well...THAT video was disappointing....you should have recorded replacing the IPR, and then the final fire up...there's something very satisfying about watching a video where the end result is the truck running well again....

Nice! Glad it fixed it! Heres a good tip I've learned in my day that can be helpful. If you get a spare similar connector. Lengthien the wires to where you can touch them on the battery terminals. Ground the ground and tap the positive to horribly simulate pwm. If you have a good electrical circuit you'll see sparks. If it's dead nothing will happen and you'll have a quick ipr diag!

One of my new favorite channels to watch. I'm wrapping up my 450-500hp 7.3 build, as a matter of fact I'm finishing building my transmission in the morning. One of my new favorite daily KZreadrs, I'm always a fan of the Ford diesel techs that put up videos. Good work! And to answer your question, I like the 7.3 dips tickets over the 6.0 also.

@PowerStrokeTechTalkwARod

7 жыл бұрын

Combined Gaming World thank u thank u. share my vid!! glad u like

Hey brother I watch all your vids. I'm a mechanic don't do diesels but watching your vids you have givin me great advice or plan of attacks when doing jobs that look a lot harder then they are. Long story short love the videos your a very smart technician and love watching and learning when I get out of work, keep them coming brother!

@PowerStrokeTechTalkwARod

7 жыл бұрын

+Dave P DUDE thanks so much!!!!!!!!!!!!!!!!!!!!!!!!

@evdawg7757

Жыл бұрын

I also am a tech with tons of experience on many gas vehicles. I bought a 2003 7.3 leery on being an old diesel and it was intimidated but they're such a simple first diesel. After learning how these platforms work i wish id have learned sooner.

that thing has a skip in it too. you are the mechanic but I think maybe do a compression test to make sure the starting fluid didn't kill a piston

GR8 that u were videoing that check... customer can't deny it now...

I bought my 7.3l with 30k miles on it back in 2002, and it seemed to start showing a loss of power by the time I got it home, 250 miles away. It was 8 quarts low. Put oil in it, and it soon lost all the oil again. Turned out to be faulty injectors. Luckily, I took it to Ford and they covered all new injectors under the factory warranty. It's never left me stranded or had any real problems until now. Right now, I'm pretty sure I have a bad IPR, and my ICP is leaking a tiny bit of oil, but I'm not losing anything close to what a couple of bad injectors can cause. My IPR is showing about 175psi, and this is the second time the truck has just died and won't restart while driving slow or coming to a stop. Similar to a CPS, but that was recently replaced, and my tach still registers rpms. Thanks for the video.

Crazy stuff you see! Unbelievable. I enjoy these vids a lot and they are very informative. Cool to see the life of a diesel tech. Please keep them coming.

@PowerStrokeTechTalkwARod

7 жыл бұрын

+Austen thanks man so much, stay tuned

That why these powerstrokes use 15 QTS of earl in them because its a high pressure oil system to operate the injectors ! Great video man....

@PowerStrokeTechTalkwARod

7 ай бұрын

Yes sir!

I'm impressed with your knowledge and hands-on know how of your work. You're an interesting man.

@PowerStrokeTechTalkwARod

7 жыл бұрын

+auaiao9 impressively interesting

I Got the same truck 4+4 and love the 7.3 old motor but reliable as hell.I got all over half million km still going strong.keep up the good work.

@PowerStrokeTechTalkwARod

7 жыл бұрын

+bud morse thanks!!!!!

@backwoodsgarage8094

3 жыл бұрын

Iv got to say the ol 7🌲 most reliable easy to work on love em so much got 3 of them 95 f350 dulley 2wd 5 speed 97 4x4 auto and 99 f350 supercab 4x4 any time of year all 3 will fire up run great

Hell yea bro another classic video 😎.

I wish mine was that easy! Changed everything still no start!

Any time my 7.3 slightly shudders at idle it's down 2 quarts. I keep Rotella with me all the time. Has a slight leak. This takes many miles to happen btw and is relatively rare it gets there anyway.

@PowerStrokeTechTalkwARod

6 жыл бұрын

Ahh gotcha

ran my truck out of fuel for the first time that was an adventure. People helping me kept asking if it had oil. it had oil just no fuel hahaha

Gotta love the BIG 15QT written in yellow in front of the radiator 😂

thanks man, very helpful. Im having the same problem

my 2000 psd just decided it wont start today. It cranks over great, tach is at 200 or so while cranking over. Guess i will check fuses, and wiring for mice. It was running yesterday, but i parked on the street nose down last night. Today it wont fire up. Never had any issue with it until today. Thanks for the video, its videos like this that that give us a fighting chance, i never knew about the ipr. Guess i will check for fuel bowl fuse too. Thank you for taking the time to make these videos.

@PowerStrokeTechTalkwARod

6 жыл бұрын

No problem, my pleasure to create. Reach out to me if you need trouble shooting advice..

First thing you always check is oil level. If no visual of an oil leak . Then most of the time injector o rings failure. When a 7.3 falls below 7 quarts it will shut down. Not enough to run HPO system. And if they crank on the engine for a long period of time, you de pleat the HPO in the lines and heads. It will then have reprise itself a crank time of about 60 seconds to build pressure back. You can loosen one of the oil rail plugs on the head to help purge alittle faster. He did not crank long enough to rebuild pressure in the system. The engine needs new injector o rings!!!

Where did you get the new ipr valve or who did you order it from and how much did it cost. Thanks

Wow built in self preservation feature 👍

So if you have a friend who has a diesel and they bring it to you with a no start, check the oil! Ah that's funny! Rule if thumb on all my friends vehicles when they bring them to me, is check the fluids, battery & terminals. Then ask them have you had any maintenance done on it right before you brought it to me by anyone who's not a professional? Most of the time is something simple or just routine maintenance. Thanks for sharing. Best Wishes n Blessings. Keith Noneya PS you've got a really nice channel here. Put some of the videos on specific types in some play lists, it makes it easier to find the type of videos we'd like to watch. Ie. PowerStrokes, 6.O's 7.3's, F-Series Suspension's etc.

@PowerStrokeTechTalkwARod

5 жыл бұрын

Thanks so much for the positive A+ feed back. Much appreciated!!

I enjoyed listening to you talk to yourself, ( or "us" ), as you were investigating the problem. Had me laughing at your "owner" questions. Oh, as for dip stick , I'm only familiar with the 7.3. I will tell you that it came in handy one day as a 30 caliper cleaning rod. ;-) My 2000 F250 pickup wouldn't start this morning so I'll be checking some fuses and oil level. I'm thinking I checked it a couple weeks ago. Thanks for the info!

I have the same problem same sound and everything but my oil level hasn't changed at all. Was leaning towards cam sensor but I'm not sure exactly

it holds 15 quarts... glad you're a PRO...

@ericmiranda9725

5 жыл бұрын

AND, YOU USED THE WRONG VISCOSITY OIL..

Great video bro 👌🏾

Wow, that oil that was in there was pretty dark for just a couple thousand miles... I know it turns dark quick but that looked like molasses (what was there anyway). Really sad to see all that starting fluid.

Likely oil dipstick input plug at the oil pan leaking. Or just straight neglect of a psd puckup

i have a 01 7.3 207k. bought the truck from a ranch here in texas, since then ive started making changes which include.. new hpop,new fuel bowl,new tank mod, new valve cover gaskets, new upper wiring harness, new ipr and icp exhaust sensor map sensor,new oem rail fuel pump,im seeing on here that when you have a crank no start the next thing to do is test injectors? if orings are bad would fuel mix in the oil ? also i have 70 psi at fuel bowl could there be something elec happening? the fuel relay behind the radio does it run the fuel pump? and if i did the injector test and found orings bad wouldnt it just to be better to replace the injuectors and cups than just repair old injectors?

And they even had the oil capacity written on the cowl under the hood hahahahaha

Is the motor still in Good shape are bad because it ant have no oil in it

Nice work i enjoyed the video

@PowerStrokeTechTalkwARod

5 жыл бұрын

Thanks so much!!

Craziest thing I ever had happen working on a Diesel, it was a early 2000's Ford f350 with the 7.3 PowerStrokeTurbo Diesel. (Just like the truck in THIS video) Truck would crank forever and start up rough when completely cold and run for a little while and no matter what you do whether you let it sit and idle or rev it up to try and build oil pressure so that the injectors keep firing it would always die out ESP once it started to warm up it dies out and will not start back up until it sits and gets completely cool again. I worked on this truck for a week straight and took pictures of everything I did and actually figured out the problem while I was going through my pictures! I changed the engine oil pump that feeds the high pressure oil pump that drives the injection system I changed the high pressure oil pump the IPR solenoid and it still would not stay running. What ended up being the problem, was THERE WAS A CRACK in the timing cover on the inside where the low pressure oil pump sits, the crack was on the timing cover, on the output circuit/feed where the oil gets pumped up and goes into to the reservoir that feeds the HPOP! The LPOP was pumping oil and the oil pressure was bleeding off (THROUGH THE CRACK) and going back into the crankcase on the inside, and not making it up to the high pressure oil pump and once the engine started to warm up the crack would expand and get bigger and the oil pressure would bleed off faster than the low pressure oil pump could pump! Changed the lower timing cover and now she starts EVERY TIME and she runs like a champ! I took over 500 pictures and I just happened to notice this tiny crack in one of the pictures that I took. I was so happy when we finally figured it out and got the vehicle back to the customer!

@PowerStrokeTechTalkwARod

2 жыл бұрын

Omg........😱😱😱😱😱

@tiredofthetyranny9874

2 жыл бұрын

O NO! I bet this is what is going on with my sons! I noticed the truck was starting to bleed off oil pressure after a few days, that then turned into daily until it stalled in the driveway! Now we got about $2500 in it and still won’t start! New Hpop,Lpop,icp,etc.! Changed everything! Oil pressure kicks right up now while cranking but drops right off when he stops! It’s at a shop and they did every test they know and everything comes back good, they are stumped and letting my son even use their tools to try different stuff so the bill doesn’t go higher! So did you have to pull the engine out?

@PowerStrokeTechTalkwARod

2 жыл бұрын

No

@Bimmerguy88

2 жыл бұрын

@@tiredofthetyranny9874 no sir absolutely not! You have to take the fan the fan shroud the radiator out so you have all the space on the front of the engine and then you can get right on the harmonic balancer bolt! :) Now that crank pulley/ harmonic balancer bolt is a HUGE P.I.T.A! I think God HIMSELF torqued them @ the factory ;) haha! What I used to finally get it off was; a big breaker bar (The bigger and thicker the better!) It was a 3/4 drive and I just used a deep socket for the harmonic balancer bolt (I don't remember what size it was) and I braced the breaker bar against the frame of the truck and use the engine starter to crank the engine and it will crack it loose! Now be careful when you do this you are doing this at your own risk, but make sure you get the breaker bar and the socket locked onto the bolt and get it on there nice and straight and then turn the engine by hand until the breaker bar is against the frame hey you have to pay attention to which way the engine spins when it's rotating because you want to brace the breaker bar on the opposite side of the frame so that when you hit the key to engage the starter the engine will try and turn but the breaker bar stop it and the starter turning the engine with the breaker bar holding the bolt against the frame it will break that bolt loose like nothing! ;) Now you only need to hit the starter for just enough time for it to break the bolt loose and then immediately stop and take the bolt out by hand after that. Once you have check on the boat out and slid the harmonic balancer out off of the crankshaft make sure you don't lose the woodruff key, then take the upper timing cover off and then the lower timing cover off. Once you have taken the lower timing cover off flip it around and down where the crankshaft sticks through the timing cover you will see the veins where the low pressure oil pump lines up to and one of them is the suction side of the oil pump and the other is the discharge side if you clean it up really well and look at it with a light if it is doing what the truck I had was doing, you should see a little hairline crack inside one of those veins. We had to replace the lower timing cover we thought about having it welded but it was aluminum and I had no idea if it would be strong enough yada yada yada, because customer was desperate for his truck back at this point so we just replaced it put everything back together and that bad boy fired right up!

My request: Show how to ohm the glow plugs. I just ordered a set, figuring I'll need them soon enough, but I've actually never diagnosed them. Truck was hard to start when really cold (below 20F), but when I shorted across the GPR, it started much easier, so I replaced it. But it still romps once started, if it's really cold. I'm thinking either injector clearance has worn too tight, need some GP's, or combination of both.

@PowerStrokeTechTalkwARod

7 жыл бұрын

+gr8guitarplayer ill put 1 up. Cld be just gp or some injs. Id test the gps 1st

7.3 all the way. Proud owner of a late 99.

@slomango7927

6 жыл бұрын

Bigjoe ? Me too 👍

@PowerStrokeTechTalkwARod

6 жыл бұрын

+Grocery Getter yepp he got a horn too!

@RX7GSLSEowner

5 жыл бұрын

Me three! 'Cept mine is a 2000.

@mlane1986

5 жыл бұрын

Me too. I have a 99 f350 with the 7.3 and a 6 speed manual

@RX7GSLSEowner

5 жыл бұрын

@@mlane1986 Absolutely! Wouldn't trade my Zf6 for an auto any day of the week.

Looking for help, recommendations, or resources. I have a Ford 1995 7.3 F250 manual with 150,000 miles. I have a starting issue. For the most part it is sporadic and happens when I cut off the truck and try to start it again after 10 or 15 minutes. It will turn off but doesn’t start. If I wait about 30 or 40 minutes it usually starts right up. I have had it not start a couple of time (one of which currently now), after sitting a few days. But for the most part it always starts after it sits for a day or more. The last time it didn’t start after sitting for awhile, it just started again a few days later. Any help tracking down the problem would be greatly appreciated.

@bobbybob5718

2 жыл бұрын

I hope you have found the issue, but if not. I had a VW that had a similar issue with it, I never found the issue but my brother who is a mechanic said it sounded like it was possibly a ground issue. The conversation happened well after the car was gone so I was never able to look into it.

What a shame...one of the few ways 7.3's die young. Owner neglect.

If people took care of their cars like they should, there would only be half as many mechanics!!!!

Love the 7.3 stick...

Don’t know, had my 7.3 coming up on 18 years. She’s had her problems of just normal aging and wear and tear. 168,000 miles on her. She got new headlights and signal lens today. Sporting all sex now. Got lots of new parts coming in just to toughen her up. She’s done her months of setting, we are know that’s not good for them. She’s getting taken care of and on the road again soon. Y’all be safe out there.

My 7.3 is doimg a slow cold start and an almost no hot start. New icp and batteries with a decent starter. Wanna diagnose it before throwing parts at it. Thanks

@PowerStrokeTechTalkwARod

5 жыл бұрын

Gimmie ur email mista

Very informative thank u

What is it with people not checking oil? Even if they haven't changed the oil it's better than no oil at all

By the way very very awesome video

@PowerStrokeTechTalkwARod

7 жыл бұрын

+Brian Skinner thanks skinner!!!!!!!

@brianskinner4328

7 жыл бұрын

Not a problem. Did you find out what was wrong

What was the sensor to the right for the IPR? The silver/aluminum sensor?

@salvatoretripi4145

4 жыл бұрын

ICU

What typically goes wrong with this IPR? Was the solenoid part bad or the valve itself, the part that screws in HPOP?

Did it end up being the IPR? I have the exact symptoms but I know my oil is at the right level

@PowerStrokeTechTalkwARod

6 жыл бұрын

Yes it was!!

How much Costs A diagnostic For a 7.3

Did the ipr fix it? I'm having the same problem with mine

@PowerStrokeTechTalkwARod

7 жыл бұрын

+joe rodriguez u damn right it did

Crazy, I'm not sure why folks don't check there oil, I do it every fill up with fuel and I change my own, as I don't trust anyone else to do so. Hopefully that engine just didn't eat itself up.

My 7.3 E350 will not start unless left plugged in for an hour or more. Can you help me diagnose? It has new gp's, new gp relay, new uvch's and all tests show gp's are in fact getting power.

@PowerStrokeTechTalkwARod

3 жыл бұрын

Powerstroketechtalkwarod@gmail.com sry going to have to pay, to continue...

Which dipstick we like better? I'm gonna guess not many of us have seen both to be able to compare. I personally have no complaints with my 7.3 dipstick, and I see it at every fuel fillup and oil change, and with 293k miles, I've seen it a TON of times. Ok, bout 500 times.

@PowerStrokeTechTalkwARod

7 жыл бұрын

+gr8guitarplayer lol, well if ya did the 6.0 one, you'd prolly like urs better..lol

Hi! I need help with my ford e350 2002 model 7.3 engine. It Suddenly died and no start just cranking. I removed the wire of the ICP and still didnt work. I replaced my IPR with Brandnew IPR and still got nothing. Just cranking and no Start. Thank you!

@PowerStrokeTechTalkwARod

5 жыл бұрын

Try a cam sensor....

I have a 96 7.3 - I'm thinking I need a cpm- cranks , won't start- no wts light and my hydra tuner won't turn on - I checked if the chip was loose it was not - Checked all fuses all good - oil good - I looked around the fuel bowl for any issues that would cause a short - I think cpm is accurate but anything else it could be - both batts read 12v also died while driving

@PowerStrokeTechTalkwARod

5 жыл бұрын

The fuel heater element under ur fuel filter has mostly likely came loose and has shorted out against your fuel bowl. Better recheck them fuses brah

Can anyone recommend quality service for a 2002 FORD E350 7.3L Diesel in Northeastern Pennsylvania ? ( Nov 2019 )

@PowerStrokeTechTalkwARod

4 жыл бұрын

Sry bud, i dont

How on earth do you let a vehicle run out of engine oil and not realize it? this is mind blowing

@jamesb1988

Жыл бұрын

Especially a 7.3... the oil is what fires the injectors.

@youknow9328

Жыл бұрын

Or thru the injectors ..

@jamesb1988

Жыл бұрын

@@youknow9328 fires them, goes through them, Chinese, Japanese, dirty knees look at these. It's all the same, baby.

I have a p0237 on my 2000 7.3 excursion. I have no oil pressure and i chang the ipr valv. No start. Problems happened after rain. If the pcm were damaged the hpop would stil work right? I would still hav oil pressure right? I removed icp sensor and it should of shot oil out when i cranked but nothing. Hpop is bad isnt it? Or did the pcm get shorted?

@tony.getatme6227

5 жыл бұрын

Help me guys. The fusebox was corroded and i changed it, the icm, the glow plugs, the glow plug module changef also, ipr valve and still no start. Just cranks no smoke. Help me man

@PowerStrokeTechTalkwARod

5 жыл бұрын

Your gonna need to get a scanner on it that you can monitor sensor data. No smoke means your injection hasn't start. If your not getting any high pressure oil your gonna need to make sure you have oil in your reservoir from the base engine oil systrm. Make sure you have good power and ground to the IPR valve. Sounds like you have a lot goin on mann.....

Great video! 7 qts of oil. Don't tell them because they probably think they can go another 10k miles.

@PowerStrokeTechTalkwARod

7 жыл бұрын

+Dale Park thanks, no shit right!

Put oil in the hpop reservoir

I could use some help on my 2000 7.3. It is cranking but no start. No smoke, also the tach does not move while cranking. It’s got compression. It got harder and harder to start then suddenly it quit starting

@PowerStrokeTechTalkwARod

4 жыл бұрын

Hmmm. Only way to help is email...

@billygildark4565

4 жыл бұрын

There’s a green 30 amp fuse on the interior fuse panel that when the fuel bowl heater shorts out blows and won’t fire the injectors... Worth a quick check Normally associated with a no wait to start light.

@angelomallozzi7933

Жыл бұрын

​@@billygildark4565o onin I8nno

haven't found any grease ftg 's on my f350 2020 yet how can I find out where they are?

@PowerStrokeTechTalkwARod

3 жыл бұрын

Two front axle shafts. Watch my video from tuesday!!

@TheShappie

3 жыл бұрын

ok ,I will try and find video. Thank you

Did the IPR VALVE CHANGE WORK TO START IT?

@PowerStrokeTechTalkwARod

4 жыл бұрын

Yes

@marcotesta8651

3 жыл бұрын

@@PowerStrokeTechTalkwARod hi my name is MARCO. I have a no-start condition on my 7.3 L I replace the camshaft position sensor IPR it just cranks and cranks I'm trying to keep my battery is full my pressure oil pressure gauge up sure if I have enough what else can it be. It's not icp cause when I disconnect it it sounds different cranking

@PowerStrokeTechTalkwARod

3 жыл бұрын

U need 2 put a scan tool on it, to monitor your sensor data

The most important thing in ANY engine is to have oil, then coolant then gasoline. If you don't have the first two, having gasoline doesn't matter.

@C4soulja

4 жыл бұрын

That's one of the reasons it's hard to grenade a HEUI like the 7.3. It starves the injectors and the dont run. Not a good idea but a bit of a "catastrophic safety"

Hey man, my truck recently brlke down on me. Have replaced the L-POP and the idm. I replaced the icp sensor and the ipr sensor. The truck did run at first and neber died on me again. As soon as i parked it a d shut it off. It wont start again..... any ideas? Thanks for the video man. Very clear, profesional, and helpful. 👌👍

@PowerStrokeTechTalkwARod

6 жыл бұрын

You need 2 contact me, private message me n we can talk

@michaelphillips5025

2 жыл бұрын

Mine did the same. I can't figure it out

I used to work with a guy who would just run his 7.3 till it died in a parking lot, then add oil to it so it would start. Wouldn't get the leak fixed, but i never could get him to understand how this thing actually fires. He swears to this day that it won't run low on oil cause "it's a built in safety feature", and not because it needs oil to fire....

@PowerStrokeTechTalkwARod

2 жыл бұрын

It's not a "built in safety feature" it uses crankcase oil to not only lubricate the internals of the engine but also send that oil up to a high pressure oil pump which provided up too 3800 psi (@WOT) to push the guts of the injectors to spray fuel into the cylinder. No oil, no fuel injection. Gotta make 600 psi b4 the vehicle will start. Watch my fuel injector video...

@poweredbyford87

2 жыл бұрын

@@PowerStrokeTechTalkwARod oh i know, i just could never get him to understand that lol

Why are you using 10w30 diesel run on 15w40 specially 7.3 and 6.0

@randomgooglename

5 жыл бұрын

does it really matter what oil you put in during diag when the customer is running it 8 qts low? lol

@erics9799

4 жыл бұрын

Alot of people run 10w30 in colder climates for better cold weather starts .

how can I prevent head gasket blown on 6.0l ps if I ever had one? No tuner, and do proper maintenace??? But i knewcoolant very sensitive to head gasket?

@PowerStrokeTechTalkwARod

9 ай бұрын

The head bolts are what stretches and cause coolant to blow out of the bottle

@deepaklopez7436

9 ай бұрын

@@PowerStrokeTechTalkwARod hmmmm, okay is there anyhting to prevent that like maintenace yearly and keep eyes on coolant bottle plus stay stock all the time?

Notice someone wrote 15qt on the front cover there to like remind them it takes a bit more than 5. 😉

@PowerStrokeTechTalkwARod

4 жыл бұрын

Hahaha

I have a 1997 powerstroke it will only start with starting fluid what can be the problem

@PowerStrokeTechTalkwARod

6 жыл бұрын

Lots of things....

people like that = job security for us...

Do you know if a newer 7.3 ipr valve would work on my 94.5 7.3? Thanks in advance👍

@PowerStrokeTechTalkwARod

3 жыл бұрын

Probably not but its worth a shot

@adriannxracrrmorones7168

3 жыл бұрын

@@PowerStrokeTechTalkwARod thanks

Have you done a video on what modules, etc are reset, need to be reset, etc. when a 2017+ looses power (both batteries disconnected)?

@PowerStrokeTechTalkwARod

2 жыл бұрын

None

@zfilmmaker

2 жыл бұрын

@@PowerStrokeTechTalkwARod thanks for the response. I upgraded to X2 AGM’s one at a time and only had half power, no start. Called dealer and service told me disconnecting both batteries would lockup several modules and sensors but as a last resort I did it anyway and was able to start the truck.

@PowerStrokeTechTalkwARod

2 жыл бұрын

👌

Need help bad changed all 8 injectors rebuild ones new valve cover gasket and harness but truck still has problem run it 15 miles or so and it stalls when rpms drop to turn or stop but cranks right back up but have to keep rpms up to 15 hundred and it smokes out tail pipe what could it be had a ICP code but replaced it with a new one from Ford any help would be appreciated thank you

@kenhews331

5 жыл бұрын

Any help would be appreciated thank you

@PowerStrokeTechTalkwARod

5 жыл бұрын

Hey bud thanks for watchin. Have you check fuel pressure when all this occurs?

@kenhews331

5 жыл бұрын

@@PowerStrokeTechTalkwARod no we have checked a lot of things but not that it's coming a bad storm right now we will check it out tomorrow and I'll let you know thanks for the reply i really like your videos keep up the good work

@kenhews331

5 жыл бұрын

@@PowerStrokeTechTalkwARod it's been about a month ago and I finally got the fuel pressure checked and with key on shows about 36 psi running at idle around 38 psi that's with the blue spring update and with 2500 hundred rpms dropped to 35 and came back up slowly to 38 psi would it be possibly the fuel pump thank you

@PowerStrokeTechTalkwARod

5 жыл бұрын

Yes, tooo low.....

I have a 7.3l powerstroke 1997 and i think d IPR is not working Changing the IPR solve your problem??

@PowerStrokeTechTalkwARod

6 жыл бұрын

Yea!

@PowerStrokeTechTalkwARod

6 жыл бұрын

That oldie might need the fuel lift pump in the valley. Have done many of them on your style/yr truck for that reason.

good information,

@PowerStrokeTechTalkwARod

5 жыл бұрын

Thanks bud

My 1996 7.3 psd with 250k miles. Stock. Have a intermittent crank no start problem. My scangauge shows ICP=0 when cranking. IPR 14.8 at key ON. it has no oil on the stock ICP sensor connector. When it doess start it has good ICP and IPR Readings but can have a rough idle with the Engine shaking a bit. the sensors are so expensive and take several weeks to ship to my country so i don´t know if i should order a ICP or IPR... I have a spare CPS sensor but i don´t Think it´s a bad CPS. Shows no CEL or No codes. Passes injector Buzz test.

@PowerStrokeTechTalkwARod

5 жыл бұрын

Probably an IPR but be4 u buy check the oil reservoir and be sure it is full. If not IPR is not ur problemo...

@estranged85

5 жыл бұрын

@@PowerStrokeTechTalkwARod thanks I'll check the reservoir

I know this is old but I have a question about the 7.3. It starts and runs rough then dies you can start it again and it runs fine…sticky ipr?

@PowerStrokeTechTalkwARod

2 ай бұрын

Probably not...

@adamtaylor5711

2 ай бұрын

I have a clip from for scan if you can look at it.

You need 500psi for it to start.

What about adding oil to the top reservoir?

@PowerStrokeTechTalkwARod

3 жыл бұрын

What about it

@whatworksforme5749

3 жыл бұрын

@@PowerStrokeTechTalkwARod 1st Im not a mechanic just a fan. I was just wondering if that would've built pressure sooner for the injectors. the only thing I think I know about the top reservoir is that that is the supply is used for the injection system. So would that have helped in any way?

What was the fix?

If someone had an aftermarket tune and had removed emissions equipment, could you still troubleshoot the engine? I use EFILive which will read codes, but your PC seems to do much more diverse/indepth troubleshooting. Also, in a previous video you had to program misc parts through the ECM, I believe. Can that be done with an aftermarket tune installed? TIA

@PowerStrokeTechTalkwARod

7 жыл бұрын

+Allen Baker yes i can still troubleshoot the electronic engine controls. The computer program I use is Ford only. Can not do other manufacturers. Yes it is very in depth. As long as I work at the dealer, I will NEVER buy a scan tool. This is the 1 you want if your Ford only. Lastly, no. You have a tune, i can not program any modules.....or ones i should say that have anything to do with the engine. It will wipe ur special program out and then my friend ur S O L....

@AJ-di3xd

7 жыл бұрын

PowerStroke Tech Talk w/ARod Good to know. Thank you for your quick reply!!

@PowerStrokeTechTalkwARod

7 жыл бұрын

Allen Baker no sweat, its what i do!!

My truck has a problem, the HPOP reservoir leaks everything through the HPOP, i was told it could be the IPR valve. Could be the pump itself ?

@PowerStrokeTechTalkwARod

Жыл бұрын

IPR no, that just regulates what comes out of the pump

@Blinker_Fluid_Supply

Жыл бұрын

@@PowerStrokeTechTalkwARod thanks for your reply, i will look at rebuilding or getting a new pump

I was gonna say that my dipstick in my 6.7 is made possible because Ford doesn't use speedometer cables anymore and they had to use the inventory for something:)

@PowerStrokeTechTalkwARod

7 жыл бұрын

+Dale Park lmaooooooooo

that's crazy that you put 7qts of oil in that! also cool how you oil in from that hose! and people shouldn't own a vehicle if they don't know how to check basic stuff like oil and filters! smh

Got a 7.3 to and it will start and then die what could that be and I checked the oil lol

What scan tool do you recommend on these?

@PowerStrokeTechTalkwARod

Жыл бұрын

Xtool, launch, think diag, forscan

It looks like it's low on coolant as well

What diagnostic software you running?

@PowerStrokeTechTalkwARod

3 жыл бұрын

Fords IDS

I have a 2000 Ford f350 and it has oil in the water cooler. What can it be

@PowerStrokeTechTalkwARod

6 жыл бұрын

Private message me and we'll talk

@PowerStrokeTechTalkwARod

6 жыл бұрын

Hey hello

@PowerStrokeTechTalkwARod

6 жыл бұрын

Could be man, but sounds like you need more diagnosis

Sounds like a compression skip when you crank it too

@Rift45

3 жыл бұрын

They kill a piston with ether maybe

Suscribed and shared by the way

@PowerStrokeTechTalkwARod

6 жыл бұрын

Thanks so much, private messsage me bro

@ricardogallardo3841

6 жыл бұрын

PowerStroke Tech Talk w/ARod how do i do that? And thanks for.the reply

@PowerStrokeTechTalkwARod

6 жыл бұрын

Goto my channel, request the desktop version if your on your phone, look for About under my channel Art. Private message is in there

I really like how you always include the mileage of the vehicle you're working on. Being a "gasser" guy for most of my driving history, I'm always amazed how you're never surprised by some of the high miles on many of the Diesel engines. Can you let your viewers know an average of "number of miles" you've seen on the majority of the Diesel engines you work on? Also, what is the most you've seen? Thanks!

@PowerStrokeTechTalkwARod

7 жыл бұрын

+Gip Giper i usually ALWAYS have something between 110 and 180....mostly always. Got a lot high ones too...200ks for sure. Had 2 put an injector in a 6.0, 06 i think from Arizona.....875k miles. Got a 6.7 rollin around somewheres with 475k, deleted everything. Always in 4 maint!

@PowerStrokeTechTalkwARod

7 жыл бұрын

+Gip Giper thanks thanks too!!!

I can't believe the donkey didn't even check the oil level before the truck went in. That's embarrassing.

@gratefulhead2833

5 жыл бұрын

Helped him narrow it down!

is IPR same on a 6.0!

So you don't show the fixes? That's unexpected. Really like your presentation and diagnostic process, but would have loved the satisfaction of seeing the motor spark into life.

@PowerStrokeTechTalkwARod

Жыл бұрын

Maybe you can get your thrillz from another one of our shows. 🙋‍♂️🙋‍♂️ What you see is what we had time alotted for

Sorry about venting. It just urks me when there's lack of maintenance

Thank god these shut down when oil is low

@PowerStrokeTechTalkwARod

6 жыл бұрын

Yepp

I have a 2000 F-250 7.3 had service engine soon light came on and it started running roughly and i had the same system before and it was the uvch came unplugged my son put 8 new rebuild injectors in and replaced the value cover gasket and harness and it didn't help at all the service engine soon light was still on and it still running roughly with like a injector knock and i still ran the truck and it completely quite and won't crank back and it's trowing code p0603,p1316,po340,po470 and p1264 and p1277 what could be wrong

@PowerStrokeTechTalkwARod

5 жыл бұрын

Gosh man we wld have to go thru the diagnostic flow charts. Thats a lot of codes to have..

@kenhews331

5 жыл бұрын

@@PowerStrokeTechTalkwARod someone says it could be a bad IDM or PCM does that sound right

@PowerStrokeTechTalkwARod

5 жыл бұрын

Yes it does, you wld have to do the appropriate tests to determine which it is...

@kenhews331

5 жыл бұрын

@@PowerStrokeTechTalkwARod okay thank you very much for responding to my messages

@PowerStrokeTechTalkwARod

5 жыл бұрын

Cld b

On the top cowl at the front it shows 15Qts in yellow paint!

@PowerStrokeTechTalkwARod

2 жыл бұрын

Ok

10:47 "I know I have a... bunch of SQUEAK!!!