermediate casing runs. Holy hell.
@seanellis3921 Жыл бұрын
Older Type Rig ??
@benisilva3367Ай бұрын
Hope they got them new bikes on they bout to get ran off
@anthonyedumogiren78316 ай бұрын
Tong operator is good, not easy running 13 3/8 casing without good stabber just side door. Alignment issues must come up..
@split40222 жыл бұрын
Lol he fucking got a shot in his hand.
@cableheadcrew38809 ай бұрын
This is painful to watch
@laplace2282
4 ай бұрын
Why?
@onshore-club7382
4 ай бұрын
why
@ThaGoblin
3 ай бұрын
@@onshore-club7382read the other comments.. then you will see why it is painfull to watch. If this was my crew I would send them all home and get a new one.
@ThaGoblin5 ай бұрын
well that was painfull.
@geneautry20912 ай бұрын
Why don't those worms dope the threads?
@environmentalbill33754 ай бұрын
No thread protector? stabber on top not doing his job
@pedroparamo8164 Жыл бұрын
Es bonita la PERFORACIÓN pero solo en video 😂
@francisgimenez71206 ай бұрын
He should watch the stabber
@marobakrma5 ай бұрын
why there is no backer lock or belzona why not using seize glue no torque tight old model rig
@user-pb4qh5xp6c
3 ай бұрын
They had enough pipe weight where they no longer needed backup tongs. You only use threadlock near the shoe, so you don't unscrew any part of the shoe track during drill-out. Otherwise, threadlock is slow and unnecessary. No "torque turn" because this appears to be buttress thread. It's not a premium thread where you capture a digital graph of the makeup for each joint. You make it up to the triangle. You can see the tong operator looking for the triangle before he quit. It didn't look like he was anywhere close to burying the triangle.
@miguelbolivar76468 ай бұрын
No eso no es hasi.
@gbipit125 күн бұрын
Ridiculous where the Supervisor
@subratadas2974 Жыл бұрын
Bahut slow ho yer aplog... Power tong operator is very 😂 lol...
@user-pb4qh5xp6c3 ай бұрын
Why would anyone post this video of running casing unless you want to show how to fuck up a casing run? 1- Don't wipe the box with the joint in the hole. Clean the boxes while the pipe is on the rack, FFS. 2- They cross threaded the fuck out of this joint. 3- Taking this long to make up joints is a good way to get stuck if any of your pipe is across a permeable zone. Where was the pusher or company man.....beating off or playing Tetris in their trailers?
@mudassarmajeed93522 жыл бұрын
Not a good tong oprater
@sadofficer6 ай бұрын
The worst tong operator ever seen
@kevinbuchan8954 Жыл бұрын
Terrible caser, so slow you'll end up stuck.
@clevaland71952 жыл бұрын
Tong Operator Trash. For 1. He doesn't have a 90. 2. He's not looking up at Elevators to find sweet spot.. .. 3. Why is the guy holding the ropes??
@fhr42929 ай бұрын
Man if this was my crew would be ran the hell off lol especially if a company man saw us box a joint with the tongs locked on the joint wtf this was horrible to watch.
Пікірлер: 39
Do not clean the joints in the table, drop something down the hole on top of the F.C. could lead to a bad day, Clean & lubricate the pins / boxes in the V. Door
@geneautry2091
2 ай бұрын
Exactly👍
Cross threaded the fuck out of that one lol
Don’t drop that brush!
I haven’t been a rough neck in almost 10 years but watching them dope the casing in the hole makes me nervous. These guys suck
good video!
nice!
I have run up to 14,000 ft on 13 3/8 at the rate this is getting run you guys are going to be at it a week spin that shit up those tongs got high use it if you can't tell it's crossed put someone on them that can
@epistte
7 ай бұрын
Where and what are you drilling that you run 14K of 13 3/8? That is surface casing or the top string of 2 intermediate casing runs. Holy hell.
Older Type Rig ??
Hope they got them new bikes on they bout to get ran off
Tong operator is good, not easy running 13 3/8 casing without good stabber just side door. Alignment issues must come up..
Lol he fucking got a shot in his hand.
This is painful to watch
@laplace2282
4 ай бұрын
Why?
@onshore-club7382
4 ай бұрын
why
@ThaGoblin
3 ай бұрын
@@onshore-club7382read the other comments.. then you will see why it is painfull to watch. If this was my crew I would send them all home and get a new one.
well that was painfull.
Why don't those worms dope the threads?
No thread protector? stabber on top not doing his job
Es bonita la PERFORACIÓN pero solo en video 😂
He should watch the stabber
why there is no backer lock or belzona why not using seize glue no torque tight old model rig
@user-pb4qh5xp6c
3 ай бұрын
They had enough pipe weight where they no longer needed backup tongs. You only use threadlock near the shoe, so you don't unscrew any part of the shoe track during drill-out. Otherwise, threadlock is slow and unnecessary. No "torque turn" because this appears to be buttress thread. It's not a premium thread where you capture a digital graph of the makeup for each joint. You make it up to the triangle. You can see the tong operator looking for the triangle before he quit. It didn't look like he was anywhere close to burying the triangle.
No eso no es hasi.
Ridiculous where the Supervisor
Bahut slow ho yer aplog... Power tong operator is very 😂 lol...
Why would anyone post this video of running casing unless you want to show how to fuck up a casing run? 1- Don't wipe the box with the joint in the hole. Clean the boxes while the pipe is on the rack, FFS. 2- They cross threaded the fuck out of this joint. 3- Taking this long to make up joints is a good way to get stuck if any of your pipe is across a permeable zone. Where was the pusher or company man.....beating off or playing Tetris in their trailers?
Not a good tong oprater
The worst tong operator ever seen
Terrible caser, so slow you'll end up stuck.
Tong Operator Trash. For 1. He doesn't have a 90. 2. He's not looking up at Elevators to find sweet spot.. .. 3. Why is the guy holding the ropes??
Man if this was my crew would be ran the hell off lol especially if a company man saw us box a joint with the tongs locked on the joint wtf this was horrible to watch.
No eso no es hasi.
No eso no es hasi.