Just want to say thank you. I am 600 miles from home with a camper on the truck and pulling a trailer. I stopped at the Salton Sea in California to go kayaking at sunset and afterwards the truck would crank but no start. I found your video and went through the list. The Injector Pressure Regulator coil measured at 400k ohms and it should be about 10 ohms. I slept right there and this morning I used my dual sport motorcycle to go to Napa, 22 miles away. They had a new Napa brand IPR in stock (for the bargain price of only $360). I swapped in the new coil and she started right up. I'm about to chooch home but had to thank you first.

@CUSTOMWORKS7.3PSD

Жыл бұрын

This is fantastic And why I started doing this So everyone can actually fix there trucks

@nippl3johannes148

Жыл бұрын

phenomenal you troubleshooted so well what a great job

Clint, I used reverse Physcalogy on the wife to get the approval to fix up my 2000 F-250 Ole Big Blue... told her the old truck, which I love, needed $5 grand in service work, of course I got a NO!... So I brought home a 2022 F-250 on a test drive and she seen the $84K price tag and said 'Take it back and fix your old dam truck :) Money problem solved 😎

@Just_Wanna_Drive

Жыл бұрын

😂😂

@richardc7721

Жыл бұрын

My wife loves older stuff, that's good for me, we got rid of our new generation vehicles and went back to older units. Her's which she found, is a 2000 F250 4wd F250 7.3 Mine is a 2002 F450, 7.3 Love the 7.3s

@danielmcqueen1024

Жыл бұрын

@@richardc7721 Yeah, my wife's likes her old stuff too... guess after 36 years of marriage I'm a Keeper :) She hates car or truck payments and, well Big Blue is paid off. I actually drove a 1971 2 door LTD from 1984 till 1998! I also back in the Day, drove OTR with Real trucks last one was 1978 Peterbuit 379 w/ 440 Cummins and an 18 speed, What we used to call a 'Large Car' :) The 99' to 02' 7.3 Super Duty is the Best truck made! 1968 to 1972 F-Series is hard to beat! SDs Kinda pain to work on which is rare if you take care them. I got International A/C injectors installed in 2003 with all Banks parts, intercooler, strait thru exhaust... and that increased my fuel mileage from 12 to 18mpgs! All these diesels with emissions-DEF crap takes the life out of very expensive motors.

@richardc7721

Жыл бұрын

@@danielmcqueen1024 it sure has. We had a 2012 F350 6.7. Gave good service until 2020 when fuel issues took out the CP4 pump and injectors. $13,000 90 days later went again. Got rid of it. Now I have a 2002 F450 7.3. Wife's is a 2000 7.3 Best and biggest diesel engine put in a pu from the factory. Nobody makes Better than Banks.

@danielmcqueen1024

Жыл бұрын

@@richardc7721 Sorry to hear the issues with the 2012! That sucks... The 6.7 is a great motor... only if it's been EGR Deleted! And always have a good source of Diesel. I have always used Cumins Power Service to keep the fuel system clean as well as a good Cetane booster! So who has the Lariat trim?? The Wife or on the F450?? Mine is a F-250 7.3 4X4 Lariat that I do all of the work on, grew up in the trucking business so I started working in the shop at age of 10 as a Gofer and worked my way up! Drove for 16 years and quit to be home to watch my children grow-up. So I do all my own work on my trucks and cars... nobody can find an good shop to trust! Plus I know what's been done on repars, nobody but me to blame if it goes wrong! kzread.info/dash/bejne/iZ2dlMGDqsu1c8Y.html

Thank you for all the information that you’ve learned with the years and sharing some of your knowledge. Also adding the quote “I’m not going to tell you everything I want you to know your truck” that makes me want to get in it even more! Thanks a lot for pointing out the most regular problems and for sharing. Again! I really appreciate these videos.

Thanks for uploading these.. You've made me think about preventative maintenance I've ignored for years.. Always great full of talented people sharing their knowledge..

Wow. Great experience and information on the 7.3. Much appreciate you producing this series!

This channel is so good I'm watching videos about issues I've had in the past and resolved just to see how well he explains it and if I had this video alone a few years ago I could have atleast 10 hours of my life back I wasted trying to compare different videos etc. I've had my 7.3 since 2013, If you are kinda new to the game there's no need to look any further, this is the best channel .

Mr.Allen, thank you for teaching us your wisdom on the old girls. Saving your videos for my kids when they get my 10/99 Lariat 7.3 crew cab long bed automatic. As of today it has 15,120 original miles on her.

TONS of great content here! I like every single video I watch. 👍🏻

Man, where have you been all my life!! Absolutely love the delivery, and I love to learn. Pulled out my fuses 1 at a time, checked them and put them back in, because I couldn’t figure out which fuse controlled my mileage and temperature gauge. Truck hasn’t started since!! I’m just going to change out the sensors, change the filters and oil, and clean up the engine !! I’m not sure the original owner ever lifted the hood. I needed this video Thank You

Clint is my 7.3 Encyclopedia. Thank you. 😊

2 years ago I ran TS6 chip with custom tunes for my BTS transmission. Which made it a completely better truck. But I had a problem with it on a intermittent issue which felt like dropping 1/2 the cylinders. I had previously had the L. Valve cover off and fixed a bad plug connection so I was familiar with that issue. Being in south texas for the winter I found a old farm shop that was able to read the 7.3 codes. It took a while but after removing the chip the problem was gone along with the needed HP to pull our 5th wheel. BTS programed a new chip and sent it to me at no charge . Before heading south i decided to replace the valve cover gaskets and wire harness this year . Even though the truck was running good . The harness plug was loose under the R. valve . And also replaced the glow plugs. Money well spent. You talked about replace all the sensors, I wish some reputable business had a package with all the sensors at a reasonable price. I've replaced the ICP sensor so I know they are expensive. On a 01 7.3 ,186k miles. Thanks again for the great info.

LOL'd at the homage to Ferris Buller at the end. Trying the trick of disconnecting the ICP tomorrow, as well as removing it to check the IPR. Already swapped out the fuel filter and Cam sensor. Been down a couple weeks now and it's annoying taking the bus. Had the '95 F250 out here on the Big Island going on 5 years now and just had my first piece rust off last month...

Very comprehensive video. Old guy with a 1997 F-250 CA emissions, 120 k miles. Never had any expensive problems since 1997. Just crank sensors and (1) IPR change. Had an issue popping up this winter. cut out, no start. Think it was water in fuel issue. Thank You for helping. I'm locked on to your videos.

Good afternoon I love this video I learned a lot of information about my truck keep up the great work you do to educate us have a great day

Thanks for the video, it helped me get mine going. I pulled fuel filter and cranked it over to see if I got fuel and the damn thing started lol. so that was easy to figure out.

This is some good info, starting to learn how this trucks run. Thank you very much.

Your video is a library of knowledge..thanks so much for brake I it down for us who are not mechanic but own a 7.3

I bought a 97 that supposedly ran out of fuel and sat for many years as it was running and died, started back up and went a block and never ran again. When I got it. I put new batteries in it, was cranking it over to get fuel up and the IDM blew up so I bought another one, ran the scanner on it and the injectors cycled. The hvop reservoir was empty so I filled it up and it drained immediately, I'm not getting oil into reservoir from lpop even after cranking several times, haven't checked the check valve yet but suspect injectors might need rebuilt one I get oil into the hvop. Your videos are a great source of information as I'm an ASE Master tech, not real familiar with the 7.3 other than is over built for passenger trucks. Mine has 275000 miles on it and going to get a million more out of it.

Wow! I am super impressed ! This is the first time I ever hit the subscribe button.

@CUSTOMWORKS7.3PSD

Жыл бұрын

7.3 SENSOR VIDEO PLAY LIST kzread.info/head/PLDuGIE... 7.3 POWERSTROKE TECH TALK PLAY LIST kzread.info?list... 7.3 POWERSTROKE HANDS ON PLAYLIST kzread.info?list... 7.3 POWERSTROKE TECH VIDEOS AND DEBUNKING PLAYLIST kzread.info?list... 7.3 PSD HOT NO START kzread.info/dash/bejne/jH5ppLV7nte6qqQ.html 7.3 PSD CCV MOD FINALLY DEBUNKED kzread.info/dash/bejne/g6uupZqgXZPVZqg.html 11 7.3 POWERSTROKE ISSUES STOP IN AND SEE COMMON FAULTS......... kzread.info/dash/bejne/aqKZzbWyfduvXc4.html 7.3 POWERSTROKE HPOP OIL CHANGE FINALLY DEBUNKED SEE WHY YOU ARE WASTING YOUR TIME ................ kzread.info/dash/bejne/fImJvMOqgJfPe7A.html

Thanks for what you do! Your videos have helped me greatly to keep my 7.3 running strong! She just hit 1,100,000 miles!

Thank You ! for an Awesome Info on the best Diesel Ever Made Very much appreciated

Thank you! You’re a saint! 🙌🏼

Really appreciate the good advice, hopefully it’ll help me get mine started

Like the 7.3 video's 👍

great video, lots of good info really appreciate it. just came across your channel. Thank you

Thank you for all the great info

Oh hey Clint I'd like to see a video on "Tools needed for working on a 7.3L". I haven't really seen any videos on that and it would be nice if someone like you with the experience and knowledge would show us what it takes. Some simple tools for us driveway mechanics and some more professional tools for those who can afford them. Obviously the Bluetooth OBD II and suggested Software to run with it. Maybe some Compression testing tools and tips etc. Best Wishes & Blessings. Keith Noneya

@sirseven3

Жыл бұрын

1 1/8 inch socket for ICP sensor. 10mm short and deep sockets for the pcm. Idm and engine harness. 13 mm short socket and deep socket for valve cover bolts and studs, starter relay. Odb2 adapter paired with torque pro. 8 mm for the injector hold down bolts. Car Guage pro for pcm idm tests torque pro can't do. One thing I would recommend is using an old valve cover gasket connector and splice them into test terminals you can hook a voltmeter up to in order to test the resistance of all the injector solenoids and glow plugs. Just ensure the gasket is good to go or else it'll throw off readings. 1 inch deep socket with 4 inch extension 1/2 in ratchet for manually turning crank. For compression testing you can remove the glow plug for either cylinder and find something with a 5/16 thread and a 10mm nut like a brass plumbing fitting that connects to a vacuum gauge for compression testing since the glow plug goes in the top of the cylinder/head. For fuel pressure you can buy a 1/8 npt fitting from riffraff or Amazon for gauging fuel easily from the bowl.

Great video as usual thanks for the info God bless

Clint you’re the GOAT

Found a 97 fsuperduty 7.3 power stroke in a junk yard I bought it they said it had a bad engine come to find out the ipr valve was bad it cranked right up love your videos thanks for making them

@Roger_Rabbit_Adventures

Жыл бұрын

👍

@primoisrael

5 ай бұрын

Nice

Great info as always. I do miss some of my old favorite music after the meat n tators, but wonderful content brother. Be safe.

Outstanding video!

Thank you very much for helping 😁

Thank god you're very informant you are the greatest thank you so much

First time on your channel.great info all solid advice .im struggling a bit with one of these monsters .im sure ill get it straightened out following your advice

Lol the ending was great.

Thank you , for all the info. 1999 F 350 7.3L duality with 183,000 miles I’m starting to change all sensors.

@whosdyl9232

5 ай бұрын

What was your issue?

Just wanna you are very very very smart guy , love your videos and I just bought a used 2003 f350 7.3. Not running of course is how I get such a steep discount of 2k to buy it And hopefully soon be running strong with all your info. I have personally wrote down your punch list. Thank you !! For a very very good video and many more I’m going to watch. Thank you again !! From Shawn ❤

Thank you sir for this tech video. I'll be sure to give you the biggest mention after I get my barn find fired up

High Clint. I came across your site not too long ago and am loving the info you put out. I feel that you don't talk the bs that other sites I have seen (like the shady Mechanics you have said). Anyway, my wife and I are looking around on FB marketplace to get a truck that people say won't start and they don't have the time to trouble shoot. I am a Disabled Vet and My wife is Going to school to become a certified Heavy diesel mechanic because that is what she was when she was in the Navy. For we want to start up a mobile diesel repair to help out the loggers and farmers where we live and help other, we want to get one of the 7.3 Trucks and get it fixed and either flip it or give to our son for he is going to become an electrician and will want a service truck. So, buy watching this video we nowhere to start and not go from b to z to a trouble shooting. So, keep the videos coming so we can learn and like you said be able to stuff yourself like you always say and not rely on someone else doing it for you. Now for my wife and I to get money put together and find a truck and get it fixed. You have a great day. and we will do the same. Sincerely Brad and Becky

@squidsmobilerepair

8 ай бұрын

Well, I was just talking with my sister. they have a 2000 f 550 with the 7.3l. My brother-in-law and sister say they are having run ability issues with it and other stuff. They said they want us to work on it and my sister says she wants to get rid of it because they have hardly used in it in the last two years. So, it looks like we have our vehicle, and we will turn that into our mobile repair vehicle my sister just wants to really get it off her insurance for it mainly just sits and does nothing. We will go over it with a fine-tooth comb and do all the checks you say to do Clint and replace what needs to be changed. Again, keep up the excellent videos and we will keep you apprised on our adventure. Thanks for your time. And always to everyone who reads this have a great day and stay safe. Sincerely Brad and Becky

Great information; thanks for sharing.

@CUSTOMWORKS7.3PSD

Жыл бұрын

You bet!

I actually don't know what or what I should or can say besides thank you so much I'm thinking that some of what you covered will apply to 88 gas 150 that just shut down mainly in the wiring area , my 7.3 had well over four hundred thousand miles and died with a sudden coolant into oil you may have been able to help me avoid that but I have have a replacement with three hundred thousand but I was told it runs good and now I know what I need to do to keep it going I'm getting ready to swap it out. Thank you again.

Thank you for the helpful info

I support this content.

Clint is the man!! I get ripped and can't stop laughing anytime he says BOOM!!

good video my friends I’ have a 7.3 2001 F350 nice from Guatemala 🇬🇹 bless America 🇺🇸

This is awesome. Thank you so much

My 2000 F-250 Control Module is located in the cab behind the E-Brake pedal! Where it was easy to plug-in my 6 stage TS Power Chip 😂🤣😎

Thank you for information

For something like an ICP or alternator, I actually go with a parts store part with a lifetime warranty. Only because I can pull in and swap it in a few minutes and if there is an issue I can unplug the ICP and get to the store.

great vid thanks for the list ill let u know know how it goes

for me it was the 6 position chip installed 3 or four owners ago... Thanks!

Clint, I'm a diesel tech, my shop sells Stanadyne fuel supplements and I highly recommend that product.

👍👍👍👍👍👍👍👍👍👍👍👍👍 As always very informative and educational 😊😊😊😊😊😊😊😊

Hey guys hope all is well with you and your family's, my question is what are the normal pids to have on for diagnostic 7.3 econoline van. I'm new to this and I find it interesting. I have forscan lite. It's a 1998 it started running when it was cold but when it warmed up it lost power while pressing the gas. I haven't bothered it in a while so I have to get it back started when I do what should be the first thing to do. Thanks again so much

Wish you had a 05 6.0 crank no cold start video.. I'll have to apply your 7.3 wisdon to my 6.0. Thanks for a great video..

@CUSTOMWORKS7.3PSD

Жыл бұрын

majority of what is talked about will apply to a 6.0 you have the added benefit of monitoring a lot more PIDs on that year with a good scan tool

great video

Thank you

Nice video, better than those computer damn videos that I don’t even understand,

Just had a no start due to battery cables not making good enough contact. Cleaned them up and fired right up. Will be getting a new harness here soon.

Thanks you much sir.

Great watching

thank you

nice work

Good information

I have a 2001 7.3 excursion that was repeatedly blowing the pcm fuse. J-case 20A fuse #113 in my case. I found a short in EOT sensor harness, and after repairing that it stopped blowing fuses. Now I have a no start again. P1210, and po231

01 only starts with starter fluid, 1st diesel great info

Nice content. Thanks. I have 0 experience with the F250 7.3. But since I just bought a police impound machine at auction I have to get it running and driving. 34:33 With 0 history known I was looking for the proper sequence of Trouble shooting. Did not have any idea where to start. Now I do. My 2 cents.

Hey. Great videos!! Can you please list a sample of “reputable diesel site” sources for wiring harness and other parts?

@CUSTOMWORKS7.3PSD

Жыл бұрын

I'm doing a video on this as soon as I get some commitment to quality back from the builders for now always yake a look at riff raff good company

I have enjoyed your videos, very informational ! You say the engine wire harness should be replaced under normal maintenance . Where do I find a new harness? Ford says they are obsolete! I have a 2000 E350 7.3 powerstroke.

@MikeConner.akaRadio

2 ай бұрын

Were you able to find someone who sells the harness, like you said Ford has stoped making them anymore

Thanks!

@CUSTOMWORKS7.3PSD

5 күн бұрын

THANK YOU VERY MUCH

He is right. I've been a diesel mech for 30plus yrs.

@CUSTOMWORKS7.3PSD

Жыл бұрын

Thanks always helps getting a boost from a pro like you !

@nowere4579

Жыл бұрын

@@CUSTOMWORKS7.3PSDwelcome sir.

Do you have a preference on wiring harnesses? I drive a 2002 Ford F350 super duty with a 7.3. It currently has 447,444 miles on the odometer. I replaced the engine with a pilot motor at around 404,000.

From what I’ve seen you’re one of the most knowledgeable PSD people I’ve come across. I’m at a loss for things to check I have a 2000/7.3 that was removed to repair a broken bolt in the water pump, don’t ask I didn’t uninstall the engine I can’t get the engine to start I did all your checks and no start. New fuel pump & batteries glow plugs ok oil in HPOP IPC IS New disconnected still no start I have no scanner to check HPOP out put. Is it possible the LPOP lost its prime and can I remove the OP sending unit and pump oil in to prime the oil pump. Also the starter seems not to crank as fast as the videos I’ve watched. I’d hate to replace the IPM if it’s not bad. I’m an GM wrench and worked on many GM Diesels I rebuilt many standing injection pumps I’m pretty handy with a wrench and hate to replace parts not needed but I’m at my whits end any suggestions would be appreciated also I disconnected glow plugs and tried WD40 we started GM diesels with WD and tried some either and it doesn’t even fire I’m lost can you advise. To dalebowling4@gmail. com

Bypassed the IPR and truck started but not smoothly, Saw in akother video the same thing started the truck, After the guy replaced the harness it cleared up, would you recommend an aftermarket wire harness that's not as expensive as oem?

U give me hope to get a non running 97 7.3

What about glow plugs? I’m surprised you didn’t cover that early in. I have a 99 7.3 and I am having trouble when it’s 20 Fahrenheit.

Hey Clint, is there anyway for the check ball held under the non serviceable plug to go if it is lost in the pump ?

I can attest that the Hot Shot Stition Eliminator works! I had a miss fire till she, the 7.3 not the wife, warmed up! And been running Power Service in my fuel for 22 years and that works great, fuel bowl is as new! and my 2000 F-250 is running as good or better than new.

@sirseven3

Жыл бұрын

My injectors went out in the winter, prior I did sticking eliminator and it got me all the way to then! Stuff made a big difference until they just couldn't try to fire anymore

Thanks for another great video. I fought through many issues with the hard/no start. The starter just sounded weak. A new starter, powermaster, did the trick. The truck started an ran well. BUT about 2 weeks later; Got in, turned the key, all the lights illuminated, normal, Turned to start and nothing, everything went dark. Any suggestions?

Thanks so much for your 7.3 videos! I’m experiencing a problem with mine that has me baffled. This is a 2002 model f450 with only 5800 miles. Obviously bin sitting much of its life. The problem is when cranking for start hpop doesn’t build for 6 to 8 seconds. According to the scan gauge I have connected. Will the ipr pid today too determine its position through this scenario. This is regardless of ambient or engine temp. It then builds pressure starts and runs normally . The crank rpm seems normal. I checked the oil level in the reserve chamber and it remains full. Would a ipr or hpo sensor cause this problem? They are next on my list but I wanted to check first before throwing additional parts at it. Btw the oil is fresh 15/40. Thanks

My 2001 f350 was running fine my son drove it to work and home he parked it in the driveway and went in the house for about 2 hours went back out to leave and truck hasn't started since. My hpop ipr was still plugged in and wire at plug is good. My tach isn't moving during cranking so I replaced the cam position sensor. Still no start I drive a big truck and had to leave so I still don't know what the deal is. Worst part is it drove home fine and just didn't start again. And I unplugged the icp and it didn't crank.

I have a question for you sir, I am fighting a crank no start with a constant check engine light. At the end of the buzz test the SES light turns off until the key is recycled. What can this be an indication of? I do not have rpm on dash and have verified continuity with cps, and pcm to IDM. New IDM as well

I wanted to get the scanner you listed but was having trouble finding it here is one I found that is wired which is fine for me to my laptop WILL it do all that the model you recommended??? I haven't ever asked a question on KZread.

Selling my 07 getting the ad out their

get Video, my 2002 7.3 won't do the buzz test any more only the tach gauge needle moves but no injector sound.. can you help ty

We need a "much more easier" t-shirt.

Well I gone through many of your videos. Had a 7.3 spose to be a good runner that i swapped out. Started out it didn't have hpop pressure changed IPR and had IPC error so changed it and got 2700 psi. Made sure i had fuel filling my bowl rapidly. Used forscan app to check everything from my fuses, rpms, voltage drop starting, hpop pressure, no codes, ebpv pressure, no injector leaks cranking it. Just got white smoke and didn't sound like it was going to start. Was at what else can I do? I didn't pull the idm. Figure i would try doing compression test and if i did it correctly the engine must be bad. Had a cylinder that was at 150. Most were 200 and a cylinder at 300. So I assume it needs a overhaul. I read pressure should be around 400 psi.

@sirseven3

Жыл бұрын

Did you ever solve?

@kennethmabus381

Жыл бұрын

@@sirseven3 didn't go any further on that engine after it failed Compression test. Assume it needs a overhaul.

👍

learning so much thankyou cannot locate engine harness can you please help me

Hello Clint, I watched your video on no start 7.3L, my truck keeps burning out the fuel pump on the side rail and burning out that 30amp fuse you showed in the video, any suggestions on where to start, Thank You

@CUSTOMWORKS7.3PSD

Жыл бұрын

wires are backwards or a slight ground contact some where in the wire harness, trying a completely different part distributor also, Where you are getting it from could have a complete bad batch run or the clap is to tight I've seen this also

mornin, recently i installed a new hpop on my 2001 f250 7.3 and bew valve cover gaskets,it seems the truck idles a little faster but the main problem is after driving it and shutting of for maybe 2 hrs when i hit the key it spins over like it will start but and after doing this a while it;ll start last nite this happened and i just happened to put my ful pedal down a little and it fired right up. im confused

Clint, my 16 y.o. son has an '01 PSD . It currently starts, runs scrappy for 3 seconds, then dies. Any ideas? We've recently changed oil/filter and fuel filter. Changed the camshaft sensor when this problem popped up.

Replaced the IPR and fuel pump and it still would not stay running. Pulled the plug on ICP and it ran, a little rough but it ran. Replacing the ICP tomorrow.

What are all your reputable aftermarket part sources as mentioned in video ? Thanks!

@CUSTOMWORKS7.3PSD

2 ай бұрын

/www.riffraffdiesel.com has the freshest parts

question, can the forscan app do things like change the tire sizes etc in newer trucks, or activate the integrated brake control module on the newer trucks etc

@CUSTOMWORKS7.3PSD

Жыл бұрын

No but this can and its on sale now don't wait amzn.to/3ObaU5a

Great info like always mr Allen. Mr Allen I have this 97 f250 7.3 that every time idling or running it suddenly dies. But then you can crank it and it turns back on like nothing. I've done a adrenaline hpop all new sensors. And still getting the same problem. Have you ever had an issue like that before. Truck has 350k miles

@coolblue4077

Жыл бұрын

Did u try replacing or check camshaft position sensor

@texasobs_73esquivel94

Жыл бұрын

@@coolblue4077 I did got a new one from the dealership and still do the same thing.

@coolblue4077

Жыл бұрын

Oil full in oil tank going to high pressure oil pump

@texasobs_73esquivel94

Жыл бұрын

@@coolblue4077 yes, I actually put in a new adrenaline hpop thinking that would fix it and still does the same crap. What I'm now thinking that it could be is the valve cover gaskets.

Hello sir first off I really appreciate the knowledge u have and it's really beneficial for us. Now my question is I took the fuel bowl off and replaced the orings on it and put it back on plus I did replaced the ebp sensor the braket that holds it and cleaned the tube put everything back and now my truck cranks no start. I did checked the fuel bowl the fuel is coming inside the bowl I did unplugged the icp to check if that's the problem it still doesn't start. If anything u could help me plzzzz. Thanks alot

@CUSTOMWORKS7.3PSD

Жыл бұрын

Year? So some idea's fuel bowl spring issue not building 50 psi, fuel line grommets covering or sucking air, fuel bowl heater broke or not connected or fuse blown, bad wire or connector, Ipr connection disturbed or wire broke or bad connector, It would run with anything wrong with the ebp sensor unless wire was shorted, long shot here but pulled the cam sensor wire loose. ecm fuse blown do to long cranking before fuel made it to injectors weird but have had this happen /// Try these has to be one of the above with the info you provided

@bxtbill

Жыл бұрын

@@CUSTOMWORKS7.3PSD its 2002 f550

@bxtbill

Жыл бұрын

@@CUSTOMWORKS7.3PSD I checked all the fuses they are good so I think maybe what u was saying the cps wire thing is it somewhere close to the ebp tube or in that way?

what engine wiring harness do u suggest

Would a bad coolant sensor cause a no start? I did a new LPOP and fluidampr, flushed the coolant. Put it all back together and it started then died after 5-10 seconds.

@CUSTOMWORKS7.3PSD

Жыл бұрын

no that sensor wouldnt cause this /// gixxer4eva gixxer4eva Publicly subscribed to you (3 weeks) • 7 minutes ago I changed my LPOP because it was leaking. I went to start the truck back up and it died. I filled up the hpop reservoir and again it died. Is there a correct priming procedure for this LPOP job? 7.3 POWERSTROKE EMPTY HPOP RESERVE TANK FIX................. Custom Works Custom Works • 1 second ago The pump gear needs to be in the correct direction The gears are marked then you need to slather the gears with Lubriplate Motor Assembly Grease Motor Assembly Grease so it can gain suction