Пікірлер

• 
  @udx-483muddbucket517 күн бұрын

  Great contact Peter. It would have only been better if it were me you were talking to. lol ✌✌

• 
  @lucdemey328517 күн бұрын

  Fantastic done have also a ic718 Luc 16IR101 16RC555

• 
  @29fb04017 күн бұрын

  @@lucdemey3285 thank you I think is is my favourite hf radio.... Simple to use great big numbers no frills radio

• 
  @lucdemey328517 күн бұрын

  @@29fb040 yes i know how is the connection with the acom 1010 is thiss easy how much power you put in to drive it???

• 
  @29fb04017 күн бұрын

  @@lucdemey3285 connection is good through the correct IC-718 lead Drive in is 60 watts and for that I get a voice peak of 500-600 pep on ssb..... with a constant generated sine tone I get the full 800 on sbb shop.technofix.uk/13-pin-linear-amp-switching-cable-for-icom-ic-703-ic-706-ic-718-ic-7000-ic-7100-ic-7300-ic-7410

• 
  @MANNNDE226 күн бұрын

  43wr677 Tasmania.

• 
  @MANNNDE226 күн бұрын

  43wr677 Tasmania.

• 
  @29fb04026 күн бұрын

  Lol sorry typo on small phone keypad 😳

• 
  @19EE050Ай бұрын

  Nice video

• 
  @13-EK-991Ай бұрын

  Tony is shaking the trees in ireland😂💪👍Echo Kilo Power❤

• 
  @29fb040Ай бұрын

  Yes he asked for eqsl. But when I went on cluster. Dx he has his account set to only through eqsl manager to score ek club points I expect so unfortunately for Mr tony no eqsl card from me But strange conditions hearing the carabian at 9:00am London. Dublin. Lisbon... time

• 
  @lucdemey3285Ай бұрын

  I also have a icom ic718 and a ic706mk2g Luc 16IR101

• 
  @andik859Ай бұрын

  You need a president washington. 😂 Is the kl505 no hd amp ? Most people buy for export radios the hd amp for 35 Watt input.

• 
  @29fb040Ай бұрын

  I have the KL-505v it's is the ham radio vision of the KL-505 it takes 10 watts imput and gives around 240 pep out..... It has much wider band usage than the cb vision the kl-505 which takes a higher imput and gives 300 out but it's not as clean modulation.... The cb radios are only on an 827 vertical antenna and just toys.... For serious dx I use hf radio an lfa beam and the acom 1010

• 
  @29fb040Ай бұрын

  I don't need a Washington (common name the president washing machine) i'm very happy with my two lincoln radios 🤣🤣🤣😢

• 
  @andik859Ай бұрын

  @@29fb040 i know the old lincoln radios. My cb time is over 30 years ago, but the old man have that lincolns in my youth time. I have a old Sirtel S 2000 5/8 Base Antenna polished up and rebuild my station next time. Looking for a good AM FM SSB radio. I think a good catch is the new Anytone 6666 pro. Washington is very expensive. Lincoln 2 + is a good radio too.

• 
  @helsing69Ай бұрын

  thx for the contakt and the video 13 lr 020 olaf

• 
  @29fb040Ай бұрын

  I spell your name incorrectly sorry... As you can hear Italy was making it difficult for good qso

• 
  @outsidefotomons719Ай бұрын

  Hello I'm 16ID64 thanks for the video i put on my FB 73/88 📡🎙️

• 
  @29fb040Ай бұрын

  That's OK. 73's good dx 👍

• 
  @19EE050Ай бұрын

  kzread.info/dash/bejne/eYd3xtCnn8jQmJM.htmlsi=x3Ys4rNm4QgoIICn

• 
  @PaulVerlindeАй бұрын

  Hello peter, good job buddy all the best my friend from paul🇧🇪belguim🇧🇪73's and good dx'ing from 16. Sd .114 paul 👌👍👏👏👏✌😊👍

• 
  @udx-483muddbucket5Ай бұрын

  Yes that is a great capture. I spoke with her once under the Needle Bender call. Hopefully we can get conditions again soon. ✌✌

• 
  @outsidefotomons719Ай бұрын

  Im 16ID64/NB64 Isabelle 📡🎙️ Whats your callsign?

• 
  @bobdillashaw4360Ай бұрын

  Beautiful Cobra 2000

• 
  @29fb040Ай бұрын

  Thank you 😁 it's just a vinyl wrap from. Amazon.... But it turned out good I'm still looking out for a matching speaker even the case from one would do and I could just fix one or both of my little speakers inside it but the speakers are more expensive than the radio was..

• 
  @andik859Ай бұрын

  This echo is too much. Horrible. 😮

• 
  @29fb040Ай бұрын

  In your opinion..... Some people like echo some don't personally I don't care either way I speak with anyone with echos or no echos.... Skip the people with echos or go watch some other videos 😊😅

• 
  @udx-483muddbucket5Ай бұрын

  I could handle a little short skip like that. Beautiful lay out.✌✌

• 
  @andrewverran3498Ай бұрын

  Hi, if you want to mount the PLJ6 into a hobby box with 2 so239 in/out, do you know what value resistor that bleeds off the bar joining the SO239s centre pins ? 73.😊

• 
  @udx-483muddbucket5Ай бұрын

  Nice capture. ✌✌

• 
  @udx-483muddbucket5Ай бұрын

  Beautiful fish and environment. You've done a great job creating it. ✌✌

• 
  @stoatrepublicАй бұрын

  That sounds like Dave from Scatby in Norfolk.

• 
  @19EE050Ай бұрын

  thnx for the video friend 19LR050

• 
  @electrocarbidАй бұрын

  What kind of cool VU Meter is this? Looks so cool!

• 
  @29fb040Ай бұрын

  It's just a cheap light bar from amazon they are just sound activated plugs in to a USB port for power and you can change the colour and rhythm of the lights they only cost a few quid on amazon I think it was around 10 UK 🇬🇧 pounds about 12 euro

• 
  @29fb040Ай бұрын

  This is the ones I bought two for £18 UK pounds.... www.amazon.co.uk/Auraglow-Sound-Activated-LED-Light/dp/B0BDZM1WQV/ref=mp_s_a_1_3?crid=2TOY5VWZN2XR4&dib=eyJ2IjoiMSJ9.wA2SqzA34VjjHO4WBQxK0j7p98AuoOVj3E5oCEYtNzC8sLAZQ3wjLf7cGWMg0j1vF9A1DmGDlHh6x05ymOp021r2Hxs5bvuGFlksHS6VIPQsOMdSOX3rIo01dFDAmnKVdKz_WnBW8rlLQdZfj93sJrG6NaKif-p1Ys-YT8zRtEJVtGXRpjf-BQL01jtiuMZ3T4nz7USxcdKICISxeeYqKQ.HeQvgkGpRSQcyNczTAYciout_LAc61UTIMoxnYiZpfA&dib_tag=se&keywords=sound+activated+light+bar&qid=1718732745&sprefix=Sound+activated+light%2Caps%2C141&sr=8-3

• 
  @andykerr3803Ай бұрын

  Beautiful and good sound 👍

• 
  @ericnixon4225Ай бұрын

  Awesome video of this 10 meter transceiver.i had a President HR2510,which in my opinion there is not much of a difference in the two pieces of equipment other than the nameplate.beautiful radio regardless. Peace and Forever Blessings...73s and KEEP ON BROADCASTING IN THE GREAT WORLD OF RADIO COMMUNICATIONS!✝️🙏❤️🌎🇺🇸👍😎

• 
  @29fb040Ай бұрын

  Thank you

• 
  @MrJarbuckАй бұрын

  big difference in the audio for deffs.

• 
  @29fb040Ай бұрын

  Look at the s meter on my radio your signal jumps up nearly 2 s points when you turn the processor off 😱 audio way better too

• 
  @davetherave4328Ай бұрын

  i want one

• 
  @29fb040Ай бұрын

  What country are you in

• 
  @davetherave4328Ай бұрын

  England,midlands based

• 
  @davetherave4328Ай бұрын

  England,midlands based

• 
  @29fb040Ай бұрын

  OK comment with your email once I email you you can delete the comment again.... 👍👌Or better still I will delete the comment with your email. On it soon as I see it appear

• 
  @chasie5928Ай бұрын

  im running a HD CV40 carb 175 main 48 pilot and its running amazing, just recently took it on a 3 hour trip to carlsbad cavern and back and it ran amazing with 0 issue.

• 
  @29fb040Ай бұрын

  Good for you nice one but why you telling me this

• 
  @upurkilt72468 күн бұрын

  Are you running the cv40 on a 535 virago?

• 
  @29fb0408 күн бұрын

  @@upurkilt7246 no

• 
  @ramonbennett8416Ай бұрын

  I have been trying to email you but it’s coming back email not found.

• 
  @29fb040Ай бұрын

  Yeah as it says comment with your email and I will email you

• 
  @29fb040Ай бұрын

  Still don't see you email in comments

• 
  @KATECERadioDXАй бұрын

  Good morning Peter, great to catch you again, sounding awesome coming into the old school Washington..💥

• 
  @GeorgeZ213Ай бұрын

  Not sure about EU, but cb radio in USA is 11 meter (27Mhz) not 15 Mhz

• 
  @29fb040Ай бұрын

  Lol 😂 you need glasses I'm using it on 27mhz

• 
  @RideGasGasАй бұрын

  I think the one counter was sensing an ambient ~15 MHz signal when the CB transmissions weren't present. When the transmitter was keyed the counter sensed 27 MHz, then went back to ~15 MHz when the transmitter was unkeyed.

• 
  @29fb040Ай бұрын

  Exactly lol

• 
  @jeffwright6685Ай бұрын

  The radio is generating a mixing frequency that the frequency counter picks up when you key the radio at 27mhz has more wattage so the frequency counter picks it up.

• 
  @29fb040Ай бұрын

  @@jeffwright6685 any rf sencing frequency counter does that all these people spending 100's on these ghost hunting devices on ebay are just buying a fancy box that does the very same thing with an rf sencing oscillator hooked up to a light bar.... That sences ambiant rf fields and they think it's a ghost 🤣🤣🤣🤣

• 
  @franciscobenedito34802 ай бұрын

  Bela moto linda máquina gostei passeiro tamo junto gostei da moto linda máquina gostei passeiro tamo junto valeu

• 
  @29fb0402 ай бұрын

  English please 😁

• 
  @MM0IMC2 ай бұрын

  Port isolation problems on the amp or a faulty antenna switch relay in the amp? 🤔

• 
  @29fb0402 ай бұрын

  I bought a new main board the one with the two relays on it and stuck it in seemed to sort it out..... The board is expensive enough 165 euro plus postage direct from acom.... I then bought the two relays from Farnell.... About 12-15 euros each..... But i haven't gotten round to changing them out on the old board yet.....

• 
  @drowningbanana38903 ай бұрын

  Hey man, thanks for sharing - undertaking a single carb conversion for my 535 with the same carb, just wondering what jets you used as a baseline for my own. Cheers!

• 
  @29fb0403 ай бұрын

  OK if using the same tm34 carb you need to adjust the float height before jetting as it will leak fuel. Out the overflow when on the side stand and possibly on cornering too although I can't comfirm. If it does it cornering but it does do it on the side stand.... If you don't and do it later then you have to re jet as lowering the fuel level. In the carb leans out the engine again..... My jetting was pilot jet was in previous comments.... 155 main needle clip in top groove so needle as low as it goes.... The pilot jet I tell you in next comment as I can't remember..... Off top of my head if I settled on 15.0 or 17.5

• 
  @29fb0403 ай бұрын

  Yes 17.5 pilot jet and I thing mixture screw ended up at one full turn out.... My bike had the black widow replacement pipes and headers on it that may or may not make a difference Did you watch the other two videos of it idling and my 15 mile run?????

• 
  @drowningbanana38902 ай бұрын

  @@29fb040 Thanks for all the advice pal, that's really helpful! I'll check out your other stuff on your bike when I finally get round to ordering new jets for this carb

• 
  @29fb0402 ай бұрын

  @@drowningbanana3890 no bother buddy goodluck

• 
  @lsvturbo20333 ай бұрын

  I’m just getting into cb radio and would like to learn more. I’m a dad of 4 boys and I think having a cb or hm radio is important to have and learn how’s to use just in case of an emergency. Cool 😎 video from and hi 👋 from the u.s.a

• 
  @29fb0403 ай бұрын

  A ham radio that is wide banded to cover cb radio frequency is much better than a cb radio in my opinion

• 
  @lsvturbo20333 ай бұрын

  @@29fb040thanks, I’ll look into it

• 
  @29fb0403 ай бұрын

  @@lsvturbo2033 also when the solar cycle ends. Cb radio skip conditions will cease and you still have option to complete an amature radio license as other bands will remain open.... Without buying more equipment... Like any hobby its easy to get carried away and end up with lots of stuff just for the sake of having it a reasonable hf radio second hand shouldn't cost much more than a good cb radio bye

• 
  @scarygary-qq1pj3 ай бұрын

  👀 👃 👄

• 
  @davidmaxim69724 ай бұрын

  Great QSO my Friend VE7WWY 2:12

• 
  @simplelife68274 ай бұрын

  Great tanks you have there. No idea why people make keeeping Goldfish look so hard. Liked and subbed.

• 
  @29fb0404 ай бұрын

  It's easy enough if you follow some simple rules..... Weekly 30% water changes after cycle is Finnished whether or not ammonia or nitrite is present or not.... No substrate or very deep substrate of a fine gravel 1-2 mm diameter no in between.... Deep or none.... and at least double the filtration you think you need....

• 
  @simplelife68274 ай бұрын

  @@29fb040 Why do you say deep or none?

• 
  @29fb0404 ай бұрын

  A deep substrate allows fine dirt to filter down through it locking it away as a mulm if the substrate is not deep enough or fine enough that dirt and mulm and it's toxins get churned up over and over again as the goldfish forage in the substrate a finer gravel also does not allow food to get lost in it causing excess waste....... Other way is a no gravel bare bottom tank in which you can syphon all the waste and dirt out regularly and you can see its gone.... Coarse gravels no matter how deep should be avoided they allow food waste in between the gravels it's then lost and they are. Not able to lock away mulm or it's associated toxins.... What's on the bottom of the tank is as important as the rest of the tank.....

• 
  @whataboutrob4424 ай бұрын

  Subscribed to your channel. I absolutely love goldfish.

• 
  @29fb0404 ай бұрын

  Me too but you need a few to make a good sandwich 🥪 😋

• 
  @whataboutrob4424 ай бұрын

  @29fb040 Plus, it's Good Friday!

• 
  @solarforfuture4 ай бұрын

  solar flare skipper

• 
  @mikemarch54804 ай бұрын

  Grants pass! Just down the road from me, I'm in Coos Bay!!

• 
  @29fb0404 ай бұрын

  Nice if your on the radio I might catch you before the cycle ends although it's hanging in I would expect USA and Canada to fade out in the summer but who knows it's been a strange cycle this time

• 
  @toriechuntraruk36114 ай бұрын

  Thank you for the info

• 
  @29fb0404 ай бұрын

  No bother have you or are you setting up a small tank

• 
  @toriechuntraruk36114 ай бұрын

  Will set up a 30 gallon tank

• 
  @29fb0404 ай бұрын

  @@toriechuntraruk3611 nice good luck there are some videos on water and fish in cycling etc further down with lots of info in discriptions etc you might find useful or you might not either way good luck.... Best tip is but double the filtration you think you need if you think you need one fluval 3 buy two lol I'm not a big fan of external filters for goldfish most are gravity fed into the filter and that don't create enough suction to move the bigger bits of goldfish poop into the filter.... Anyway goodluck hope it works out if you want a video on anything specific I'll try to do it if it helps out

• 
  @toriechuntraruk36114 ай бұрын

  Beautiful goldfish. What is your substrate?

• 
  @29fb0404 ай бұрын

  Thanks the substrate is a mixture of normal pea gravel and this stuff I get it in pets at home it's called aquarium sand but it's alot bigger than sand it's about 2mm it's mixed about 50/50 not on purpose it's just a mix of stuff I had in a big tub in the shed when I set the tank up from a mixture of small tropical tanks and shrimp tanks I had dismantled over the years..... www.petsathome.com/shop/en/pets/pets-at-home-aquarium-sand-black-8kg

• 
  @kilcar4 ай бұрын

  Donegal! where my grandparents hailed from! Towney, Kilcar, To be precise. Im working on my HAM license now, hope to DX with you from Bend, Oregon. Slan!

• 
  @29fb0404 ай бұрын

  Yeah it's a good bit away from me but I have friends in kilcar and Carrick..... Also teelin..... Its roughly 90miles away there's a big station Michael out that way about halfway between killybegs and kilcar can't remember his callsign though....

• 
  @29fb0404 ай бұрын

  I was happy to get oregon last week I set myself a personal challenge to log all the states of America and the provinces of Canada 😀 before the cycle ends started at Christmas so far I have 39 states and five Canadian provinces.... Anyway I do have a ham call too but I seldem use it I much prefer cb radio good luck

• 
  @29fb0404 ай бұрын

  Link to oregon qso kzread.info/dash/bejne/q36lybWsfMjQhLg.htmlfeature=shared

• 
  @Teabone34 ай бұрын

  nice

• 
  @29fb0404 ай бұрын

  I will do snother update in September that will be a year from i set it up ..... As theres nothing more to add to this series ...... Any questions post in the comments 😊

• 
  @AndrewSparkfish4 ай бұрын

  Now seriously thinking twice about the purchase, yet the comment from Canada says it's all good in the wind.

• 
  @29fb0404 ай бұрын

  Only one way to find out for yourself isn't there 😁

• 
  @29fb0404 ай бұрын

  The Canada guy also says remember to use the locknut next time..... As you will see I asked him what lock nuts? As there are no lock nuts on a sirio 827 so I would take with a pinch of salt what Canada guy says but yes you are right there is as many happy with it as there is that had problems

• 
  @AndrewSparkfish4 ай бұрын

  Thinking of getting an 827 ...but seeing this am now a wee bit concerned as the wind can really pump here...

• 
  @29fb0404 ай бұрын

  Sure buy it and see or buy it and do the mods before you put it up..... Anyway sure I contacted sirio and they said it was my fault I didn't construct it professionally 🤣🤣🤣

• 
  @AndrewSparkfish4 ай бұрын

  Thanks for that, @@29fb040

• 
  @29fb0404 ай бұрын

  It's been repaired and up again nearly two months and it's working well and swr stayed the same

• 
  @andik8594 ай бұрын

  Granpa Ervin commando posten. 😂

• 
  @udx-483muddbucket54 ай бұрын

  Awesome station you have there. Great contact. ✌✌

• 
  @29fb0404 ай бұрын

  I'm in a good location and been on a lot of years so I have been building it up for a good few years

• 
  @udx-483muddbucket54 ай бұрын

  Hi Peter, Karl 26 CT 4875 passed the link to this video to me. Thank you for sharing your knowledge with us novices. lol Hopefully I will be able to utilize this information and get started. I hope to catch you on the air again soon. 73 ✌✌

• 
  @29fb0404 ай бұрын

  No problem buddy hope it helps you too

• 
  @29fb0404 ай бұрын

  If you need more help just ask

• 
  @udx-483muddbucket54 ай бұрын

  @@29fb040 I got it figured out, now I just have to make a nice platform. ✌✌

• 
  @29fb0404 ай бұрын

  Nice one buddy

• 
  @29fb0404 ай бұрын

  I might write it all down and redo the video make it shorter and more exact cos there's a lot of me refreshing cos I clicked the wrong thing etc 😂