wax lol ,,,, try acf 50 ,,, I wouldnt use wax ever.
@Bzapp7258 ай бұрын
Cavity wax is not actually wax... It's what car manufacturers recommend for their vehicles
@tomthompson74008 ай бұрын
@@Bzapp725 and if it worked you wouldnt be repairing them in the first place ,,,, Waxol is mainly palm oil as an example ,,
@Bzapp7258 ай бұрын
@@tomthompson7400 It definitely works. If you have a Volkswagen made car they cavity wax it liberally thus the unibody seldom ever rusts in it's lifetime. You must repair a car as in test #2 in collision repair sometimes...
@tomthompson74008 ай бұрын
@@Bzapp725 lol where in the world are you ,,, round here you sweep up wheel arches and sills after heavy rain ... mind you . I make a handsome living welding land rovers ,, long live rust.
@Bzapp7258 ай бұрын
@@tomthompson7400 great!
@garethjudd58408 ай бұрын
Transtar is brilliant.The results are fabulous rainbows 🌈 😂
@rc38318 ай бұрын
did you shake the cans more than 2-3 seconds as shown? What was in your rusting solution?
@Bzapp7258 ай бұрын
I believe they were well agitated... I always tend to shake a can regardless of if it needs it... the solution was vinegar, water, and salt
@mrsa10111 ай бұрын
funny. you could wipe the rust off on the fluid film side but not on the pb side???? after using both on my jeep im going back to fluid film. i see more rust after 11 months . the pb still to this day drips on my drive way on hot days and the smell was terrible for weeks after application
@Bzapp72511 ай бұрын
It was brown with pb but not rusty. FF definitely smells but I did not spray a lot of pb. FF works but does wash off pretty soon.
@toastrecon9 ай бұрын
Huh. I just sprayed mine with Surface Shield with the garage door open and it doesn’t even really smell? I’ll have to see if it drips on hot days. I didn’t spray it on too thick
@josephpuchel6497 Жыл бұрын
Hey There’s also Petroleum Products rust proofing. It’s petroleum based with additional ingredients. It creeps, sticks never hardens. Probably never wash off . Excellent product.
@g.fortin3228 Жыл бұрын
I'd use angle iron remove the millscale.. not a sanded but previously treated panel. ;- ) that said, the PB sure doesn't smell as bad and does resist being washed off better.
@tjrick7745 Жыл бұрын
interesting results. Maybe should have sprayed top to bottom vs right to left? I'm wondering home much fluid film ended up in the PB SS side of the test? One reason I like FF over a few of the others competing lanoline and grease type products is that you can pressure wash off an area you want to work on to get less dirty, then re-apply. WW SS FF NHOU all have pros and cons to me, but I like them all.
@Bzapp725 Жыл бұрын
Right, top to bottom would have been better but wasn't significant imo. Hadn't thought about having to wash it off. It's a nice idea.
@smokingmother Жыл бұрын
lmfao at less dirty soap is cheap cars are not
@bigbonede62014 жыл бұрын
nice 240p
@craiggerlach55485 жыл бұрын
I find the QC of the destroyer to be total fail.. 1 in 20 fit my weapon, 17 of 20 I can fire if I push them into barrel with small tool, other 2 are deformed such that I would have to file them to get them to fit.. The issue nearly all resides in the tail of the projectile,, only a few had tip distorted, if I get my reloading gear out will mic these to see what the problem is.. Guess the red squirrels get a pass at the feeder this week as this is all we can buy locally...
@mr.bossman62479 жыл бұрын
show the whole gun wat type is it
@amelierenoncule9 жыл бұрын
As I suspected.
@neilmoomey10 жыл бұрын
Nice shooting. Your accuracy roughly declined with your psi. You should have switched pellets on each shot for a better test. Each Mrod has accuracy nodes unique to that gun. Changes in the wind could have also been responsible for the results.
@Bzapp72510 жыл бұрын
You got that right it changes like the wind. I think I think had it tuned for 20 shots within 20 psi but I never shot the baracudas as good since.
@jo1777710 жыл бұрын
dude hid the bird with a kill shot or dont hid it but dont shoot it when you're a bad shooter.... just useless.
@Bzapp72510 жыл бұрын
I find it very useful but yeah, the thing isn't very accurate. Iv'e moved on to pcp(marauder).
@TheMagicalPonyBrony10 жыл бұрын
Dint*
@TheMagicalPonyBrony10 жыл бұрын
Its called a indent, dent or fint. Not indention
@Bzapp72511 жыл бұрын
I't sounds as though your barrel has leaded up. Search Airgunweb on youtube and find a video on how to clean the barrel. Rick is his name, he has lots of good info and will answer question.
@Killuminati78511 жыл бұрын
My phantom has gone really inaccurate, I've tried zeroing out the scope but it keeps shooting in different places, btw its not the pellets because it was working fine before with the pellets. Have any suggestions?
@Bzapp72511 жыл бұрын
Don't know what to tell you, it's likely but pretty much of a crapshoot.
@doblar1511 жыл бұрын
ive got the same rifle as you but the .22 model. do you think the jsb's will work well in the .22 aswell ?
@Bzapp72511 жыл бұрын
I agree with everything except the first part. I was trying to do a one shot kill; but I don't think you know much about cheap airguns...they just are not very accurate. That's why I got a marauder
@metallican229511 жыл бұрын
Dude u suck...if you're gonna do pest control at least try a one shot one kill...stop aiming for a headshot its easier and just as deadly to do a heart or lung shot
@Bzapp72511 жыл бұрын
It is a good bit loud, but I did not notice it get quieter a after break in. Thanks
@lutlut18711 жыл бұрын
Why is your rifle so loud, after break-in period it should have quieted down? Nice shooting any way!
@Bzapp72511 жыл бұрын
The higher price usually contributes to higher build quality, better fit & finish, function, and above all accuracy. If your looking at getting a low priced springer for less than $150 the Gamo Big Cat would likely be a good choice. Check out Rick Hustler's reviews , he has a channel: AirGunWeb on KZread.
@Mikenopolis11 жыл бұрын
if two guns both have the same FPS, shot the same pellets what makes one better than the other? I'm looking getting my first rifle (I've had plenty of pistols) but going to start of with $150 spring rifle (Gamo Whispers or Crosman/Benjamin Nitro Pistons) they all have about 900-1000fps what makes the $300,$500, thousand dollar ones THAT much better? should't the same fps + pellet size/weight pierce the same? PCP is not an option for me...yet
@Bzapp72511 жыл бұрын
A direct lung shot or a spine shot will work just as well as a head shot and is easier to get. Also, a more accurate gun and a bigger caliber will help.
@TheReem50611 жыл бұрын
just go up to it when it was still on the ground and snap its head. only way so it doesnt suffer
@semtech3011 жыл бұрын
Just got some new crossman hunter pellets and destroyers. My digital scale weighed them at 7.4 gr. Light but fast. Wish they had a bit larger skirt on them but they'll do the job.
@dmo8482 жыл бұрын
Try Gamo hunter pellets. You'll love em but allot of bent up in tin
@nunnyd6911 жыл бұрын
From what i found, the wadcutters are best suited to either smaller vermin (rats and pigeon sizes) at shorter ranges of 20 to 30 metres for a clean kill as they devastate when they hit bone but they lose power and accuracy at longer ranges. The pointed are best suited to larger vermin (rabbit sized) at longer ranges for penetrating skulls, while the domed seem a good all rounder at short to medium range 20 to 50 metres they still hit the target hard plus remain fairly accurate.
@dmo8482 жыл бұрын
Jus what I needed to know. Thank u
@nunnyd6911 жыл бұрын
I used 3 differnet type of .22 pellets at 20 metres (RWS hobby wadcutter, Daystate Li domed; and Bisley Premier pointed) on a potato and a raw chicken leg that had gone bad to try and simulate the effects they had on live quarry. The wadcutters transfer most of their energy into the target splitting the potatoes and making the largest exit wounds in the potato and chicken the domed did similar with a smaller exit wound and the pointed produced the smallest exit wound but had greatest penetration
@Bzapp72511 жыл бұрын
You need a scope that is shockproof. I use and recommend the utg 4x32 mil dot scope. If you would like variable power go for their 3-9x32 scope. Thanks for the nice words I appreciate it xd!
@zacksmith840511 жыл бұрын
Hey I also have phantom but I need a scope. What scope should I get?? And nice vids.
@Bzapp72511 жыл бұрын
Actually I do both, sortv'e. I shoot random starlings and they are a rather invasive species.
@Bzapp72512 жыл бұрын
Crosman Phantom
@Scmidster12 жыл бұрын
I love these video
@bammbammcali12 жыл бұрын
Nice...
@Bzapp72512 жыл бұрын
Yeah, I tuned it using the hammer spring, the hammer throw, and the transfer port. I used a method I found on marauder air rifle.com. I came up with a 34 fps spread using h&n barracudas, shooting them at 827 fps avg. 20 shots from: 2700-2100 psi.
@rodambluc12 жыл бұрын
If you want more power open her up, but you will have less shots. if you like how many shots you are getting right now then keep it the same. I do think you can still get more out of you gun. Have you changed the Hammer spring?
@Bzapp72512 жыл бұрын
I recently tuned mine up a bit. Now I shoot 21.14s at avg. 827 fps. which gives me 32 ft. lbs. This is about the going rate from what I read on the forums, of course I have a .22 so is that possible with mine?
@Bzapp72512 жыл бұрын
Try Crosman Premier or JSB exact, have had my best results with them.
@brennannolan130112 жыл бұрын
hey um im getting the crosman phantom what pellets should i use any answers?
Пікірлер
wax lol ,,,, try acf 50 ,,, I wouldnt use wax ever.
Cavity wax is not actually wax... It's what car manufacturers recommend for their vehicles
@@Bzapp725 and if it worked you wouldnt be repairing them in the first place ,,,, Waxol is mainly palm oil as an example ,,
@@tomthompson7400 It definitely works. If you have a Volkswagen made car they cavity wax it liberally thus the unibody seldom ever rusts in it's lifetime. You must repair a car as in test #2 in collision repair sometimes...
@@Bzapp725 lol where in the world are you ,,, round here you sweep up wheel arches and sills after heavy rain ... mind you . I make a handsome living welding land rovers ,, long live rust.
@@tomthompson7400 great!
Transtar is brilliant.The results are fabulous rainbows 🌈 😂
did you shake the cans more than 2-3 seconds as shown? What was in your rusting solution?
I believe they were well agitated... I always tend to shake a can regardless of if it needs it... the solution was vinegar, water, and salt
funny. you could wipe the rust off on the fluid film side but not on the pb side???? after using both on my jeep im going back to fluid film. i see more rust after 11 months . the pb still to this day drips on my drive way on hot days and the smell was terrible for weeks after application
It was brown with pb but not rusty. FF definitely smells but I did not spray a lot of pb. FF works but does wash off pretty soon.
Huh. I just sprayed mine with Surface Shield with the garage door open and it doesn’t even really smell? I’ll have to see if it drips on hot days. I didn’t spray it on too thick
Hey There’s also Petroleum Products rust proofing. It’s petroleum based with additional ingredients. It creeps, sticks never hardens. Probably never wash off . Excellent product.
I'd use angle iron remove the millscale.. not a sanded but previously treated panel. ;- ) that said, the PB sure doesn't smell as bad and does resist being washed off better.
interesting results. Maybe should have sprayed top to bottom vs right to left? I'm wondering home much fluid film ended up in the PB SS side of the test? One reason I like FF over a few of the others competing lanoline and grease type products is that you can pressure wash off an area you want to work on to get less dirty, then re-apply. WW SS FF NHOU all have pros and cons to me, but I like them all.
Right, top to bottom would have been better but wasn't significant imo. Hadn't thought about having to wash it off. It's a nice idea.
lmfao at less dirty soap is cheap cars are not
nice 240p
I find the QC of the destroyer to be total fail.. 1 in 20 fit my weapon, 17 of 20 I can fire if I push them into barrel with small tool, other 2 are deformed such that I would have to file them to get them to fit.. The issue nearly all resides in the tail of the projectile,, only a few had tip distorted, if I get my reloading gear out will mic these to see what the problem is.. Guess the red squirrels get a pass at the feeder this week as this is all we can buy locally...
show the whole gun wat type is it
As I suspected.
Nice shooting. Your accuracy roughly declined with your psi. You should have switched pellets on each shot for a better test. Each Mrod has accuracy nodes unique to that gun. Changes in the wind could have also been responsible for the results.
You got that right it changes like the wind. I think I think had it tuned for 20 shots within 20 psi but I never shot the baracudas as good since.
dude hid the bird with a kill shot or dont hid it but dont shoot it when you're a bad shooter.... just useless.
I find it very useful but yeah, the thing isn't very accurate. Iv'e moved on to pcp(marauder).
Dint*
Its called a indent, dent or fint. Not indention
I't sounds as though your barrel has leaded up. Search Airgunweb on youtube and find a video on how to clean the barrel. Rick is his name, he has lots of good info and will answer question.
My phantom has gone really inaccurate, I've tried zeroing out the scope but it keeps shooting in different places, btw its not the pellets because it was working fine before with the pellets. Have any suggestions?
Don't know what to tell you, it's likely but pretty much of a crapshoot.
ive got the same rifle as you but the .22 model. do you think the jsb's will work well in the .22 aswell ?
I agree with everything except the first part. I was trying to do a one shot kill; but I don't think you know much about cheap airguns...they just are not very accurate. That's why I got a marauder
Dude u suck...if you're gonna do pest control at least try a one shot one kill...stop aiming for a headshot its easier and just as deadly to do a heart or lung shot
It is a good bit loud, but I did not notice it get quieter a after break in. Thanks
Why is your rifle so loud, after break-in period it should have quieted down? Nice shooting any way!
The higher price usually contributes to higher build quality, better fit & finish, function, and above all accuracy. If your looking at getting a low priced springer for less than $150 the Gamo Big Cat would likely be a good choice. Check out Rick Hustler's reviews , he has a channel: AirGunWeb on KZread.
if two guns both have the same FPS, shot the same pellets what makes one better than the other? I'm looking getting my first rifle (I've had plenty of pistols) but going to start of with $150 spring rifle (Gamo Whispers or Crosman/Benjamin Nitro Pistons) they all have about 900-1000fps what makes the $300,$500, thousand dollar ones THAT much better? should't the same fps + pellet size/weight pierce the same? PCP is not an option for me...yet
A direct lung shot or a spine shot will work just as well as a head shot and is easier to get. Also, a more accurate gun and a bigger caliber will help.
just go up to it when it was still on the ground and snap its head. only way so it doesnt suffer
Just got some new crossman hunter pellets and destroyers. My digital scale weighed them at 7.4 gr. Light but fast. Wish they had a bit larger skirt on them but they'll do the job.
Try Gamo hunter pellets. You'll love em but allot of bent up in tin
From what i found, the wadcutters are best suited to either smaller vermin (rats and pigeon sizes) at shorter ranges of 20 to 30 metres for a clean kill as they devastate when they hit bone but they lose power and accuracy at longer ranges. The pointed are best suited to larger vermin (rabbit sized) at longer ranges for penetrating skulls, while the domed seem a good all rounder at short to medium range 20 to 50 metres they still hit the target hard plus remain fairly accurate.
Jus what I needed to know. Thank u
I used 3 differnet type of .22 pellets at 20 metres (RWS hobby wadcutter, Daystate Li domed; and Bisley Premier pointed) on a potato and a raw chicken leg that had gone bad to try and simulate the effects they had on live quarry. The wadcutters transfer most of their energy into the target splitting the potatoes and making the largest exit wounds in the potato and chicken the domed did similar with a smaller exit wound and the pointed produced the smallest exit wound but had greatest penetration
You need a scope that is shockproof. I use and recommend the utg 4x32 mil dot scope. If you would like variable power go for their 3-9x32 scope. Thanks for the nice words I appreciate it xd!
Hey I also have phantom but I need a scope. What scope should I get?? And nice vids.
Actually I do both, sortv'e. I shoot random starlings and they are a rather invasive species.
Crosman Phantom
I love these video
Nice...
Yeah, I tuned it using the hammer spring, the hammer throw, and the transfer port. I used a method I found on marauder air rifle.com. I came up with a 34 fps spread using h&n barracudas, shooting them at 827 fps avg. 20 shots from: 2700-2100 psi.
If you want more power open her up, but you will have less shots. if you like how many shots you are getting right now then keep it the same. I do think you can still get more out of you gun. Have you changed the Hammer spring?
I recently tuned mine up a bit. Now I shoot 21.14s at avg. 827 fps. which gives me 32 ft. lbs. This is about the going rate from what I read on the forums, of course I have a .22 so is that possible with mine?
Try Crosman Premier or JSB exact, have had my best results with them.
hey um im getting the crosman phantom what pellets should i use any answers?
beautiful view