I have a ps4 slim it shuts down after 5 to 10 minutes of game play. What could be the problem
@pjmsncaКүн бұрын
Good day friend, do you know that I bought that chip but it doesn't say Panasonic but the model is the same no matter what it says Panasonic is the same friend?
@Kieltec19 сағат бұрын
Nuvoton is also compatible with the Panasonic chip
@user-xg2ee2ds7s27 күн бұрын
👍👍
@emmanuelkoranteng2492Ай бұрын
Bro why didntyou start from the beginning like how to solder the points on the PS4 motherboard Uart points
@umarfarooq7291Ай бұрын
good job bro
@Trucam20202 ай бұрын
If I may say you must use a small tip soldering iron for smd soldering
@xx_ars_enic_xx28312 ай бұрын
When i try to tin my pads its struggling 😩 what to do i see you use some big blade looking solder tip?
@Kieltec2 ай бұрын
Buy a k-type tip for your iron Also pre -heat your motherboard it make it easier www.google.com/imgres?imgurl=https%3A%2F%2Fhakko.com.sg%2Fcdn%2Fshop%2Fproducts%2FT18-K.png%3Fv%3D1616573872%26width%3D1946&tbnid=2sBuQz4lXVLW9M&vet=1&imgrefurl=https%3A%2F%2Fhakko.com.sg%2Fproducts%2Ft18-k&docid=9Lf3AJpWy6lTSM&w=1946&h=1946&source=sh%2Fx%2Fim%2Fm4%2F2&kgs=a34a6cbc1945572b&shem=abme%2Cssic%2Ctrie#vhid=2sBuQz4lXVLW9M&vssid=l
@xx_ars_enic_xx28312 ай бұрын
@Kieltec I have that k type it picks up more soder from the pads then what it seems to be putting down
@constantlychangin2 ай бұрын
Hey could you upgrade the ram with higher capcity without messing too much up? Would you need to upgrade your accompaning componets (capacitors im guessing or not really as long as its gddr4?
@Kieltec2 ай бұрын
Yes If the pinout is the same maybe upgrading some resistors will be needed
@hsp13162 ай бұрын
I have a faulty adp-160er with damaged dnp012ah. However i only have dnp012a (i think from an adp-200). Are they both the same?
@Kieltec2 ай бұрын
I never tried that but it might work
@hsp13162 ай бұрын
@@Kieltec I replaced with dnp012a and it is working. Thanks 👍
@Heinrich.Fourie2 ай бұрын
Hi what type of microscope and model do you use if i may ask, Thanks for the video.
@Kieltec2 ай бұрын
Cat s62 pro
@rockzwave44072 ай бұрын
Can u put the same voltage transformer instead of this power supply unit?
@Kieltec2 ай бұрын
If you can replicate the needed voltages maybe it will work
@sualoabluetoothsualoabluet31582 ай бұрын
i have z906 ,light 5 and aux, help me
@randomguy35442 ай бұрын
Glad there won't be an explosion 😂
@JuanGomez092 ай бұрын
Hello, you know this mettod can solve code e101 90060007 8b05000f ? I have an xbox one s that it dont want update/install system, tried with different hdd, different cables and hdd adapter , resolder sata connectors and dvd drive appears be functional in other console (obviously cant initialize games)
@Kieltec2 ай бұрын
This will solve these errors only if the issues are on the Nand, Disc drive or Cpu related
@zaidkadwa12902 ай бұрын
did you use a bga stencil to reball the donor chips
@Kieltec2 ай бұрын
Yes a standard 0.5 stencil
@zaidkadwa21592 ай бұрын
@@KieltecAnd temperature of your station?
@ahmedabes31552 ай бұрын
😊❤
@Leeutjie3 ай бұрын
Is there anyway of me using a Xbox 360 power supply? modify and use on the xbos 1s because they both give out 12V 10A???
@Kieltec3 ай бұрын
It should work as long as it's 12v with enough amps
@Console_Tech3 ай бұрын
Good work buddy 😊 You might need another tweezers to get the job done.
@leonardolarosa28763 ай бұрын
Video utilissimo. Grazie
@user-vq1mk4un5f3 ай бұрын
Tanks
@kanuh3 ай бұрын
burnt af
@trendingfootshorts3 ай бұрын
Hello bro u did good work. I want to know wich size of ball for ram?
@karlhartl73713 ай бұрын
0.45
@Kieltec3 ай бұрын
0.5 with a standard stencil With a Ram stencil 0.45
@luiscastro20203 ай бұрын
which models is the power supply?
@irfantamboli97233 ай бұрын
Give varistor value
@Kieltec3 ай бұрын
3.3k resistors on primary 3w 5R6 on secondary
@Hasanzu0174 ай бұрын
🙏
@TorusHyperV4 ай бұрын
What thermal camera do you use?
@Kieltec4 ай бұрын
S62 Pro cat phone
@TorusHyperV4 ай бұрын
@@Kieltec thank you
@TorusHyperV4 ай бұрын
You're a great professional
@kondwanibanda42194 ай бұрын
Mine has a short on pin 9 and 16 on DDA001AG IC IS THAT NORMAL OR THE IC IS FAULTY
@Kieltec4 ай бұрын
Faulty Also check the 2 mosfets it drives
@kondwanibanda42194 ай бұрын
They are all good thanx for the reply sir
@Sonic29034 ай бұрын
Thank you for this video!
@irfantamboli97234 ай бұрын
Sir give part details i have same issue
@Kieltec4 ай бұрын
Which one?
@halsolution4 ай бұрын
@@Kieltec we also have the same issue of not powering on
@irfantamboli97233 ай бұрын
@@Kieltec no power on
@xx_ars_enic_xx28314 ай бұрын
Where do we learn where to test points and how to do voltage injection?
@xx_ars_enic_xx28314 ай бұрын
Big sound issues 😢can't hear anything
@ANTIGANG_4 ай бұрын
Awesome thanks you
@aficionalaelectronica4 ай бұрын
Porfa buen dia informacion sobre el Q802 de esa fuente
@xx_ars_enic_xx28314 ай бұрын
How did you know which Ram was faulty as the uRt did not tell you?
How do you do the voltage injection can you please make video to show
@Kieltec4 ай бұрын
watch this video kzread.info/dash/bejne/foR2xK5-lK-TqrQ.html
@xx_ars_enic_xx28315 ай бұрын
Where you from bro what country
@phynx-victumterra6525 ай бұрын
Any chance you know what would cause every memory channel to come up as disabled in Uart on a ps4 original?
@Kieltec5 ай бұрын
Check the fuse close to the fan connector
@ArekJP5 ай бұрын
Hello. amazing work! Question: I had an idea of swapping Nand on Xbox One S. I do have working board (fixed it) but no CD drive, so it wont update - will stuck on E100. The other board is probably unfixable but I have matching CD drive. I was thinking of swapping Nand from non working board onto working one, but after watching you video I'm assuming its not that simple as nand is linked as well with CPU/ GPU? Could you please advise. Many thanks.
@Kieltec5 ай бұрын
Hi I have a video on it check the link kzread.info/dash/bejne/dqCptrOPaNvbfps.html
@ArekJP5 ай бұрын
@@Kieltec Thanks for the reply. I have already watched it. Is there a way to determine that I have good APU/CPU ? I have few boards and resistance on V_GFXCORE values between 0.8 to 1.2 ohms and V_CPUCORE values between 1.5 to 2.5 ohms… Many thanks
@wiedzmin30505 ай бұрын
Hello, I see that You fixed it. I wanted to ask, have You ever had a problem with the control panel in these Logitech Z906s? Would You maybe have an idea what could have gone wrong? The lights of the 2.1>4.1>5.1 stereo side are changing by themselves (they are constantly selected by themselves). What could be the reason for this? Could this be fixed somehow? Yes, it generally works normally, but it constantly changes which speakers the sound goes to. Thank You in advance for reading and I wish You successful further repairs!
@Kieltec5 ай бұрын
Check on the power supply side Where i bridge those resistors if the trace is ok
@wiedzmin30505 ай бұрын
@@Kieltec Is the power in the control panel? To make things easier, I will add another control console, the problem does not occur. Do you have any other ideas for this control panel? There is a short circuit somewhere or something, the problem does not occur all the time, only from time to time, even heating the speakers does not cause a problem. Thank You in advance for Your answer.
@kasulepatrick55865 ай бұрын
Hlo mine powers off in seconds, i checked and saw that the 12v does not reach what could be the reason
@Kieltec5 ай бұрын
Try injecting 7 volts to dda001g see if there's drawing then replace it
@user-xn6bj4zt7l5 ай бұрын
Ps5 Hello, question: A short is occurring in two 13-pin capacitors on the DA9801 around the SSD. After removing the 13-pin capacitor, there is no short in the capacitor. It is grounded on the board, but all fuses are not disconnected on the board where the short occurred. Please help.
@Sonic29035 ай бұрын
Nice, but I think you forget to plug the wired at 15:19 lol the one that looks like a wifi or bluetooth wired
@Fevwy5 ай бұрын
How do u properly discharge the capacitors?
@ANTIGANG_5 ай бұрын
Nice fix
@firat.18666 ай бұрын
I replaced hdmi port and chip and check any components short circuit but i have always no signal, when i turn tv on the ps5 turn automatically on but i have always no signal.
@Kieltec5 ай бұрын
Check the diodes or filters if you have all needed voltages present
@firat.18665 ай бұрын
@@Kieltec i checked all lines and voltages everything looks ok but no signal, i try it with different hdmi cable with same Problem
@konradbaszczak36756 ай бұрын
hello, do you have a link or share the validator, I need it for single use
@TVHOGAR666 ай бұрын
Hello my dear frend, remember to apply heat from bottom of the pcb to remove nand flash. You also need to put the series x nand flash into another 1tb nvme also because of the controller that is designed for 1tb
@xx_ars_enic_xx28316 ай бұрын
Good to make a video but if you dont show your technique how you floating your ic on then its a bit pointless buds lol
@technicalmoreteam7 ай бұрын
Why du you make a bridge between r79 and r80?
@Kieltec6 ай бұрын
Thatt trace was broken even though it tested good i wouldn't trust it
Пікірлер
I have a ps4 slim it shuts down after 5 to 10 minutes of game play. What could be the problem
Good day friend, do you know that I bought that chip but it doesn't say Panasonic but the model is the same no matter what it says Panasonic is the same friend?
Nuvoton is also compatible with the Panasonic chip
👍👍
Bro why didntyou start from the beginning like how to solder the points on the PS4 motherboard Uart points
good job bro
If I may say you must use a small tip soldering iron for smd soldering
When i try to tin my pads its struggling 😩 what to do i see you use some big blade looking solder tip?
Buy a k-type tip for your iron Also pre -heat your motherboard it make it easier www.google.com/imgres?imgurl=https%3A%2F%2Fhakko.com.sg%2Fcdn%2Fshop%2Fproducts%2FT18-K.png%3Fv%3D1616573872%26width%3D1946&tbnid=2sBuQz4lXVLW9M&vet=1&imgrefurl=https%3A%2F%2Fhakko.com.sg%2Fproducts%2Ft18-k&docid=9Lf3AJpWy6lTSM&w=1946&h=1946&source=sh%2Fx%2Fim%2Fm4%2F2&kgs=a34a6cbc1945572b&shem=abme%2Cssic%2Ctrie#vhid=2sBuQz4lXVLW9M&vssid=l
@Kieltec I have that k type it picks up more soder from the pads then what it seems to be putting down
Hey could you upgrade the ram with higher capcity without messing too much up? Would you need to upgrade your accompaning componets (capacitors im guessing or not really as long as its gddr4?
Yes If the pinout is the same maybe upgrading some resistors will be needed
I have a faulty adp-160er with damaged dnp012ah. However i only have dnp012a (i think from an adp-200). Are they both the same?
I never tried that but it might work
@@Kieltec I replaced with dnp012a and it is working. Thanks 👍
Hi what type of microscope and model do you use if i may ask, Thanks for the video.
Cat s62 pro
Can u put the same voltage transformer instead of this power supply unit?
If you can replicate the needed voltages maybe it will work
i have z906 ,light 5 and aux, help me
Glad there won't be an explosion 😂
Hello, you know this mettod can solve code e101 90060007 8b05000f ? I have an xbox one s that it dont want update/install system, tried with different hdd, different cables and hdd adapter , resolder sata connectors and dvd drive appears be functional in other console (obviously cant initialize games)
This will solve these errors only if the issues are on the Nand, Disc drive or Cpu related
did you use a bga stencil to reball the donor chips
Yes a standard 0.5 stencil
@@KieltecAnd temperature of your station?
😊❤
Is there anyway of me using a Xbox 360 power supply? modify and use on the xbos 1s because they both give out 12V 10A???
It should work as long as it's 12v with enough amps
Good work buddy 😊 You might need another tweezers to get the job done.
Video utilissimo. Grazie
Tanks
burnt af
Hello bro u did good work. I want to know wich size of ball for ram?
0.45
0.5 with a standard stencil With a Ram stencil 0.45
which models is the power supply?
Give varistor value
3.3k resistors on primary 3w 5R6 on secondary
🙏
What thermal camera do you use?
S62 Pro cat phone
@@Kieltec thank you
You're a great professional
Mine has a short on pin 9 and 16 on DDA001AG IC IS THAT NORMAL OR THE IC IS FAULTY
Faulty Also check the 2 mosfets it drives
They are all good thanx for the reply sir
Thank you for this video!
Sir give part details i have same issue
Which one?
@@Kieltec we also have the same issue of not powering on
@@Kieltec no power on
Where do we learn where to test points and how to do voltage injection?
Big sound issues 😢can't hear anything
Awesome thanks you
Porfa buen dia informacion sobre el Q802 de esa fuente
How did you know which Ram was faulty as the uRt did not tell you?
repair.wiki/w/Playstation_4_Fault_finding_with_UART
How do you do the voltage injection can you please make video to show
watch this video kzread.info/dash/bejne/foR2xK5-lK-TqrQ.html
Where you from bro what country
Any chance you know what would cause every memory channel to come up as disabled in Uart on a ps4 original?
Check the fuse close to the fan connector
Hello. amazing work! Question: I had an idea of swapping Nand on Xbox One S. I do have working board (fixed it) but no CD drive, so it wont update - will stuck on E100. The other board is probably unfixable but I have matching CD drive. I was thinking of swapping Nand from non working board onto working one, but after watching you video I'm assuming its not that simple as nand is linked as well with CPU/ GPU? Could you please advise. Many thanks.
Hi I have a video on it check the link kzread.info/dash/bejne/dqCptrOPaNvbfps.html
@@Kieltec Thanks for the reply. I have already watched it. Is there a way to determine that I have good APU/CPU ? I have few boards and resistance on V_GFXCORE values between 0.8 to 1.2 ohms and V_CPUCORE values between 1.5 to 2.5 ohms… Many thanks
Hello, I see that You fixed it. I wanted to ask, have You ever had a problem with the control panel in these Logitech Z906s? Would You maybe have an idea what could have gone wrong? The lights of the 2.1>4.1>5.1 stereo side are changing by themselves (they are constantly selected by themselves). What could be the reason for this? Could this be fixed somehow? Yes, it generally works normally, but it constantly changes which speakers the sound goes to. Thank You in advance for reading and I wish You successful further repairs!
Check on the power supply side Where i bridge those resistors if the trace is ok
@@Kieltec Is the power in the control panel? To make things easier, I will add another control console, the problem does not occur. Do you have any other ideas for this control panel? There is a short circuit somewhere or something, the problem does not occur all the time, only from time to time, even heating the speakers does not cause a problem. Thank You in advance for Your answer.
Hlo mine powers off in seconds, i checked and saw that the 12v does not reach what could be the reason
Try injecting 7 volts to dda001g see if there's drawing then replace it
Ps5 Hello, question: A short is occurring in two 13-pin capacitors on the DA9801 around the SSD. After removing the 13-pin capacitor, there is no short in the capacitor. It is grounded on the board, but all fuses are not disconnected on the board where the short occurred. Please help.
Nice, but I think you forget to plug the wired at 15:19 lol the one that looks like a wifi or bluetooth wired
How do u properly discharge the capacitors?
Nice fix
I replaced hdmi port and chip and check any components short circuit but i have always no signal, when i turn tv on the ps5 turn automatically on but i have always no signal.
Check the diodes or filters if you have all needed voltages present
@@Kieltec i checked all lines and voltages everything looks ok but no signal, i try it with different hdmi cable with same Problem
hello, do you have a link or share the validator, I need it for single use
Hello my dear frend, remember to apply heat from bottom of the pcb to remove nand flash. You also need to put the series x nand flash into another 1tb nvme also because of the controller that is designed for 1tb
Good to make a video but if you dont show your technique how you floating your ic on then its a bit pointless buds lol
Why du you make a bridge between r79 and r80?
Thatt trace was broken even though it tested good i wouldn't trust it