08 Ford F250 2WD Ball Joints Install
Автокөліктер мен көлік құралдары
Today I’m at the shop doing upper and lower ball joints on a 2008 Ford F-250 2wd sweeper truck! Truck is a work horse and we like to keep them all maintained! I’ll show you how I do it in this video! I’m sure there are other ways but this is my personal way I install them! Tie rods will be coming soon! Stay tuned!
Remember, Love each other!
Edited on iMovie
Audio from iMovie
iPhone 11 & MacBook Pro also used
Пікірлер: 33
I'm about to change my spindle and hub on my 06 f250. It's been many years ago since I've done one, but it wasn't an f250. I searched and searched. All I came across was for 4×4's but I finally found yours 2×4. You were clear and understanding, you did a good step by step, only improvement you could make would be lighting and an adjustable tripod so the camera will be at same height or looking down as you work. 👍
Thank you!!! By far, the best tutorial for F250 2wd ball joint replacement I have ever found.
Nice video, saving for reference in future
This helped me out a lot. Thank you!
You did great 👍. Man, now I gotta do this too. Thanks for the refresher video.
Dude, YOU ARE AWESOME ! I watch a lot of vids, too many guys gotta keep their face in the camera for excessive amount of time so I stop watching them within a couple of minutes. YOU had enough face time to explain the process and then you got busy with the work...minimal face time=terrific content. By the way, can you come do my 08 f250 now ? I am saving your vid for future review, THANK YOU !
Great video. I chucked that tool up in the lathe and removed .100 or so and it worked good. Angle iron was to hard for me to hold. 👍👍👍👍👏👏👏👏 Thanks for video.
Great video, Finishing my coffee so I can go get started on mine. Needed a refresher, and to see if there were any snags I might encounter.Looks pretty straight forward.
Great video, thank you Very helpful and you FF at the right times 👍🏻👍🏻👍🏻
Awesome video man. Gonna do my ball joints this weekend and now I'm confident after watching your video.
Awesome job! We should all think like you do.👊👊🇺🇸🇺🇸
great video !!!!!
Great video but I would recommend torquing down major suspension parts to the proper torque values. But I get it.
Love it.! Thanks
Awesome
Great video! Do you or anyone have a video on the I-beam bushings? About to do those next
Doing this same job today. 2001 f250. Just need to look for a thick steel plate since i have the same HF ball joint tool.
I would like to seee why you did not put the large ball joint on first and press it in with the clamp
Do you have to get the front end alignment after installing both ball joints on a 05 f350 dually or no ??? Thanks
Got anything on changing the tie rods out on this 2wd model? Can’t find any vids.
How much torque the top nut
So, not a big deal with torquing the lower ball joint to 150? I maxxed out my 80 pound torque wrench and was planning on buying a 200 to finish the job.
Hey...friend...from Puerto Rico ..what is the brand of the new balljoint?
I got a question, where did you get the ball joints?
You need more lighting , some areas were dark on the back side. good job.
Does the upper ball joint not have a snap ring?
@hozerdzyou
2 жыл бұрын
no
Thanks about how much time start to finish?
@sparksadventures9140
2 жыл бұрын
Couple hours maybe.
Did this on 4wd, a little different , little harder, more involved.
What happened to the abs sensor wire.???opps
@robertgarrett1130
2 жыл бұрын
Great job, great video. Information that was very helpful.
Yea, if you can't jack up a car, this is NO job for you!