hi, I don't know. I weigh 110 kg and train around 100 kg, so 210 kg is no problem🤣
@victorcaramon747713 күн бұрын
Thank you for you video ! Do you have an schematic that you can share?
@uncle_maik13 күн бұрын
No, sorry. Unfortunately only the dimensions in the video.
@jyothiravi917513 күн бұрын
What is the length of the leg?? It is not mentioned at the last
@uncle_maik13 күн бұрын
Hi, I made it 45 cm. The exact measurement is not important. Good luck with your reconstruction and good workouts later
@dorothyaboagye967918 күн бұрын
Excellent video . Please can you give out the dimensions. Thanks
@uncle_maik18 күн бұрын
Thanx. You can find the dimensions at the end of the Video.
@SyedAbdulSattar-cs3nnАй бұрын
Bench size how much that black iscale how much size
@uncle_maikАй бұрын
hi the dimensions can be found at the very end of the video.
@tvbox-df7spАй бұрын
Excellent work friend, could you give me the measurements to try to do this work that was done with excellence?
@uncle_maikАй бұрын
Hi, I no longer have a blueprint. but from minute 19:35 you will find everything.
@bamboo9840Ай бұрын
Alter, dein Kanal ist ja eine richtige Goldmine für DIY Equipment. Leistest wirklich gute Arbeit! Habe auch bereits über ein kleines Rack nachgedacht, aber die Gegebenheiten im Lehm-Altbau mit niedrigem/kleinen Keller erschweren das doch so ziemlich. Für die ganzen Löcher wäre eine günstige Magnetbohrmaschine natürlich wesentlich angenehmer :D
@uncle_maikАй бұрын
Hi, danke schön. Freut mich, wenn andere dadurch inspiriert werden. Heute kommt ein neues Video, und das nächste Projekt ist im Bau- Ideen von der Fibo mitgebracht. Geräte könnte ich so einiges noch gebrauchen😂 hab mir zumindest ein neues Schweißgerät gekauft, weil es mitten in diesem Projekt platt war- war vom Schwiegervater und knapp 20 Jahre alt. Viel Erfolg bei deinem Projekt-gerade bei niedrigen Decken findet man nix zum Kauf.
@bamboo9840Ай бұрын
@@uncle_maik Top, darauf bin ich schon mal gespannt! Habe auch mal die Glocke aktiviert :D Shit, welches Schweißgerät hast du dir denn gekauft? Ich wollte mir demnächst auch mal ein kleines Elektroden-Schweißgerät zulegen, bin aber noch am abwägen/recherchieren. Budget ist dank Studium etwas schmal bemessen 😁
@uncle_maikАй бұрын
Ein ganz einfaches von Aldi bei Ebay Kleinanzeigen für 80,- geschossen. Mit Lüfter- mehr brauche ich nicht. Außer es ist was besonderes (siehe Safety Squat Bar), dann leihe ich mir ein WIG vom Kollegen.
@tammolenger304Ай бұрын
Respekt!
@uncle_maikАй бұрын
Danke schön.
@armandoemilianocaraballo30452 ай бұрын
Muy buen trabajo, y gracias por compartir. Queria saber que medidas de caño estructural usaste?
@uncle_maik2 ай бұрын
Muchas gracias. Son tubos de 60 x 60 mm con un espesor de 3 mm.
@odn77692 ай бұрын
richtig geil
@uncle_maik2 ай бұрын
Danke😉
@antoniopedrosa532 ай бұрын
Show parabéns pelo trabalho
@uncle_maik2 ай бұрын
Obrigado por seu comentário
@technicalchhora2 ай бұрын
Hight of
@hanswestmar34502 ай бұрын
Geil! Überlege gerade, mir welche zu holen und da wurde mir beim Recherchieren dein Video vorgeschlagen. Respekt für die Arbeit, ich hab leider zwei linke Hände :D
@uncle_maik2 ай бұрын
Danke schön. Lass aber die Finger von den Dingern... sieht gut aus, ist aber bei schwereren KH, und dafür sind sie ja..., echt unangenehm in der Handinnenfläche. Hab die Dinger umgebaut, und nutze sie nur noch als Halter. Hab Zurrgurte und Ketten genommen, um sie zu sichern. Vlt. Mache ich dazu noch ein Video- ist echt einfach. Guten Pump
@hanswestmar34502 ай бұрын
@@uncle_maik ach schade, vor allem das Umsetzen mit beladbaren Hanteln ist absolut bescheiden. Aber danke für deine Info. Bin auf weitere Homegym Videos gespannt.
@uncle_maik2 ай бұрын
@@hanswestmar3450hab sie als Aufhängung umfunktioniert. Dann ist es angenehmer. Vlt. Mache ich dazu auch noch ein Video vG
@ronydm23252 ай бұрын
Dimensions plz
@SyedAbdulSattar-cs3nn3 ай бұрын
Bench height how much it is
@uncle_maik3 ай бұрын
hi the dimensions can be found at the very end of the video.
@yasartvmАй бұрын
Where
@yasartvmАй бұрын
Bench height how much
@sherzodbekganiyov18823 ай бұрын
Привет ты гений
@uncle_maik3 ай бұрын
Thanx😀
@p4ulets3 ай бұрын
Monstro!!!😀
@uncle_maik3 ай бұрын
Thanx😊
@user-fv3xg5fe5n4 ай бұрын
Излишества которые приводят к удорожанию конструкции и абсолютно не влияют на надежность и экономию времени при занятии спортом !
@uncle_maik4 ай бұрын
What do you mean by that?! The translation according to Google somehow makes no sense...😅
@vv-cy5sk4 ай бұрын
Good! But bad for any from a market $100! )) Think 110kg max too!)
@uncle_maik4 ай бұрын
hi, what does the sentence with the 100 euros mean? I weigh 115 kg, train with a 120 kg bench... so 235 kg is fine. how much maximum... no idea. have a great pump
@manfredopablolopezmolina16194 ай бұрын
Thanks, ire por ello.
@uncle_maik4 ай бұрын
Good luck, and a great pump😀
@tolluka14 ай бұрын
Ese es soldador o herrero refinado...jeje que trabaja sobre alfombra. Sin quemarla. Jajajaja felicidades una buena obra.. puedes publicar los planos
@uncle_maik4 ай бұрын
gracias gracias - corté las manchas cuando se quemó la alfombra🤣 no, bromas aparte... Ya no tengo los planos, pero puedes encontrarlos al final del vídeo. Atentamente
@uncle_maik5 ай бұрын
Hi, you find it at Minute 19.00.
@sebasro92335 ай бұрын
Hallo, wie dick sind die Rohrwände? .
@uncle_maik5 ай бұрын
Hi, hab 3mm genommen. Ist perfekt. VG
@sebasro92335 ай бұрын
@@uncle_maik ok, danke, gutes Video
@uncle_maik5 ай бұрын
Danke schön
@fabiangrautmann5 ай бұрын
Welche profile hastdu genommen? 120x120x3?😊
@uncle_maik5 ай бұрын
Hi, hab 80x80x4 genommen. Würde es aber jetzt eher mit 60x60x oder 70x70 machen. 80x80 ist schon dick... stärke mit 3mm wäre mir zu dünn, 4mm geben mehr Gewicht und Stabilität. Viel Erfolg.
@der60er5 ай бұрын
hast du tipp wegen guten bohrern ? dein stufenbohrer scheint auch top zu sein.
@uncle_maik5 ай бұрын
Hi, hab alle Bohrer und auch den Stufenbohrer von Aldi oder Lidl. Bin mit der Qualität sehr zufrieden. Tausche die verbrauchten Bohrer einfach aus, bei dem Preis kaufe ich halt neue. VG
@user-md9pb8nj9i5 ай бұрын
Сборка на ковре? Ты сделал мой день!😂
@uncle_maik5 ай бұрын
Главное удобно🤣 и всякий раз, когда горело, я останавливала камеру😂🤣 большой привет
@ntbv59733 ай бұрын
I thought it was some kind of non-burning basalt carpet 😅
@uncle_maik3 ай бұрын
Yes😂😂
@esamhasanat94515 ай бұрын
Is there any micro movement to the right or lift ?
@uncle_maik5 ай бұрын
hi, the movement is very slight. no more than with a studio bench. Best regards
@jasonxu60435 ай бұрын
Very nice work. I'm about to make one, I wonder how much material it costs?
@uncle_maik5 ай бұрын
Thanx. You cn buy ist online, there is it cheap.Good look.
@jasonxu60435 ай бұрын
@@uncle_maik really? What is the web?
@uncle_maik5 ай бұрын
It's a german Steel Shop. But I think, there ist only shipping to germany...
@user-zp2yh6fk7t5 ай бұрын
Молодец !!!
@uncle_maik5 ай бұрын
Thanx😊
@user-zp2yh6fk7t5 ай бұрын
😅Молодец !!!
@uncle_maik5 ай бұрын
😊
@heru23366 ай бұрын
sir I watched a few DIY project videos which helped me a lot thank you for the videos good luck 💥 RESPECT SIR ❤🔥
@uncle_maik6 ай бұрын
Thank you very much and have fun and success with the reconstruction
@johnmackey79656 ай бұрын
What a great bench build, I was wondering if you could send me your plans, would like to build one
@uncle_maik6 ай бұрын
Hi, unfortunately I don't have a plan anymore. At the end of the video you will find the dimensions. good luck with the reconstruction
@Crime_pays6 ай бұрын
How much did it cost you in supplies
@al3xb8277 ай бұрын
Echt gut gemacht!
@uncle_maik7 ай бұрын
Danke schön.
@misaeltapia20087 ай бұрын
Excelente trabajo desde chile.. saludos.
@uncle_maik7 ай бұрын
Muchas gracias. saludos desde Alemania
@hansmeier59567 ай бұрын
Hi, ich finde es geil, dass hier mal einer DIY Videos macht mit Metall. Ich hole mir total viele Anregungen hier. Bitte mehr Videos! Geil finde ich auch das Mindset: Schieß drauf wie die Naht aussieht, funktionieren muss es!
@uncle_maik7 ай бұрын
Danke für dein Kompliment, außer für die Nähte😂 werden aber von Mal zu Mal besser😅 guck mal bei der Dip- Maschine... da bin ich schon ein wenig stolz😊 mit Ele ist das nicht so schön, bei der Safetysquatbar hatte ich die Gelegenheit, WIG zu schweißen- viel geiler... naja, hauptsache hält. Den Rest macht dann die Flex und der Lack. Guten Pump.
@tobiasbauer51758 ай бұрын
Ur coole Videos, mach ich auch so!! Mach weiter so!!
@uncle_maik8 ай бұрын
Danke schön. VG
@saitejagatadi97118 ай бұрын
The squares 11:55 that you have used can max load weight capacity of 150kg. How can we weld in a way to increase the max weight capacity to atleast 250kg if not 300kg
@uncle_maik8 ай бұрын
No risk no fun😂 i think, it is okay for more than 150 kg. But take bigger Steel-Plates.
@saitejagatadi97118 ай бұрын
@@uncle_maik haha okay sure.. Thank you
@Bubbaman10008 ай бұрын
wo bestellst du deinen Stahl, wegen den Versandkosten?
@uncle_maik8 ай бұрын
Hi, bisher immer bei Stahlshop24.de ging schnell und ist günstig. Viel Spaß beim Nachbau. VG
@AS-ug2vq8 ай бұрын
Good job bro!
@uncle_maik8 ай бұрын
Thanks! Get a great Pump!
@misaeltapia20089 ай бұрын
Excelente buen maestro.
@uncle_maik9 ай бұрын
😍
@Yannis20229 ай бұрын
Does this setup mean double the distance and half the weight when pulling?
@uncle_maik9 ай бұрын
Hi, if you pull from the top, you have 1:1. But if you pull from the floor, you have half weight and half distance. Look at the cables- you see the difference between the way. If you want it also by pulling from the top, you need an extra role between the weights and the first cable. Greetings from Germany
@Yannis20229 ай бұрын
@@uncle_maik Thanks for explaining, understood. Greetings from Sweden.
@doriantomas9 ай бұрын
10x 4 sharing man
@hadyblack98749 ай бұрын
How long iron in 3.40 mnt?
@uncle_maik9 ай бұрын
hi, the tubes are all 60 x 60 mm, one is 60 x 30 mm. in minute 20.33 you will find all the measurements. just zoom. good luck.
@hadyblack98749 ай бұрын
What Angle was it used? For foot and head?
@uncle_maik9 ай бұрын
@@hadyblack9874hi, you can snap it in every 5 cm and thus set various angles between 0 and 90 degrees at the head and between 0 and about 30 degrees at the foot. hi, you can snap it in every 5 cm and thus set various angles between 0 and 90 degrees at the head and between 0 and about 30 degrees at the foot. Hallo, man kann es alle 5 cm einrasten lassen und so verschiedene Winkel zwischen 0 und 90 Grad am Kopf und zwischen 0 und ca. 30 Grad am Fuß einstellen. hi, you can snap it in every 5 cm and thus adjust various angles between 0 and 90 degrees at the head and between 0 and around 30 degrees at the foot. Hallo, man kann es alle 5 cm einrasten und so verschiedene Winkel zwischen 0 und 90 Grad am Kopf und zwischen 0 und etwa 30 Grad am Fuß einstellen. Best regards
@spiderbull2749 ай бұрын
Im making the bench, but me and my dad made it uneven 😅
@uncle_maik9 ай бұрын
how exactly? if it's not level, put something under the pad and frame to make it level. I'll keep my fingers crossed for you, let me know if it fits. greetings from germany. 💪💪💪
@spiderbull2749 ай бұрын
@@uncle_maik Thank you for your greetings and your advice, its actually cause the ground we made it on Is uneven so it became uneven with it 😅🤣
@uncle_maik9 ай бұрын
@@spiderbull274 OK. flex and re-weld 🤣 but first bring it into balance. good pump after welding💪
@spiderbull2749 ай бұрын
@@uncle_maik 🤣💪
@supermendetekted10 ай бұрын
Сварка на ковре, красота)
@uncle_maik10 ай бұрын
лучше ковер сломан, чем пол 🤣😂
@Micky-MMK10 ай бұрын
Respekt! Kann man wirklich loben, wer solches Handwerk versteht! Chapeau! 🎩
Пікірлер
Cuantos kg soporta?
hi, I don't know. I weigh 110 kg and train around 100 kg, so 210 kg is no problem🤣
Thank you for you video ! Do you have an schematic that you can share?
No, sorry. Unfortunately only the dimensions in the video.
What is the length of the leg?? It is not mentioned at the last
Hi, I made it 45 cm. The exact measurement is not important. Good luck with your reconstruction and good workouts later
Excellent video . Please can you give out the dimensions. Thanks
Thanx. You can find the dimensions at the end of the Video.
Bench size how much that black iscale how much size
hi the dimensions can be found at the very end of the video.
Excellent work friend, could you give me the measurements to try to do this work that was done with excellence?
Hi, I no longer have a blueprint. but from minute 19:35 you will find everything.
Alter, dein Kanal ist ja eine richtige Goldmine für DIY Equipment. Leistest wirklich gute Arbeit! Habe auch bereits über ein kleines Rack nachgedacht, aber die Gegebenheiten im Lehm-Altbau mit niedrigem/kleinen Keller erschweren das doch so ziemlich. Für die ganzen Löcher wäre eine günstige Magnetbohrmaschine natürlich wesentlich angenehmer :D
Hi, danke schön. Freut mich, wenn andere dadurch inspiriert werden. Heute kommt ein neues Video, und das nächste Projekt ist im Bau- Ideen von der Fibo mitgebracht. Geräte könnte ich so einiges noch gebrauchen😂 hab mir zumindest ein neues Schweißgerät gekauft, weil es mitten in diesem Projekt platt war- war vom Schwiegervater und knapp 20 Jahre alt. Viel Erfolg bei deinem Projekt-gerade bei niedrigen Decken findet man nix zum Kauf.
@@uncle_maik Top, darauf bin ich schon mal gespannt! Habe auch mal die Glocke aktiviert :D Shit, welches Schweißgerät hast du dir denn gekauft? Ich wollte mir demnächst auch mal ein kleines Elektroden-Schweißgerät zulegen, bin aber noch am abwägen/recherchieren. Budget ist dank Studium etwas schmal bemessen 😁
Ein ganz einfaches von Aldi bei Ebay Kleinanzeigen für 80,- geschossen. Mit Lüfter- mehr brauche ich nicht. Außer es ist was besonderes (siehe Safety Squat Bar), dann leihe ich mir ein WIG vom Kollegen.
Respekt!
Danke schön.
Muy buen trabajo, y gracias por compartir. Queria saber que medidas de caño estructural usaste?
Muchas gracias. Son tubos de 60 x 60 mm con un espesor de 3 mm.
richtig geil
Danke😉
Show parabéns pelo trabalho
Obrigado por seu comentário
Hight of
Geil! Überlege gerade, mir welche zu holen und da wurde mir beim Recherchieren dein Video vorgeschlagen. Respekt für die Arbeit, ich hab leider zwei linke Hände :D
Danke schön. Lass aber die Finger von den Dingern... sieht gut aus, ist aber bei schwereren KH, und dafür sind sie ja..., echt unangenehm in der Handinnenfläche. Hab die Dinger umgebaut, und nutze sie nur noch als Halter. Hab Zurrgurte und Ketten genommen, um sie zu sichern. Vlt. Mache ich dazu noch ein Video- ist echt einfach. Guten Pump
@@uncle_maik ach schade, vor allem das Umsetzen mit beladbaren Hanteln ist absolut bescheiden. Aber danke für deine Info. Bin auf weitere Homegym Videos gespannt.
@@hanswestmar3450hab sie als Aufhängung umfunktioniert. Dann ist es angenehmer. Vlt. Mache ich dazu auch noch ein Video vG
Dimensions plz
Bench height how much it is
hi the dimensions can be found at the very end of the video.
Where
Bench height how much
Привет ты гений
Thanx😀
Monstro!!!😀
Thanx😊
Излишества которые приводят к удорожанию конструкции и абсолютно не влияют на надежность и экономию времени при занятии спортом !
What do you mean by that?! The translation according to Google somehow makes no sense...😅
Good! But bad for any from a market $100! )) Think 110kg max too!)
hi, what does the sentence with the 100 euros mean? I weigh 115 kg, train with a 120 kg bench... so 235 kg is fine. how much maximum... no idea. have a great pump
Thanks, ire por ello.
Good luck, and a great pump😀
Ese es soldador o herrero refinado...jeje que trabaja sobre alfombra. Sin quemarla. Jajajaja felicidades una buena obra.. puedes publicar los planos
gracias gracias - corté las manchas cuando se quemó la alfombra🤣 no, bromas aparte... Ya no tengo los planos, pero puedes encontrarlos al final del vídeo. Atentamente
Hi, you find it at Minute 19.00.
Hallo, wie dick sind die Rohrwände? .
Hi, hab 3mm genommen. Ist perfekt. VG
@@uncle_maik ok, danke, gutes Video
Danke schön
Welche profile hastdu genommen? 120x120x3?😊
Hi, hab 80x80x4 genommen. Würde es aber jetzt eher mit 60x60x oder 70x70 machen. 80x80 ist schon dick... stärke mit 3mm wäre mir zu dünn, 4mm geben mehr Gewicht und Stabilität. Viel Erfolg.
hast du tipp wegen guten bohrern ? dein stufenbohrer scheint auch top zu sein.
Hi, hab alle Bohrer und auch den Stufenbohrer von Aldi oder Lidl. Bin mit der Qualität sehr zufrieden. Tausche die verbrauchten Bohrer einfach aus, bei dem Preis kaufe ich halt neue. VG
Сборка на ковре? Ты сделал мой день!😂
Главное удобно🤣 и всякий раз, когда горело, я останавливала камеру😂🤣 большой привет
I thought it was some kind of non-burning basalt carpet 😅
Yes😂😂
Is there any micro movement to the right or lift ?
hi, the movement is very slight. no more than with a studio bench. Best regards
Very nice work. I'm about to make one, I wonder how much material it costs?
Thanx. You cn buy ist online, there is it cheap.Good look.
@@uncle_maik really? What is the web?
It's a german Steel Shop. But I think, there ist only shipping to germany...
Молодец !!!
Thanx😊
😅Молодец !!!
😊
sir I watched a few DIY project videos which helped me a lot thank you for the videos good luck 💥 RESPECT SIR ❤🔥
Thank you very much and have fun and success with the reconstruction
What a great bench build, I was wondering if you could send me your plans, would like to build one
Hi, unfortunately I don't have a plan anymore. At the end of the video you will find the dimensions. good luck with the reconstruction
How much did it cost you in supplies
Echt gut gemacht!
Danke schön.
Excelente trabajo desde chile.. saludos.
Muchas gracias. saludos desde Alemania
Hi, ich finde es geil, dass hier mal einer DIY Videos macht mit Metall. Ich hole mir total viele Anregungen hier. Bitte mehr Videos! Geil finde ich auch das Mindset: Schieß drauf wie die Naht aussieht, funktionieren muss es!
Danke für dein Kompliment, außer für die Nähte😂 werden aber von Mal zu Mal besser😅 guck mal bei der Dip- Maschine... da bin ich schon ein wenig stolz😊 mit Ele ist das nicht so schön, bei der Safetysquatbar hatte ich die Gelegenheit, WIG zu schweißen- viel geiler... naja, hauptsache hält. Den Rest macht dann die Flex und der Lack. Guten Pump.
Ur coole Videos, mach ich auch so!! Mach weiter so!!
Danke schön. VG
The squares 11:55 that you have used can max load weight capacity of 150kg. How can we weld in a way to increase the max weight capacity to atleast 250kg if not 300kg
No risk no fun😂 i think, it is okay for more than 150 kg. But take bigger Steel-Plates.
@@uncle_maik haha okay sure.. Thank you
wo bestellst du deinen Stahl, wegen den Versandkosten?
Hi, bisher immer bei Stahlshop24.de ging schnell und ist günstig. Viel Spaß beim Nachbau. VG
Good job bro!
Thanks! Get a great Pump!
Excelente buen maestro.
😍
Does this setup mean double the distance and half the weight when pulling?
Hi, if you pull from the top, you have 1:1. But if you pull from the floor, you have half weight and half distance. Look at the cables- you see the difference between the way. If you want it also by pulling from the top, you need an extra role between the weights and the first cable. Greetings from Germany
@@uncle_maik Thanks for explaining, understood. Greetings from Sweden.
10x 4 sharing man
How long iron in 3.40 mnt?
hi, the tubes are all 60 x 60 mm, one is 60 x 30 mm. in minute 20.33 you will find all the measurements. just zoom. good luck.
What Angle was it used? For foot and head?
@@hadyblack9874hi, you can snap it in every 5 cm and thus set various angles between 0 and 90 degrees at the head and between 0 and about 30 degrees at the foot. hi, you can snap it in every 5 cm and thus set various angles between 0 and 90 degrees at the head and between 0 and about 30 degrees at the foot. Hallo, man kann es alle 5 cm einrasten lassen und so verschiedene Winkel zwischen 0 und 90 Grad am Kopf und zwischen 0 und ca. 30 Grad am Fuß einstellen. hi, you can snap it in every 5 cm and thus adjust various angles between 0 and 90 degrees at the head and between 0 and around 30 degrees at the foot. Hallo, man kann es alle 5 cm einrasten und so verschiedene Winkel zwischen 0 und 90 Grad am Kopf und zwischen 0 und etwa 30 Grad am Fuß einstellen. Best regards
Im making the bench, but me and my dad made it uneven 😅
how exactly? if it's not level, put something under the pad and frame to make it level. I'll keep my fingers crossed for you, let me know if it fits. greetings from germany. 💪💪💪
@@uncle_maik Thank you for your greetings and your advice, its actually cause the ground we made it on Is uneven so it became uneven with it 😅🤣
@@spiderbull274 OK. flex and re-weld 🤣 but first bring it into balance. good pump after welding💪
@@uncle_maik 🤣💪
Сварка на ковре, красота)
лучше ковер сломан, чем пол 🤣😂
Respekt! Kann man wirklich loben, wer solches Handwerk versteht! Chapeau! 🎩
Danke schön. Viele Grüße.
Ok
😀
Hola. Tenes medidas?
al final los encontrarás
👍👍👍
😀