Warning! You used the same old bolts to secure the injectors. You should always use new bolts, bacause the old ones can never reach the correct torque. I also noticed you didnt use a torque wrench to tighten the bolts. But apart from that, the filming and commentery was brilliantly done. Thank you so much. Regards Mark.

Hi mate, just spent last few days replacing injector seals, as well as other stuff and wanted to thank you as wouldn't have been so sure without your video. Very, very helpful!

@Mad4FrenchCars

2 жыл бұрын

Glad to hear that you done it. Thank you for a nice comment it means a lot to me.

@alkethida7384

2 жыл бұрын

kzread.infoN3a-YYTUgk0

Absolutely great video, every step is fully clear . Extraordenary helpfull ! Thanks a lot an rock on! This work has to be done on our X-Pic 1.6 HDi. All the best for you!

Excellent video im goingvto have a go of mine now i paid £90 per injector last time thanks again

Brilliant video. So much detail. Clearly explained step by step from start to finish. Many thanks for this.

@Mad4FrenchCars

2 жыл бұрын

Hi mate thank you for a nice comment, glad you find it use full.

Excellent very informative and will get the reamer kit advised here from the other comment. Will be doing shortly if all washers and gasket are correct for the year and model Citreon Berlingo I have. Thanks for the video.

So detailed for what I needed. Thank you for sharing!!

Just thought I'd add this. Premature turbo failure can be caused by the injector seals going. Even more reason to do this job. Thanks for the video.

@Mad4FrenchCars

Жыл бұрын

Thank you for your comment. Glad you liked a video

Great content. Getting ready for when mine start leaking

thank you for all information. you are the man I'm learning from

@Mad4FrenchCars

2 жыл бұрын

Its my pleasure mate i hope it helps 👍

Very helpful. Thanks for making the video.

@Mad4FrenchCars

9 ай бұрын

My pleasure mate

Nice work again mate keep it up mad hours you are doing there but when you’re the boss it has to be done ✔️

An excellent video, keep it up! 👍😎

Thank you brother! Just replace my rocket cover gasket. Hope I'm not gonna have oil on engine now!

I know nothing about car engines...but I enjoyed watching that.

@Mad4FrenchCars

2 жыл бұрын

Thank you mate I am glad you liked it.

Great job almost with one Hand, Respect :)

@Mad4FrenchCars

11 ай бұрын

Thank you

Thank you for the video!

Thank you, for a very informative video.

@Mad4FrenchCars

11 ай бұрын

Thank you

Good upload going to do this this weekend

@Mad4FrenchCars

2 жыл бұрын

Thank you mate and good luck

Great video content: however on a volvo 1.6hdi you must take care of what injector came from what cylinder ... volvo injector have 4 different parts code when replacing. Be sure to put the injector back where it came out.

Amazing job! Really clearly explained, thanks so much =)

@Mad4FrenchCars

2 жыл бұрын

My pleasure mate glad you liked it.

@danfall8233

2 жыл бұрын

@@Mad4FrenchCars here's me hoping it is the injector and not the timing chain 😆

@Mad4FrenchCars

2 жыл бұрын

@@danfall8233 best of luck hope is just injector seal

Excellent Excellent video Thanks so much for this

@Mad4FrenchCars

Жыл бұрын

Thank you mate.

super vid, helped me a lot. thank you

@Mad4FrenchCars

2 жыл бұрын

Glad it helped mate. Thank you for watching

I'd recommend tightening the rocket cover evenly and In the recommend sequence. This type of car would be 13Nm torque. Also while the injectors are out it's an idea to clean inside the bore and use a cutter to make a perfect seal with the copper ring 👍

Very usefull well done. So much detail. Clearly explained step by step from start to finish. Many thanks for this.

Hi mate , a couple of things you could of done extra while you had injectors out. change the bolts that hold injectors,as they stretch once used so give wrong torque if used again, I thought cleaning out the injector seat and ports befor injectors go back in, check the leak off pipe for blockage while it was disconnected, I would of loosend the high pressure pipe nuts at the back as well, But thank`s for showing the method

@Mad4FrenchCars

2 жыл бұрын

Hi mate this particular video I was doing in a hurry as that day I was extremely busy. I could have done more but only sticked to what was needed to get it going again as I had to put the car together fast I didn't plan this video I just happen to develop injector seal problem so I thought I might aswell record it as someone still might find it use full.

Excellent many thanx.

great work. Tank you

@Mad4FrenchCars

2 жыл бұрын

Thank you mate.

Great video very informative 👏 done my injectors but got a bit of a problem ive got a hole in my manifold since changing the washers what could cause this?

Perfect video to explain how to, what about the tighten specs and new struds and nuts?

Excellent, thank you

@Mad4FrenchCars

Жыл бұрын

Thank you.

Très très bien ❤😂❤😂❤😂❤🎉🎉🎉🎉❤😂😂😂😂 la seule précision que j ' aime beaucoup merci

very good master

@Mad4FrenchCars

2 жыл бұрын

Thankyou mate i really apreaciate it.

Hi Mad4FrenchCars, Good explanations in your video. You were lucky having no injector blocked - it would had been o horrible job :( I have seen you had injector with oil contamination - this was caused by the injector bolts oil sealant deterioration (HDI engine is known for this strange injector bolts position) I would also: - change injector bolts (HDI injector bolts must always be replaced as the bolt's material is deteriorating in time and the length of the bolt increases). I already had a broken injector bolt and extracting it was a time consuming job. This is why , from time to time, you must re-check that injectors are tightened enough - add oil sealant for each bolt as the HDI injector bolts passes through oil. This is the cause for oil contamination when the sealant is deteriorated (some people mistakes for with diesel contamination) - clean injector bed before placing the injector as the surface should be clean. There are some tools for injector bed cleaning which prevent any pressure loss - always tighten to torque or to angle - respect the same injector position when possible - with the engine started listen to the injectors for knocks - you could recognize an unproperly tightened injector by sound - finally check the injectors with Lexia , not for programming the injector but for verifying ECU correction for each injector(0 should be the best result, with a maximum of +2) - again, you could recognize an unproperly working injector.

Great video.... I have oil coming out of wastegate on the turbo, what would cause this? would injector seals cause crankcase pressure? Having a nightmare trying to get a mobile mechanic out.... Thanks

great video, I've done this myself because of your video but the only injector I have touched, it seems it leaks a bit even with genuine seals. do I have to put new bolts also? those ones stretch?

Thank you

What grease did you use to hold the O-ring?

Did you not ream the head for the new copper washers ?

Hi m8 what size oring is it on the intake pipe that joins to pcv valve (the white part on the pipe )

Never done this before have payed for no1 to be done I will do the rest, do you not need to bleed air out of modem diesels?

Nice video mate, doing mine in the new year , sounds like its chugging lol

@Mad4FrenchCars

2 жыл бұрын

I am just waiting for a 508 1.6 e-hdi to be delivered from auction so it will be more 1.6 videos coming soon.

@markkennedy4872

2 жыл бұрын

@@Mad4FrenchCars did it sound a lit quieter after these seals?

@Mad4FrenchCars

2 жыл бұрын

@@markkennedy4872 yep a whole chugging is gone after replacing seals.

@markkennedy4872

2 жыл бұрын

@@Mad4FrenchCars doing mine today, wish me luck haha i will be referring to this video throughout though

@Mad4FrenchCars

2 жыл бұрын

@@markkennedy4872 good luck mate.

How you managed to clean the mess around the injectors?

When you dont chamfer off and clean in the bottom of the injector seats its more likely to fail again sooner.

Is corteco the oem for the gasket? Any recommanded brands? Is there any point in using sealing paste? Do you know if this is the same as the 1.6/1.5 tdci from ford? Thanks for the awesome video!

@Mad4FrenchCars

2 жыл бұрын

Hi mate I have been told that Cortado is oem equivalent option for gasket in my local auto parts shop, and I believe procedure is a same for 1.6.TDCI in Ford. Sealing paste doesn't do the job on rocker cover gasket as far as I am aware.

Nice job. Looks simple when you know how. I noticed you never used a torque. A bit like be just use feel.

@Mad4FrenchCars

2 жыл бұрын

Thankyou mate i apreaciate a good comment.

@datadogie

2 жыл бұрын

@@Mad4FrenchCars Job Done Thank You. My seals were well bad. I got the impression the last ones were poorly fitted. Checking some other forums I see you should not have to retighten them. But I think I will check them in a month or so.

@Mad4FrenchCars

2 жыл бұрын

@@datadogie well different people will say different things, but i think its good idea to check the tightness of all the nuts after few hundred miles just to be on a safe side. In my experience sometimes after few hundred miles some nuts gets a bit loose. I am not sure why. Anyway i am glad you done it and find video usefull.

Lucky you with injectors,i cannot pull first with 2 ton hidraulic jack how much it stuck inside

Great video. Just wondering what grease you used to keep copper seal on injector instead of falling off? Some people put a bit of oil on crank case seal before fitting. There was a lot of oil in your air pipe to turbo.

@Mad4FrenchCars

Жыл бұрын

The car I was working on was a taxi with I think 240k miles on it. Ya it was a bit dirty but the way I drove it as taxi I think most of cars would crap there pistons out so good old 407 did took any beating I throw at it. I just used a bit of normal grease mate nothing special just to stick it on so it wouldn't fall. Most of the rubber seals is advice not to put any grease on them I normally try to replace any rubber seals without using any grease.

@autisticdrone.

Жыл бұрын

Thank you for your reply, wasn’t sure if there was a particular grease to use.

thank you for reply..what about torque for tocket cover? I hope you will have more than 1000 subscribers. I'm sure because the way you explain and showing technique so amazing.

@Mad4FrenchCars

2 жыл бұрын

Rocker cover is 5 Nm for pretightening and 13Nm for tighten it up i believe. Also you have to kind of start from the midle and work the bolts up towards the sides. Try to make sure it all lands on a gasket as equally as possible.

@Mad4FrenchCars

2 жыл бұрын

People tried to go for as hard as 20Nm on rocker cover bolts and snapped them lol.

It always seems to be the 3rd injector seal that goes! Surely it is some sort of fault with design!

@Mad4FrenchCars

Жыл бұрын

It could potentially be, but I am not aware of it. Design is OK but far from perfect.

Your video was pretty good but you didn’t explain at the end is the fuel system self bleeding or do you have to bleed it manually which I think would’ve helped the video a lot better cause I’m still scratching my head about that bit

@Mad4FrenchCars

Жыл бұрын

If you just keep turning engine over it will start but might take a quite a few times. You can help it out by pressing a prime bulb for a couple of minutes but that is just an option for hdi engines as tdci engines doesn't have a prime bulb so you have to just keep turning the engine over until it starts. It's not gonna take too long as a fuel is already in a fuel filter and pump all the way to fuel rail. So it only gonna need of a few engine turn overs and it should start.

A great video … just what I need. One question is there a seal under that fuel line hex nut ? Thanks

@Mad4FrenchCars

Жыл бұрын

Hi mate there is no seal on them copper High presure fuel supply to injector nuts if that's what you been referring to.

@davepangolin4996

Жыл бұрын

Yes that’s what I mean … I am sure one of mine is leaking but won’t go tighter … maybe it’s the lower seal spitting upwards.. anyway now I know what to do … Thanks

Hi, thanks for uploading the end to end process! Just had another injector go on my 1.6hdi. for one of the tightening studs holding the injector down, I have one that just wiggles and floats around, but with an Allen key, I can't seem to tighten it. It keeps to not be able to grip onto anything. Any tips on this you. You mention you use a Crb7 hex tool? This is no different to the hex Allen key right?

@Mad4FrenchCars

2 жыл бұрын

Hi mate thank you for a comment. In your situation I believe one of the injector studs or a stud nut is spinning in place. I would check a thread on a stud and also inside a nut these do tend to get loose very easily. You are right the hex Allen key is basicly a same thing as Crb 7 tool. As long as the end is flat and size same then it's a same tool. It should do up. Mind you it is recommended to replace all studs every time you change injector seals. I know nobody does but maybe these studs not design to be tighten too many times. Studs also easily snap and then it's a pain to get it out the left over. Hopefully you worked something out let me know. Also if hex key doesn't go inside a nut anymore just grab a stud nut with some pliars from the side and try to do it up like that.

@manw8888

2 жыл бұрын

@@Mad4FrenchCars hi, thanks for the quick reply! Yes indeed the stud nut is just spinning and no longer tightening. The hex tool does still spin the nut but at mentioned, the nuts itself just spins and doesnt grip on anything. Its going into a garage tomorrow so hopefully its not too complex a fix. Really like end to end video from you you though! Super helpful to the community!

@Mad4FrenchCars

2 жыл бұрын

@@manw8888 thank you mate really appreciate it.

HI, With all the oil on the outside of the engine, were you getting burnt oil fumes/gases coming into the cabin?? My exhaust system seem fine.

@Mad4FrenchCars

2 жыл бұрын

I have cleared it all up later same day. I think I basicly jet washed it with a brake cleaner. And I can't remember any fumes or smell.

I watched the video a couple of times, but I didn't see anywhere what the torq value is on those screws on the injectors

excellent job.just one question whats the torque for these nut and screws thank you, i need to do mine with torque

@Mad4FrenchCars

2 жыл бұрын

Hi mate i respect your choise to do yours with torque. So lets start from injector studs incase you decide to change them: pretightening is 5Nm and tightening is 10Nm ( pretightening 0.5daNm and tightening 1daNm) 1dmNm - 10 Nm. Then the tightening nuts wich goes kn the studs and secure injector in place Its a angular tightening 4Nm and 75°or 0.4daNm and 75°. I hope it helps once i hit 1000subscribers i will be able to upload a diagrams which clearly provides all information as the community section will be granted.

Hey buddy ! If you didnt disconnect battery before hand and replaced seals would you have to re code ?

@stephenmunt1624

15 күн бұрын

50% shore it wouldn't effect it. I'd just reset codes after the work is done and scan again for any problems

Hi, watched your video and spent the whole day today doing the job and cleaning stuff. However, now my car won't start, at first the engine was trying to crank but after several unsuccessful attempts, only getting a loud winning noise. Any ideas? Need to press the fuel primer pump right? Anything else?

@Mad4FrenchCars

2 ай бұрын

Battery might gone a bit flat. Priming is a must as there might be some air lock in a fuel system but also if you can get someone with jump leads to connect to your car while you try to start it i think would be good idea or try to spray some easy start in a air intake to help with starting it up once it will fire up it will carry on. As once it fires up then cambelt will turn a fuel pump and should push through any air pocjet

@bensake5590

2 ай бұрын

@@Mad4FrenchCars Thanks for your reply. Charged the battery to 12.6V, pressed the primer pump several times still can't start the engine. Starter motor seems ok, can hear the cranking sound. I just remembered that I've lost one of the metal clips that secure the fuel return line on one of the injectors. Do you think it's possible this could be the reason?

grande perfetto (unico sbaglio non avere pulito il tutto prima di montare gli ignettori)

@Mad4FrenchCars

2 жыл бұрын

ciao amico, grazie per il commento non l'ho pulito tutto maculare perché ho fatto un lavoro in fretta come devo andare al lavoro. Ma mai meno tutto ha funzionato al 100%

Complimenti per il bel lavoro eseguito ,nota solo piccola osservazione :scarsa pulizia dei pezzi smontati è rimontati .

@Mad4FrenchCars

2 жыл бұрын

Ciao amico grazie per il commento. Avevo fretta di portare a termine il lavoro perché avevo bisogno di un'auto veloce. ecco perché è stato solo un rapido riordino ma non una grande pulizia.

I have the same problem on mu mazda 3 2004 . The same motor with bosh injectors is. The 1.6 hdi motor is in volvo,Peugeot,citroen, mazda,ford . When you have s cha chua chua sound you need to replace a seals, but when you have a problem like this,you need to chek injectors and leaking , my 2 injectors have a leak. I have a problem that a 2 injectors have a oxidation and don't want come out, and i need a tool for that on compressor to pull them out .

@Mad4FrenchCars

Жыл бұрын

Sorry to hear mate. Injectors wich doesn't want to come out is common problem. Couple of times I used a compressor tool and injector came out with sleeve so had to use torch gun to burn a soot and then put sleeve back in once is off. It can be a pain sometimes

Hey, loved your video, followed every stepped and i got rid of "chuffin", could swear that engine is not as loud as before too, but I have new issue, on injector 3 and 4 i have slight diesel leak, have I screwed up something ? :D

@Genakrul_93

2 жыл бұрын

The fuel is coming from the top of the injectors, with the old and the new o-rings.

@Mad4FrenchCars

2 жыл бұрын

@@Genakrul_93 hi mate then you say a top of injector, is your injectors different from the ones in a video? It might be a fuel return connector split so ether or a high presure fuel supply bit to injector undone itself then you was undoing it if its a same injectors

@Genakrul_93

2 жыл бұрын

@@Mad4FrenchCars It is fuel return connectors, but thats low pressure and it got me confused why does it leak there now. :D

little question: is there a way to test the injectors of proper working. i measured the resistance with a multimeter at the two pins and it showed around 0.7ohms on all four injectors. is that correct. i dont have any idle problems. thanks.

@Mad4FrenchCars

2 жыл бұрын

Hello mate normally people doing a test at home get a leak off test and test injectors with that. I have not made a video about it yet so I will share a video of someone else doing this test. kzread.info/dash/bejne/lZ6Kpqqsprm0pM4.html

Hi, When you are removing and then return the injector cables back, the computer is necessary to connect them to the system?

@Mad4FrenchCars

2 жыл бұрын

No if you disconnect your battery before you do it then you dont need to use any software to tell your car about it. But if you done this job without disconnecting a battery then you would only need to delete faults redistered by ecu with diagbox. As once you disconnect injector with battery connected ecu will log it as a fault.

@GordonFreeman13377

2 жыл бұрын

@@Mad4FrenchCars thank you so much 🙂

@Mad4FrenchCars

2 жыл бұрын

@@GordonFreeman13377 my pleasure mate

I've done everything you just done the same way but am still getting leaking injectors I've given up and getting someone else Todo it I've been told too change the studs as well that hold the injectors in place and use some rtv silicone gasket maker on the and also around the rocker cover gasket to help stop oil leaking did you sort your issue out ? I need to get my injector seats cut that's what am doing tomorrow ilthe only thing I didn't do was disconnect the battery so now have fault code but been reset now it looks easy but when I still don't work it's crazy I tried 4 times and give up hope my issue is sorted tomorrow

@Mad4FrenchCars

3 жыл бұрын

Hello david in my case everything seem to be ok. Injector studs its a pain to remove as they brake, I dont think thats your problem. Sometims fuel supply is a bit off and can leak or a fuel return on top of inkector it always need new o rings. In very rare cases injector itself has been undone and there is a leak on a side of injector. I cant really tell. Rocker cover gasket usually ok as its self sealing gasket.

@Politia.tiktok

3 жыл бұрын

I can answer to your problem,i have the same engine on a ford and i had the same problem.The issue is that this engine after some time of worn it developes blow by gases inside and this gases,mostly are oil vapors escapes around these black seals under the injectors.The solution is when you mount these seals put rtv silicone under them and the problem will be solved

Excellent video! - pity you didnt actually show the engine running though!!

@Mad4FrenchCars

Жыл бұрын

All I can say is a engine was working like a steam train with seal gone and it was fine after

Mine has oil around the injector pockets not diesel , can’t trace it , do you think it’s rocket cover gasket?

@Mad4FrenchCars

Жыл бұрын

It could be also it could be a injector socket out of place pushing oil out.

Hello, can you tell me if I replace all bad diesel injectors with new, in my engine (Ford Focus 1.6 tdci), will it already improve obvious weak power I feel every day, or does't- perhaps if turbine pump is also demaged (during driving with bad injectors maybe). Does setting new injectors with old pump is good solution with no worries in future? Thanks

@Mad4FrenchCars

2 жыл бұрын

Hello mate how do you know if your injectors are bad? Have you done leak off test or have them tested? Injectors is not a cheapest part so you want to make sure they are deffinatelly the cause of poor performance before you replace them. 1.6tdci has only 90 BHP so it's not a very powerful engine as it is people do upgrades on turbo and injectors from Peugeot 407 1.6hdi wich gives them 110bhp but I personally haven't done it. Turbo might be faulty but most common problem with these engines relating to turbo is either a turbo boost selenoid or actual vaccum pipes coming off or developed some sort of crack in them letting air in. I would check vaccum pipes, get injectors tested wich you can even do yourself with leak off pipes measuring how much diesel comes out of each. That would be cheapest option. Its many components working together in harmony and it could be loads of different issues not just injectors or turbo.

@Mad4FrenchCars

2 жыл бұрын

I would start from vaccum pipes check also from getting maybe car diagnosed with Diagbox it might show you why it's behaving like that

@Propolizei

2 жыл бұрын

@@Mad4FrenchCars thanks mate, actually I' ve done diagnostics in two different services and the result is same -two practically dead injectors and two very weak injectors. So they suggest to replace all four with new. It's costly enough, so I wonder if this intervention will improve power and solve problem, or it can go to scenario: injectors are ok now, but turbine is also damaged, and the engine power is still weak as pre-intervention? Or does replacing bad with new injectors suppose and setting a turbo pump with it, so overall system will be good after that? Thanks

@Mad4FrenchCars

2 жыл бұрын

@@Propolizei I think if you 2 garages both saying a same thing about injectors then it might be the fault. I would just replace injectors mate. Turbo should be fine you can always disconnect air intake of it and see if it's any play in a shaft.

Any suggestions on how to get a stuck injector out mine has alot of carbon built up around it...removed as much as i could but still it wont move.

@Mad4FrenchCars

Жыл бұрын

It's a very big problem once they don't want to come out but still possible. I would first remove as much crap build up as possible then use a injector crack spray around it and leave it for like a day to soak in. If it's injector closest to cambelt then it's hardest as it doesn't have space to spin in place. Other 3 injectors you should be able to spin them around but to do that need to remove inlet manifold and rocker cover and use size 24 spanner from behind to turn it anticlockwise. To make it loose

@thewindowheader

Ай бұрын

Leave to soak in brake cleaner overnight to break down the crap

What is the torque spec for the injector bolts ? Regards

@Mad4FrenchCars

2 жыл бұрын

Hi mate I believe it's 5Nm + 65°

I have oil in my air intake i notice when changing out my injector seals any idea what it could be thanks

@Mad4FrenchCars

2 жыл бұрын

Hi mate it's normal to have some oil inside air intake and also in the intercooler as Hdi engines release oil steam through the breather back in to air intake.

@wackey3455

2 жыл бұрын

Thanks very much

@Mad4FrenchCars

2 жыл бұрын

@@wackey3455 my pleasure mate.

Also I don’t know if you knew one of my injectors of gone which I need to replace but you didn’t specify do you need to code a new injector

@Mad4FrenchCars

Жыл бұрын

Hi Sophie this video is not about a injector replacement on 1.6hdi/tdci, it's about replacing a seals wich wears out and is a common issue on these engines. Therefore there will be no specifying if you need to code a new injectors as I am not talking about it in a video.

I did the job on my ford fiesta 1.6tdci 2006 (same PSA DV6 HDI engine), but it won't turn over, I've tried it several times in short bursts of a couple of seconds - up to 6/7 times but it just won't start - I'm guessing there's air in my fuel line, any advice? the only thing i can think of is to loosen the HP fuel lines to the injectors and then try and crank it a few times to see if the air will come through those high pressure lines, reattach and try to start it? I've seen some vids with Peugeots that have manual fuel bleed pump on the car but as Ford don't include a manual fuel pump as these are supposed to be self bleeding

@Mad4FrenchCars

2 жыл бұрын

You are correct. That's exactly what I would do. Disconnect HP lines or at least loosen hpfuel supply nuts on injectors to get the air out. Turn it over until you see diesel coming out.

@Mad4FrenchCars

2 жыл бұрын

Then reconnect again and it should fire up also make sure all the connectors are connected properly back on including injectors, mass air flow sensor and camshaft one if you disconnect it.

@stevem5483

2 жыл бұрын

​@@Mad4FrenchCars cool thanks for the reply, once I've loosened the HP lines and before I turn over to bleed fuel through - do i need to reconnect the maf before turning over or can i turn it over with reconnecting the maf (to bleed fuel through and air out of the HP lines not to try and start the engine fully)?

@Mad4FrenchCars

2 жыл бұрын

@@stevem5483 becouse you connected a battery already to turn over a car just leave maf sensor connected as if its disconnected it will give a fault. You might get eml if the car starts but that will clear itself after a short drive as it might record a fault for fuel pressure then a HP fuel lines undone. But nothing to worry about as either you can clear it with a diagbox after car runs or it will clear itself after a little while maybe a little trip or two

@stevem5483

2 жыл бұрын

@@Mad4FrenchCars thats great, thanks v v much 👍👍👍

Can i use any silicone hose for the intercooler? where can I buy in colors?

@Mad4FrenchCars

2 жыл бұрын

I have seen people using them but not sure of a suppliers

@CarloLeonKolega

2 жыл бұрын

@@Mad4FrenchCars I have in my country but they are silocon and I doubt they will last, since oil eats silicone. Btw, I have on this engine on my mazda 3, i have camshaft sensor error aparently? Have you had that? And where is located? left front top, below the avs?

@Mad4FrenchCars

2 жыл бұрын

@@CarloLeonKolega camshaft sensor is located on top left corner near the camshaft. It's secured in place by one hext bolt.

@CarloLeonKolega

2 жыл бұрын

@@Mad4FrenchCars merci mon amie

Good job but should have cleaned as you went to check for further leaks

@Mad4FrenchCars

Жыл бұрын

Thank you

All my previous 2.2 and 2.0HDI never had an issue with injector, but the 1.6HDI it looks poor and bad design?

@Mad4FrenchCars

3 жыл бұрын

Maybe you was just lucky not to have an issue with injectors or injectors seals on 2.0hdi as its as common as on a 1.6hdi. Otherwise people wouldnt buy 2.0hdi injectors as soon as you list them. And i have loads of 2.0hdi engines before with messed up injectors especially siements fuel system. Delphi seem to be more solid. 1.6hdi injectors are solid and hardly ever fail but the injector seals do go like every 50-60k miles but it only cost like 12£ and its easy to replace. 2.0hdi only benefit is more power and 6speed gearbox rather then 5 speed gearbox. But there is a loads of things i prefer in 1.6hdi like location of turbo is much better in my opinion also 1.6hdi gearbox much easyer to take of then doing a cluch. 2.0hdi however has a thicker driveshafts wich is better. I run 2 1.6hdi 407s to over 240k miles so i can tell they are solid as long as looked after and also they love good beating. 2.0hdi is good engines to but you cant really say oh 1 is better then other.

@missionnad1

2 жыл бұрын

@@Mad4FrenchCars I have 1.6 hdi , 220.000 km No problem with injector seals

@Mad4FrenchCars

2 жыл бұрын

@@missionnad1 220k km thats 137 miles so ya that mileage is still probably ok. Later then its like 270-300k km will need to change at some point it happen to all of my 1.6hdi

hi mate I stared to take out injector the one on the left. I could not remove the injector.i tried to pull with clamp but no help .any idea ?thank you

@Mad4FrenchCars

2 жыл бұрын

I would recomment to get some injector crack spray. I normally use it if one doesnt want to come out i spray all around it and leave it over night it should come out easy next day as all the carbon around it will get soft.

@TheHamouda

2 жыл бұрын

I have inly carburetor and egr cleaner if it will help?

@Mad4FrenchCars

2 жыл бұрын

@@TheHamouda to be honest mate i think thats prity similar thing so it should help

@TheHamouda

2 жыл бұрын

@@Mad4FrenchCars thank you for reply

@Mad4FrenchCars

2 жыл бұрын

@@TheHamouda my pleasure mate

Similar car 1.6 hdi piccasso c3 2010 I cannot find the oil pressure sensor any ideas

@Mad4FrenchCars

Жыл бұрын

Oil presure sensor normally sits near the bottom of the engine block. You should have a sensor cable going to it aswell. Usually near the place where other end of dipstic tunnel goes in a blovk

@jokerthelegend486

Жыл бұрын

@@Mad4FrenchCars thank you

Got told my rocket cover could be the problem of oil leaking into the turbo is this true?

@Mad4FrenchCars

3 жыл бұрын

It can be if the valve on a breather side is stuck open it would cause a breather to be always blowing more then it should also if you have more then recommended then amount of oil in a engine. Normally you will always have some oil comming from breather to turbo. But if there is a lot of it then might be a good time for service as fresh oil is more thick and will not come from breather that easy.

@Mad4FrenchCars

3 жыл бұрын

Oil comming to turbo from breather is normal if you like to push the car to high revs or if service intervals is not followed then it will start to shit itslf a bit but nothing to worry about performance wise. If you want it to be more tidy you can install catch can

@stephenmunt1624

15 күн бұрын

I've had the same problem. I brought a hole new rocket cover with the gasket seal ect for just £13 on ebay so not too bad priced

I bad this on my car and ended up as a full top end rebuild

Ver good film ,une question? pour démarrer la peugeot il faut coder les injecteurs avec un ordinateur. Seconde question? pour retirer l'admission, il est nécessaire de retirer toute la ligne de carburant. 3 question?, quand on démonte la vanne d'admission d'air il faut la coder par ordinateur. Merci de m'avoir aidé, salutations d'Espagne

@daviddaviddaviddavid2955

2 жыл бұрын

alors dis moi quelque chose s'il te plait

@Mad4FrenchCars

2 жыл бұрын

Merci pour votre commentaire. tout dépend de ce que tu fais avec les injecteurs. si vous obtenez 4 nouveaux injecteurs, vous devrez peut-être les coder avec diagbox. si vous remplacez simplement un joint sur un injecteur existant, tout ce que vous avez à faire est de déconnecter une batterie de voiture avant de déconnecter un injecteur et une fois le travail terminé, connectez la batterie, elle ne devrait afficher aucun défaut. si vous remplacez 1 injecteur et gardez 3 anciens, vous pourriez le coder, je ne suis pas sûr.

@Mad4FrenchCars

2 жыл бұрын

@@daviddaviddaviddavid2955 désolé pour le retard de réponse

@Mad4FrenchCars

2 жыл бұрын

la deuxième question était de savoir s'il était nécessaire de retirer le système de carburant pour retirer le collecteur d'admission d'air, je crois. donc la réponse est que vous auriez besoin de supprimer au moins une alimentation en carburant de la rampe d'injection aux injecteurs car ils se trouvent au-dessus du collecteur d'admission d'air. Vous devez également déplacer une conduite de retour de carburant, mais vous devriez pouvoir le faire avec des injecteurs laissés seuls. De plus, le joint de cache-culbuteurs devrait être retiré car il boulonne un côté du collecteur d'admission.

@Mad4FrenchCars

2 жыл бұрын

la question 3 était je crois que l'admission d'air a été supprimée, vous devez la recoder avec un logiciel ou quelque chose dans ces lignes. la réponse est simple si vous débranchez une batterie de la voiture avant de commencer un travail sur votre voiture. Ensuite, vous pouvez déconnecter tout ce que vous voulez et ce ne sera pas un problème tant que la batterie n'est reconnectée qu'après un travail effectué et que tous les connecteurs sont remis en place comme ils le supposent. si vous déconnectez le capteur de débit d'air massique, les injecteurs ou tout ce qui se passe dans une voiture avec une batterie connectée, il enregistrera un défaut. mais vous pouvez toujours le supprimer avec le logiciel Diagbox

What is the injector removing tool called ?

@Mad4FrenchCars

Жыл бұрын

I think is just call injection puller but the one to use on a delphi injection system is called MasterPro Diesel Injection Puller Set For Boschdelphi Injectors

pourquoi ai-je remplacé la pile par une neuve et la fermeture centralisée s'est déclenchée, au bout de 10 minutes elle ne fonctionne plus... sauf pour 3008-2009... quand la clé avant est insérée dans le contact, elle refonctionne ...

can you take off the injectors without removing the rocker cover? since i just put in a new gasket and sealed it xD

@Mad4FrenchCars

2 жыл бұрын

On 2.0hdi you can on 1.6hdi you still can but its more complicated

@daviddaviddaviddavid2955

2 жыл бұрын

@@Mad4FrenchCars Bref, si je débranche d'abord la batterie, je peux retirer les injecteurs et aussi la valve d'air. Une autre question est de purger les injecteurs ou vous donnez la clé de contact plusieurs fois et c'est ok, un salut merci

@Mad4FrenchCars

2 жыл бұрын

@@daviddaviddaviddavid2955 oui, c'est juste pour purger les injecteurs, vous pouvez le faire manuellement en appuyant sur une pompe de purge noire au-dessus d'un collecteur d'admission d'air ou, comme vous l'avez dit, vous pouvez faire tourner le moteur plusieurs fois.

@daviddaviddaviddavid2955

2 жыл бұрын

@@Mad4FrenchCars je veux changer le caoutchouc des injecteurs je les sors de la culasse, puis je les purge comme tu dis ok. suis espagnol mais je comprends bien je suis avec le traducteur google hahaha

@daviddaviddaviddavid2955

2 жыл бұрын

et pour nettoyer la vanne d'air d'admission, débranchez d'abord la batterie, puis branchez la batterie et elle démarrerait, avec quelques pannes mais pourrait aller à l'atelier, ce qui est peu

Hello...did u forget to use the fuel Pump in the end ???

@Mad4FrenchCars

2 жыл бұрын

What exactly do you mean mate, I have replaced injector seals in this video. If you struggle to start your car after that becouse of a air lock in a fuel system then just undo a fuel supply 17 mm nuts and try to turn it over few times to get rid of air of the system then then you see fuel coming out just do the nuts up and it should start with no problem.

@hugosilva1980

2 жыл бұрын

@@Mad4FrenchCars I have ideia when u take off the injectors, u must use the fuel ruber Pump

@Mad4FrenchCars

2 жыл бұрын

@@hugosilva1980 oh you mean a rubber primer to prime the fuel. Yes you can use that to prime your fuel system. You can just prime it using a rubber pump before putting a fuel return hoses in to a top of injectors. You can do it either way

@hugosilva1980

2 жыл бұрын

@@Mad4FrenchCars that piece at min 3.58 ..sorry my english 😁

@Mad4FrenchCars

2 жыл бұрын

@@hugosilva1980 yep that's the one. It's a rubber fuel primer.

How many kilometers have the car?

@Mad4FrenchCars

2 жыл бұрын

374000km or 234000miles

@missionnad1

2 жыл бұрын

@@Mad4FrenchCars The injectors are original or has been changed ?

@Mad4FrenchCars

2 жыл бұрын

@@missionnad1 same original injectors

It's a decent enough video but very rushed work. You should have checked the injector housing for dirt and cleaned those out to remove any carbon build up with a reamer kit. Chances are you're going to have to do the job all over again.

is that a c5?

@Mad4FrenchCars

Жыл бұрын

A Peugeot 407

@connectlogic

Жыл бұрын

@@Mad4FrenchCars oh OK. Looks the same as a C5. Does this problem cause the car to jerk or stutter when accelerating?

@Mad4FrenchCars

Жыл бұрын

@@connectlogic it can but in a long run seal goes and then engine sounds like a steam train couse diesel and smoke gets pushed out through a seal next to injector.

@connectlogic

Жыл бұрын

@@Mad4FrenchCars OK thanks. I've got 2 or 3 gone. Ill have to book it in to be sorted out.

Hehehe,you remove injectors woth hand and i couldn't move first one with hidraulic pull

@Mad4FrenchCars

8 ай бұрын

Sometimes they do get seized. Injector crack day before the job is always good idea

@Mr11ESSE111

8 ай бұрын

@@Mad4FrenchCars i try for 3 days for 1-2 hours and i manage around 2 .3 milimetar turn it ! i think that previous owner never change seals on it and now it leaks fuel and car losing power or dont want to start so

And the little green seals go where ?

@Mad4FrenchCars

2 жыл бұрын

Little green seals are for a fuel return lines little black plastic connectors, wich goes in to injector

never bend the fuel supply pipelines like that ! it will give you big problems

@himzooglecevac9356

Жыл бұрын

And what if you remove air intake pipes?

@550ronald

Жыл бұрын

@@himzooglecevac9356 shouldn't be a problem, but there is a reason to why these fuel suppleypipes are in metal. the pressure is very high in them, and they are measured presisely to fit - on the mico-millimeter !! leave them alone. loosen them ,but dont remove or bend them

EXCELLENT JOB. VERY WELL EXPLAINED. KINDLY LET US KNOW WHERE TO BUY GOOD QUALITY INJECTOR SEALS KIT FOR Peugeot 3008 2014. 1.6 HDI. Reg (WG64 LUL)

Great video,one of the best on yt 👋👍👌🫡