I have a 1995 36v yamaha , been looking for some info ,I stumbled upon your video ,my setup is not v-gluide but a square gluide . same concept though , thanks for posting this video .
@waynemartin.waynesgolfcart490014 сағат бұрын
Sounds like you have pb8 style potentiometer.
@scotttitensor85572 күн бұрын
Great video. Really appreciate. In the process of replacing the MCOR on my 04. My cart has a brake light issue workaround that has been done, resulting in some different challenges.
@waynemartin.waynesgolfcart4900Күн бұрын
You can text me if you need advice.
@jrobbbins6 күн бұрын
Where can I purchase these parts?
@waynemartin.waynesgolfcart49005 күн бұрын
If you are looking for light kits, I have them on my website. If you only are looking for the brake plunger part, redhawk is the only place that has those.
@jrobbbins5 күн бұрын
@@waynemartin.waynesgolfcart4900 Thank you
@WrenlyMari8 күн бұрын
Thank you so much sir for all of your wonderful tutorial videos. 👌
@nathanberbereia110910 күн бұрын
I have an RXV cart. I upgraded to a bigger controller. I didn’t notice it at first but I’m getting this jerking motion when I slow down. For example slow down to make a turn it jerks like it wants to stop then it will go. Does this sound like it’s the bearing encoder or the controller?? Thanks for any info.
@waynemartin.waynesgolfcart49009 күн бұрын
It could be either of them. Are you sure your bigger controller is compatible with the motor? Also if you didn't upgrade to a larger amp solenoid, that could be the problem.
@noreenbaxter98711 күн бұрын
I have a club car sd 1991 there are no doors under the mat. Please help me with an old golf cart
@waynemartin.waynesgolfcart490011 күн бұрын
You are correct, ds carts never had a door under the mat. How can I help, if you don't give me any information?
@bpneeley1ify12 күн бұрын
Do you have any videos of preparing controller or do you know any are?
@waynemartin.waynesgolfcart490011 күн бұрын
There is no repairing of controllers, you need to have it rebuilt.
@Rixer-ng3mm12 күн бұрын
Hi Wayne. Just found your video. Thank you for the help. My cart has 40010815803 stamped into it. Can you tell me what year it is?
@seancasey623312 күн бұрын
Leak of brake fluid on an electric club car...how to diagnose and repair
@waynemartin.waynesgolfcart490011 күн бұрын
Not many electric carts have brake fluid. If you park the cart in a clean area and pump the brakes a few times, you should see about where the leak is by the spots on the floor. Should be fairly easy to locate the leak, unless you have a tomberlin, then you have a big headache.
@kevinimerti752214 күн бұрын
Hey Wayne how much is The Royale kit for my 2010 president Club Car 50 amp hour
@waynemartin.waynesgolfcart490013 күн бұрын
I'm not sure what you are asking ? If you are asking about batteries, you need to find out from someone in your area, all areas are not the same.
@jeandupoux417916 күн бұрын
Wayne thanks a million !! You helped me alot. It's great how you explained everything !! Straight forward....Happy 4th of July 2024
@waynemartin.waynesgolfcart490015 күн бұрын
Thank you sir !
@darwinhippen701018 күн бұрын
Thank you so much for these videos appreciated.
@waynemartin.waynesgolfcart490017 күн бұрын
👍
@John-NeverStopLearning20 күн бұрын
Hi Wayne, you mentioned there was a code from the golf cart, how and what did you use to get the code?
@waynemartin.waynesgolfcart490019 күн бұрын
Each club car controller has 4 codes programmed into it from the factory. With a scanner, the first 3 codes can be unlocked for free. You have to pay club car to get the unlock code for code 4.
@marclissoway263820 күн бұрын
Hi I enjoy your info. I have a club cart precedent, the other day it stopped running just completely dead. I replaced my motor computer, that made it run again however now it has low speed. Maybe 4 MPH before it was at least double that. I replace the speed sensor that did not increase the speed?? When I first got this cart it was used and a mechanic from the place where I bought it plugged a hand held looking mini computer and it boasted the speed to at least 12 mph. Would I need that done again? So far I’m stumped.
@waynemartin.waynesgolfcart490019 күн бұрын
Yes it is possible for a controller to loose its memory ( settings ). With a scanner you should be able to get to about 17 mph without paying for a club car code.
@marclissoway263820 күн бұрын
I have replaced my Controler, as my cart just stopped that has made it run again , but my speed is very slow like 5 or 6 mph, I have installed a new speed sensor, it hardly made any difference. Any Ideas?
@waynemartin.waynesgolfcart490020 күн бұрын
Your new controller may only be set for code 1 speed, or maybe your magnet is cracked or bad?
@j.delgado436120 күн бұрын
I need help. After changing out my batteries, my taillights work, but my front led light doesn't anymore. What could be wrong? I checked one fuse and it's fine. Did my led light burn/short circuit perhaps?
@waynemartin.waynesgolfcart490020 күн бұрын
It could be lots of things, bad switch, bad bulbs, wire came loose, wire not hooked up, etc. It should be an easy fix and easy find. See if there is voltage in and thru the switch, check the bulbs for continuity.
@HollyTheBikerChick22 күн бұрын
Thanks you solved a few of my problem ..... It's great that you take time to show people
@waynemartin.waynesgolfcart490021 күн бұрын
Nice, Thank you.
@user-jt9yz9ti7e24 күн бұрын
Thank you Dave for your time and education on the working of the battery chargers.
@waynemartin.waynesgolfcart490023 күн бұрын
Thank you sir, for saying that !
@881167c229 күн бұрын
Hello, from what I see, you have the same car that was given to me to restore. It happens that I have obtained the technical manual, but there are things that I cannot fully understand. The switch that is on the forward and reverse lever looks like a monkey, it is one that when you press the lever, it is activated; It is one that goes inside and is mounted with screws on the lever. You could make a video explaining the electrical wiring. Greetings and I hope you can.
@waynemartin.waynesgolfcart490028 күн бұрын
👌
@markyapong860929 күн бұрын
Verry nicely
@waynemartin.waynesgolfcart490028 күн бұрын
👍
@davidgonzales3265Ай бұрын
Thank you
@waynemartin.waynesgolfcart4900Ай бұрын
👍
@charlesdearing9709Ай бұрын
Hello Wayne, I'm new to the electric golf carts. My relay is not clicking when i plug my cart in & i have 44.5 volts ? I did test my plug on the cart & it's got 44.5. Also if a solenoid sticks can you tap on it to get it to unstick. I ask this because I'm getting 44.5 volts on both large terminals with the key turned off. Thanks Charles
@waynemartin.waynesgolfcart4900Ай бұрын
Your batteries are too low to engage your charger. Try using a 12 volt car charger on each individual battery fir about 15 minutes, then try your cart charger immediately after that to see if the relay will close. Yes you can tap on a solenoid, but that isn't your problem. Also, if you have a resistor that goes between the 2 large solenoid terminals, then you will always have volts on both sides. You need to temporarily remove that resistor to see if you have volts on both sides.
@charlesdearing9709Ай бұрын
@@waynemartin.waynesgolfcart4900 Thank you sir i tried it again and after about a minute it clicked and came on & worked. Can you tell me how to check the solenoid? I'm not getting a click when i turn the key on and the cart will not go in either direction
@patrickfrank366Ай бұрын
How do I know if I have a DS or president? And Why don’t I just replace the obc?
@waynemartin.waynesgolfcart4900Ай бұрын
You can certainly replace the obc, no worries there. A precedent has a rounded front cowl A ds is kind of boxed looking front end.,
@mikecurley7746Ай бұрын
Hi Wayne my name is Mike I have a 2013 48 volt club car is there a fuse that goes to the obc ? My cart stopped working the batteries are at 48 volts the charger works I changed the batteries but the cart don’t work
@waynemartin.waynesgolfcart4900Ай бұрын
No fuse to the obc, but there is 1 fuse I'm line to the solenoid.
@mikecurley7746Ай бұрын
@@waynemartin.waynesgolfcart4900 ok Thanks I will check the Fuse over the weekend ! Will let you know if it fixes it ! Thanks Again mike
@waynemartin.waynesgolfcart4900Ай бұрын
I answered you in the email.
@geraldbrewer7900Ай бұрын
Get to the point
@waynemartin.waynesgolfcart4900Ай бұрын
I see your point, and i like the way you comb your hair around it.
@thom1879Ай бұрын
so, on a newer club car ds or precedent, if you are using an onboard charger and not using the stock charge receptacle anymore, you really just need to splice the white and blue together, then, right? Then the obc can just be removed?
@waynemartin.waynesgolfcart4900Ай бұрын
Yes, correct. However on newer than 2016, they no longer installed obc 's.
@881167c2Ай бұрын
Hello, great video. I wanted to know if you have any explanation of the electrical system of a Club Car Golf with 36 volt batteries and a model 5BC48JB764 engine. Among other questions I have, there is a switch on the forward and reverse lever that does not appear on the electrical diagram sent to me by the manufacturer and I want to know what it is used for. This is connected to the solenoid in its negative position.
@waynemartin.waynesgolfcart4900Ай бұрын
Send me a email or text, telling me the year of the cart, the voltage, and if it has a vglide, pot box etc, and i can send you a wiring diagram.
@881167c229 күн бұрын
@@waynemartin.waynesgolfcart4900 ok, thanks. What is your email?
@melroy3568Ай бұрын
Gas mcor
@GAQ0709Ай бұрын
Friend your the greatest. You helped me solve the first part installation . The foot rest had a couple of pc. Left over parts I guess they are trash. These instructions are terrible. Thank you😅
@waynemartin.waynesgolfcart4900Ай бұрын
Very cool
@RedBirdHobbiesАй бұрын
Can someone recommend me a motor upgrade for a 2003 club car ds? 36 volts
@waynemartin.waynesgolfcart4900Ай бұрын
Plumquick motors
@philiphapeshis1226Ай бұрын
I have an issue with speeed staying in high gear.I can slam pedal down and it goes well then slows down to Medium speed.
@waynemartin.waynesgolfcart4900Ай бұрын
You didn't say if you have a vglide or not. If you do , open it and see if it needs adjustment or if the pads are worn or burnt.
@gtphonesАй бұрын
Hi Wayne, I need your help, money is tight so i am trying my best to do this myself. I have a 99 clubcar ds and i am switching over to lithium. I am trying to bypass my obc bypass. I have the 3 wire set up. Brown, yellow, and red. I found the tubing removed the neagative 10awg and small grey wire from the charger recepticle. I took the 10 ground and placed it on my - battery terminal. I took the yellow wire from the contoller connection and wired it to the negative terminal on my controller along with the 10awg ground wire. I get the reverse buzzer when i turn on the key, but the cart will not move at all. I get the click from the solenoid but no movement. I tried to charge my 4 12v 100ah lithium batteries last night but they did not charge. I have a brand new smart charger and i hooked up the clips it came with. No luck!!!
@waynemartin.waynesgolfcart4900Ай бұрын
As far as the bypass, it sounds like you didn't do it right. The black # 10 wire needs to run from the carts charge receptacle to the main negative on the batteries. The only yellow wire you need to do anything with, is if you have a skinny yellow wire on the solenoid. If you do have this Wire , that wire needs to run from the solenoid to the that same main negative battery terminal.
@gtphonesАй бұрын
@@waynemartin.waynesgolfcart4900 I corrected the wiring on the bypass as instructed. I do have the yellow also on the negative battery terminal from the soleniod. I do have 110 at the controller from the solenoid, but no movement on the cart. Next i will check the switch, but im sure its good. Any ideas what i should check on? Not sure if my controller is fired or what?
@waynemartin.waynesgolfcart4900Ай бұрын
@gtphones I have never heard of 110 volts at a controller, that would absolutely fry the controller.
@gardner-GOLDWINGАй бұрын
Wayne I have question for you . I have 2008 club cart its a 48 v ele the batteries are up good when I accelerate the cart when a slight incline will shut off I move the Excelerator and it starts again and then it goes for a while and does the same thing again which will shut off and then when I move my Excelerator it takes it continues just any idea what I might be looking for appreciate it thanks
@waynemartin.waynesgolfcart4900Ай бұрын
Sounds like maybe a dead spot at the full Throttle end of the mcor.
@gardner-GOLDWINGАй бұрын
@@waynemartin.waynesgolfcart4900 Thanks Wayne I will start there I appreciate the help
@garyrogers906Ай бұрын
My club car is road ready. I could run 25 mph but now I can only get it up to 13/15 mph. It’s not the 8 mph like you said but could it be my speed sensor
@waynemartin.waynesgolfcart4900Ай бұрын
Yes it can be, or even if you had speed code 4 , that could have gone away.
@PCRRAMRODАй бұрын
So I have an old G2 I believe, with a charger that just has a timer on it (up to 12 hrs) recently just purchased this, it was running great and then it wasn't, and acted line it had a short in the wiring when it started to act up and not go, when you hit the gas pedal the led light turned on in front, which made me think it is a short in the wiring, I tried charging the batteries with my charger, 2 at a time, since they are in series, seems like the 2 middle batteries are faulty, they both seem dead, unplugged them to charge individuality, and using a reconditioner currently to try and bring the life back, any advice would be greatly appreciated! Thanks
@waynemartin.waynesgolfcart4900Ай бұрын
I do not believe on any battery reconditioning methods. I would replace all the batteries.
@Jb-co9jmАй бұрын
Shift all the leads down one
@Soccercoach2015Ай бұрын
Hey! You can re upload your video with different titles. I have been searching for 2 years why does my club car start and stop, what does it work then not, not until a video August 2023 that was uploaded that had the title by what people are searching, then i learned it was the mcor and found your video after searching mcor Replacement
@waynemartin.waynesgolfcart4900Ай бұрын
Thanks for the idea, maybe I should go back and do that to some of my videos. 👍
@user-nz8mh3ye9jАй бұрын
thanks Wayne just I have a Club car and the power drive 2 wasn't charging the batteries, I then charge ea battery separate and according to the 12 volt charger i was using the batteries are charged at 60% now i just plug in the power drive 2 to charge and its working currently @ 9 Dc amps how long do i charge it for ??
@waynemartin.waynesgolfcart4900Ай бұрын
It may take 16 hours
@DavidMartinez-uz2vfАй бұрын
Good afternoon.. Do you have and email address
@GregoryRuss-re1vwАй бұрын
Hi Wayne, Just wondering if you would have any video on a XRT800 Club car? I have a 2007 model that mite need an MCOR or possibly a speed sensor. Will an RTS redhot work for this model? Do you sell other club car parts? Thank you
@waynemartin.waynesgolfcart4900Ай бұрын
I sell parts for electric club cars. No videos on that cart, sorry.
@hldmplayrАй бұрын
This worked great! Thanks so much. I never would have thought of this 🎉
@waynemartin.waynesgolfcart4900Ай бұрын
Nice
@droppdon20s1Ай бұрын
I have a 2005 club car precedent gas powered, is there anywhere I can buy an entire pedal assembly for it?
@waynemartin.waynesgolfcart4900Ай бұрын
I do not work on gas carts, however Nivel has almost any part you need.
@bigredjohnson6921Ай бұрын
Great video, but not a good idea using impact on the nut, if you overtighten you can pinch the bearing and after it is pinched it will fail, even if you back it off a little, damage is already done.
@waynemartin.waynesgolfcart4900Ай бұрын
Thank you.
@KaylaSpires-qy3qhАй бұрын
At what point do you unplug it or is it safe to keep it plugged in until you drive again? Will it hurt the batteries to charge after each use or wait until they are drained first?
@KaylaSpires-qy3qhАй бұрын
At what point do you unplug it or is it safe to keep it plugged in until you drive again? Will it hurt the batteries to charge after each use or wait until they are drained first?
@waynemartin.waynesgolfcart4900Ай бұрын
If you have a power drive charger, you can leave it plugged in the cart. You should charger the batteries, at the end of any day that you use the cart, DO NOT wait until it is discharged! Never let the batteries get below 50 %.
@janicescolesАй бұрын
How can I know if the charger has turned itself off?
@waynemartin.waynesgolfcart4900Ай бұрын
The needle will drop to zero, it also will stop humming or buzzing, and it will cool down.
@SpicyBloodBeanАй бұрын
the charger doesn't care what the voltage is! The computer on the cart uses the third sense pin to activate the charger. thats why if the voltage is too low the charger will not come on because the computer in the cart cant tell the charger to come on.. I have been a fleet mechanic at golf courses for fifteen years
@garytube1050Ай бұрын
Wayne, My Crown batteries were 4 years old so I thought my problem was with them. Replaced on the precendent Trojans. It is a 48 volt cart. I charged the batteries up to fool charge. Hit the reverse switch and push the pedal. The voltage display drops to 0%, no light at all. Cart does not move. Any ideas what might be the problem. I put a new speed sensor and a chinese mcor about a month ago before I replaced the batteries.
@waynemartin.waynesgolfcart4900Ай бұрын
Sounds like either you missed a wire or even maybe the tow switch is still in tow?
@garytube1050Ай бұрын
@waynemartin.waynesgolfcart4900 I was wondering if the switch is not working. I am able to push the cart foward and backwards with ease when it is in run.
@garytube1050Ай бұрын
Also if I play with the switch back and forth through run and tow the light indicating full charge flickers on on off.
@waynemartin.waynesgolfcart4900Ай бұрын
Yes, you can push the cart in both tow and run . Will reverse buzzer work in run but not in tow?
@garytube1050Ай бұрын
@waynemartin.waynesgolfcart4900 yes it does buzz when hitting the reverse side. However it buzzes, the voltage indicator drops where it is not visible. Of the cart. After a while it will go through the same sequences.
@janicescoles2 ай бұрын
Wow! Valuable information. Thanks for sharing with us and being so clear.
@waynemartin.waynesgolfcart4900Ай бұрын
Nice.
@Chris-be7wz2 ай бұрын
I have a 2007 precedent , bought new trojan batteries , plugged the cart in and left it for 20 hours or so and came out to the garage with the batteries boiling over and rotten egg smell
@waynemartin.waynesgolfcart49002 ай бұрын
Egg smell is not uncommon. However if charger ran for more than 16 hours, that's a problem. Either the obc is bad, the charger has been bypassed, or you have the wrong charger.
@Chris-be7wzАй бұрын
Must be OBC ,,I have had the cart for 10 years and the same charger the whole time and never had an issue. Thank you for the quick reply! 🤠
@Chris-be7wzАй бұрын
Is there a way to test the OBC?I am proficient with a muti-meter
@waynemartin.waynesgolfcart4900Ай бұрын
Easiest way is to try your charger on someone else's cart and try someone else's charger on your cart. That will tell you whether the problem is in your charger. Or your cart for sure before you replace anything..
Пікірлер
I have a 1995 36v yamaha , been looking for some info ,I stumbled upon your video ,my setup is not v-gluide but a square gluide . same concept though , thanks for posting this video .
Sounds like you have pb8 style potentiometer.
Great video. Really appreciate. In the process of replacing the MCOR on my 04. My cart has a brake light issue workaround that has been done, resulting in some different challenges.
You can text me if you need advice.
Where can I purchase these parts?
If you are looking for light kits, I have them on my website. If you only are looking for the brake plunger part, redhawk is the only place that has those.
@@waynemartin.waynesgolfcart4900 Thank you
Thank you so much sir for all of your wonderful tutorial videos. 👌
I have an RXV cart. I upgraded to a bigger controller. I didn’t notice it at first but I’m getting this jerking motion when I slow down. For example slow down to make a turn it jerks like it wants to stop then it will go. Does this sound like it’s the bearing encoder or the controller?? Thanks for any info.
It could be either of them. Are you sure your bigger controller is compatible with the motor? Also if you didn't upgrade to a larger amp solenoid, that could be the problem.
I have a club car sd 1991 there are no doors under the mat. Please help me with an old golf cart
You are correct, ds carts never had a door under the mat. How can I help, if you don't give me any information?
Do you have any videos of preparing controller or do you know any are?
There is no repairing of controllers, you need to have it rebuilt.
Hi Wayne. Just found your video. Thank you for the help. My cart has 40010815803 stamped into it. Can you tell me what year it is?
Leak of brake fluid on an electric club car...how to diagnose and repair
Not many electric carts have brake fluid. If you park the cart in a clean area and pump the brakes a few times, you should see about where the leak is by the spots on the floor. Should be fairly easy to locate the leak, unless you have a tomberlin, then you have a big headache.
Hey Wayne how much is The Royale kit for my 2010 president Club Car 50 amp hour
I'm not sure what you are asking ? If you are asking about batteries, you need to find out from someone in your area, all areas are not the same.
Wayne thanks a million !! You helped me alot. It's great how you explained everything !! Straight forward....Happy 4th of July 2024
Thank you sir !
Thank you so much for these videos appreciated.
👍
Hi Wayne, you mentioned there was a code from the golf cart, how and what did you use to get the code?
Each club car controller has 4 codes programmed into it from the factory. With a scanner, the first 3 codes can be unlocked for free. You have to pay club car to get the unlock code for code 4.
Hi I enjoy your info. I have a club cart precedent, the other day it stopped running just completely dead. I replaced my motor computer, that made it run again however now it has low speed. Maybe 4 MPH before it was at least double that. I replace the speed sensor that did not increase the speed?? When I first got this cart it was used and a mechanic from the place where I bought it plugged a hand held looking mini computer and it boasted the speed to at least 12 mph. Would I need that done again? So far I’m stumped.
Yes it is possible for a controller to loose its memory ( settings ). With a scanner you should be able to get to about 17 mph without paying for a club car code.
I have replaced my Controler, as my cart just stopped that has made it run again , but my speed is very slow like 5 or 6 mph, I have installed a new speed sensor, it hardly made any difference. Any Ideas?
Your new controller may only be set for code 1 speed, or maybe your magnet is cracked or bad?
I need help. After changing out my batteries, my taillights work, but my front led light doesn't anymore. What could be wrong? I checked one fuse and it's fine. Did my led light burn/short circuit perhaps?
It could be lots of things, bad switch, bad bulbs, wire came loose, wire not hooked up, etc. It should be an easy fix and easy find. See if there is voltage in and thru the switch, check the bulbs for continuity.
Thanks you solved a few of my problem ..... It's great that you take time to show people
Nice, Thank you.
Thank you Dave for your time and education on the working of the battery chargers.
Thank you sir, for saying that !
Hello, from what I see, you have the same car that was given to me to restore. It happens that I have obtained the technical manual, but there are things that I cannot fully understand. The switch that is on the forward and reverse lever looks like a monkey, it is one that when you press the lever, it is activated; It is one that goes inside and is mounted with screws on the lever. You could make a video explaining the electrical wiring. Greetings and I hope you can.
👌
Verry nicely
👍
Thank you
👍
Hello Wayne, I'm new to the electric golf carts. My relay is not clicking when i plug my cart in & i have 44.5 volts ? I did test my plug on the cart & it's got 44.5. Also if a solenoid sticks can you tap on it to get it to unstick. I ask this because I'm getting 44.5 volts on both large terminals with the key turned off. Thanks Charles
Your batteries are too low to engage your charger. Try using a 12 volt car charger on each individual battery fir about 15 minutes, then try your cart charger immediately after that to see if the relay will close. Yes you can tap on a solenoid, but that isn't your problem. Also, if you have a resistor that goes between the 2 large solenoid terminals, then you will always have volts on both sides. You need to temporarily remove that resistor to see if you have volts on both sides.
@@waynemartin.waynesgolfcart4900 Thank you sir i tried it again and after about a minute it clicked and came on & worked. Can you tell me how to check the solenoid? I'm not getting a click when i turn the key on and the cart will not go in either direction
How do I know if I have a DS or president? And Why don’t I just replace the obc?
You can certainly replace the obc, no worries there. A precedent has a rounded front cowl A ds is kind of boxed looking front end.,
Hi Wayne my name is Mike I have a 2013 48 volt club car is there a fuse that goes to the obc ? My cart stopped working the batteries are at 48 volts the charger works I changed the batteries but the cart don’t work
No fuse to the obc, but there is 1 fuse I'm line to the solenoid.
@@waynemartin.waynesgolfcart4900 ok Thanks I will check the Fuse over the weekend ! Will let you know if it fixes it ! Thanks Again mike
I answered you in the email.
Get to the point
I see your point, and i like the way you comb your hair around it.
so, on a newer club car ds or precedent, if you are using an onboard charger and not using the stock charge receptacle anymore, you really just need to splice the white and blue together, then, right? Then the obc can just be removed?
Yes, correct. However on newer than 2016, they no longer installed obc 's.
Hello, great video. I wanted to know if you have any explanation of the electrical system of a Club Car Golf with 36 volt batteries and a model 5BC48JB764 engine. Among other questions I have, there is a switch on the forward and reverse lever that does not appear on the electrical diagram sent to me by the manufacturer and I want to know what it is used for. This is connected to the solenoid in its negative position.
Send me a email or text, telling me the year of the cart, the voltage, and if it has a vglide, pot box etc, and i can send you a wiring diagram.
@@waynemartin.waynesgolfcart4900 ok, thanks. What is your email?
Gas mcor
Friend your the greatest. You helped me solve the first part installation . The foot rest had a couple of pc. Left over parts I guess they are trash. These instructions are terrible. Thank you😅
Very cool
Can someone recommend me a motor upgrade for a 2003 club car ds? 36 volts
Plumquick motors
I have an issue with speeed staying in high gear.I can slam pedal down and it goes well then slows down to Medium speed.
You didn't say if you have a vglide or not. If you do , open it and see if it needs adjustment or if the pads are worn or burnt.
Hi Wayne, I need your help, money is tight so i am trying my best to do this myself. I have a 99 clubcar ds and i am switching over to lithium. I am trying to bypass my obc bypass. I have the 3 wire set up. Brown, yellow, and red. I found the tubing removed the neagative 10awg and small grey wire from the charger recepticle. I took the 10 ground and placed it on my - battery terminal. I took the yellow wire from the contoller connection and wired it to the negative terminal on my controller along with the 10awg ground wire. I get the reverse buzzer when i turn on the key, but the cart will not move at all. I get the click from the solenoid but no movement. I tried to charge my 4 12v 100ah lithium batteries last night but they did not charge. I have a brand new smart charger and i hooked up the clips it came with. No luck!!!
As far as the bypass, it sounds like you didn't do it right. The black # 10 wire needs to run from the carts charge receptacle to the main negative on the batteries. The only yellow wire you need to do anything with, is if you have a skinny yellow wire on the solenoid. If you do have this Wire , that wire needs to run from the solenoid to the that same main negative battery terminal.
@@waynemartin.waynesgolfcart4900 I corrected the wiring on the bypass as instructed. I do have the yellow also on the negative battery terminal from the soleniod. I do have 110 at the controller from the solenoid, but no movement on the cart. Next i will check the switch, but im sure its good. Any ideas what i should check on? Not sure if my controller is fired or what?
@gtphones I have never heard of 110 volts at a controller, that would absolutely fry the controller.
Wayne I have question for you . I have 2008 club cart its a 48 v ele the batteries are up good when I accelerate the cart when a slight incline will shut off I move the Excelerator and it starts again and then it goes for a while and does the same thing again which will shut off and then when I move my Excelerator it takes it continues just any idea what I might be looking for appreciate it thanks
Sounds like maybe a dead spot at the full Throttle end of the mcor.
@@waynemartin.waynesgolfcart4900 Thanks Wayne I will start there I appreciate the help
My club car is road ready. I could run 25 mph but now I can only get it up to 13/15 mph. It’s not the 8 mph like you said but could it be my speed sensor
Yes it can be, or even if you had speed code 4 , that could have gone away.
So I have an old G2 I believe, with a charger that just has a timer on it (up to 12 hrs) recently just purchased this, it was running great and then it wasn't, and acted line it had a short in the wiring when it started to act up and not go, when you hit the gas pedal the led light turned on in front, which made me think it is a short in the wiring, I tried charging the batteries with my charger, 2 at a time, since they are in series, seems like the 2 middle batteries are faulty, they both seem dead, unplugged them to charge individuality, and using a reconditioner currently to try and bring the life back, any advice would be greatly appreciated! Thanks
I do not believe on any battery reconditioning methods. I would replace all the batteries.
Shift all the leads down one
Hey! You can re upload your video with different titles. I have been searching for 2 years why does my club car start and stop, what does it work then not, not until a video August 2023 that was uploaded that had the title by what people are searching, then i learned it was the mcor and found your video after searching mcor Replacement
Thanks for the idea, maybe I should go back and do that to some of my videos. 👍
thanks Wayne just I have a Club car and the power drive 2 wasn't charging the batteries, I then charge ea battery separate and according to the 12 volt charger i was using the batteries are charged at 60% now i just plug in the power drive 2 to charge and its working currently @ 9 Dc amps how long do i charge it for ??
It may take 16 hours
Good afternoon.. Do you have and email address
Hi Wayne, Just wondering if you would have any video on a XRT800 Club car? I have a 2007 model that mite need an MCOR or possibly a speed sensor. Will an RTS redhot work for this model? Do you sell other club car parts? Thank you
I sell parts for electric club cars. No videos on that cart, sorry.
This worked great! Thanks so much. I never would have thought of this 🎉
Nice
I have a 2005 club car precedent gas powered, is there anywhere I can buy an entire pedal assembly for it?
I do not work on gas carts, however Nivel has almost any part you need.
Great video, but not a good idea using impact on the nut, if you overtighten you can pinch the bearing and after it is pinched it will fail, even if you back it off a little, damage is already done.
Thank you.
At what point do you unplug it or is it safe to keep it plugged in until you drive again? Will it hurt the batteries to charge after each use or wait until they are drained first?
At what point do you unplug it or is it safe to keep it plugged in until you drive again? Will it hurt the batteries to charge after each use or wait until they are drained first?
If you have a power drive charger, you can leave it plugged in the cart. You should charger the batteries, at the end of any day that you use the cart, DO NOT wait until it is discharged! Never let the batteries get below 50 %.
How can I know if the charger has turned itself off?
The needle will drop to zero, it also will stop humming or buzzing, and it will cool down.
the charger doesn't care what the voltage is! The computer on the cart uses the third sense pin to activate the charger. thats why if the voltage is too low the charger will not come on because the computer in the cart cant tell the charger to come on.. I have been a fleet mechanic at golf courses for fifteen years
Wayne, My Crown batteries were 4 years old so I thought my problem was with them. Replaced on the precendent Trojans. It is a 48 volt cart. I charged the batteries up to fool charge. Hit the reverse switch and push the pedal. The voltage display drops to 0%, no light at all. Cart does not move. Any ideas what might be the problem. I put a new speed sensor and a chinese mcor about a month ago before I replaced the batteries.
Sounds like either you missed a wire or even maybe the tow switch is still in tow?
@waynemartin.waynesgolfcart4900 I was wondering if the switch is not working. I am able to push the cart foward and backwards with ease when it is in run.
Also if I play with the switch back and forth through run and tow the light indicating full charge flickers on on off.
Yes, you can push the cart in both tow and run . Will reverse buzzer work in run but not in tow?
@waynemartin.waynesgolfcart4900 yes it does buzz when hitting the reverse side. However it buzzes, the voltage indicator drops where it is not visible. Of the cart. After a while it will go through the same sequences.
Wow! Valuable information. Thanks for sharing with us and being so clear.
Nice.
I have a 2007 precedent , bought new trojan batteries , plugged the cart in and left it for 20 hours or so and came out to the garage with the batteries boiling over and rotten egg smell
Egg smell is not uncommon. However if charger ran for more than 16 hours, that's a problem. Either the obc is bad, the charger has been bypassed, or you have the wrong charger.
Must be OBC ,,I have had the cart for 10 years and the same charger the whole time and never had an issue. Thank you for the quick reply! 🤠
Is there a way to test the OBC?I am proficient with a muti-meter
Easiest way is to try your charger on someone else's cart and try someone else's charger on your cart. That will tell you whether the problem is in your charger. Or your cart for sure before you replace anything..