Пікірлер

• 
  @PulkaSkurkenСағат бұрын

  12:54 NO it did NOT have Oxygen Sensor, we call it Air Mass Meter here in Sweden, but the E30 did not had one, the E34 and 36 had them. and broke often in the early year models, i changed two of them on two different cars. BUT i know American BMW cars could be very different motor wise compared to Europe, so a late E30 might had one. and specially if it was sold new in California?? just one example, a American E36 M3 was just a European 328 or 330 with the body looks of a M3.

• 
  @disturbingkreationz36 минут бұрын

  @@PulkaSkurken Yea I figured this but the car had a newer header pipe with a hole for 02 sensors so how do you know if it’s tuned or w e? This was first day walk around. I knew it wasn’t all stock.

• 
  @PulkaSkurkenСағат бұрын

  8:27 LOL, sorry for loling, but that was a bit funny tho. 😂 And you are better of with putting a new one in anyway :)

• 
  @disturbingkreationzpets40 минут бұрын

  Good advice

• 
  @PulkaSkurkenСағат бұрын

  7:30 That is a common issue on the E30, and it was common 20 years ago, powersteering leaking due to tube corrosion so the hoes dont seal it properly under pressure.

• 
  @disturbingkreationzpets39 минут бұрын

  I did not know that but the hose was rotten and I fixed it.

• 
  @PulkaSkurkenСағат бұрын

  5:39 LOL that bolt haven't had a nut for a LOONG time, iam pretty sure that lid have been solid on until thanks to old hardened dirty oil, until someone did run it warm. and the dirty oil seal was washed away with warm oil. you can drive as long you drive it like grandmother and not pushing the oil temp to slightly hot. but it has to be fixed asap!

• 
  @disturbingkreationzpets40 минут бұрын

  He wants a drift car and this car was someone’s “project” he bought.

• 
  @disturbingkreationz36 минут бұрын

  @@PulkaSkurken sorry I replied from my other account lol

• 
  @PulkaSkurkenСағат бұрын

  No as a old Swedish BMW owner (owned and drived BMW for 20 years, now i drive VW instead. new BMWs are fugly AF.), mostly E34 and E36, you DO NOT want remove the AC unit you will never be able to get it properly sealed if you dont have all the parts and tool that the BMW Serivce garages have. its better for the system to keep it in place and keep it sealed. will only give you problems later with corrosions and other stuff. also here in Europe those old is filled with gas that is illegal to refill outside a proper BMW Service garage or like a AGA Service depot. So to make you life easier and not buying a tone of spare parts for you 1980is AC, i recommend let it sit.

• 
  @disturbingkreationz34 минут бұрын

  @@PulkaSkurken first it’s not sealed at all. It’s also completely locked up on the pulley clutch so it should be removed. I do have equipment to catch the old R22 toxic gasses. It can be replaced with new AC unit and R134 gas non toxic. Thanks for all the comments.

• 
  @dallasjenkins947612 сағат бұрын

  What's that in the shop for? Like what the dudes plan?

• 
  @disturbingkreationz33 минут бұрын

  @@dallasjenkins9476 guy bought this car and wanted me to turn it into a drift car projects.

• 
  @mishkaconrad708912 сағат бұрын

  Becomes too much sometimes Conrad

• 
  @disturbingkreationz20 сағат бұрын

  I got this antique E30 in the shop and was so happy until it turned into a disaster.

• 
  @dallasjenkins9476Күн бұрын

  1

• 
  @disturbingkreationzКүн бұрын

  My God my first owned wrapped project. Tired of building cars for others. 😂

• 
  @DisturbingKreationzFirebladeКүн бұрын

  Show that motorcycle!

• 
  @geromelenord46752 күн бұрын

  Those little fins keep lifting up on me 🤦‍♂️😤

• 
  @disturbingkreationz2 күн бұрын

  @@geromelenord4675 yea I know! It’s a secret. Use a longer piece and heat it well to make the stretch over them. Immediately mold around the fins. I took the piece off the mirror to do it.

• 
  @DAN-lo5db2 күн бұрын

  I used it on my 2017 honda accord exl. It worked, but it took a lot of sanding passes

• 
  @disturbingkreationz2 күн бұрын

  @@DAN-lo5db thanks for the comment. I love doing headlights. I reviewed a few different products.

• 
  @disturbingkreationz3 күн бұрын

  These are 2 tips. People take stuff so serious. lol if you leave a criticism please link YOUR video of correction.

• 
  @Ochrelove3 күн бұрын

  Everyone’s main complaint I’ve heard is the tip breaking easily because of poor choice of material

• 
  @disturbingkreationz3 күн бұрын

  @@Ochrelove excellent observation. I had 1 do that and the other shorted out.

• 
  @TheDeadMan38484 күн бұрын

  4:07 l always use an old vodka bottle.

• 
  @disturbingkreationz4 күн бұрын

  @@TheDeadMan3848 cool. I funnel my distilled water into this FREE soda bottle to store.

• 
  @tonydavis78524 күн бұрын

  I need a transfer case off the back of a 722.9 2012 e350 4matic I’m most greatful for any help i know u have to get the whole trans but either way I need help

• 
  @disturbingkreationz4 күн бұрын

  @@tonydavis7852 what are you asking? How to get a 4 wheel drive case from a transmission?

• 
  @tonydavis78523 күн бұрын

  @@disturbingkreationz i need to find a used one I have had no luck any help I would appreciate

• 
  @Bionik19804 күн бұрын

  What year is the Audi?

• 
  @disturbingkreationz4 күн бұрын

  @@Bionik1980 this specific one I owned was a 2000. It is basically the same on most of their models.

• 
  @Greenhairchris5 күн бұрын

  Sooo stock smoke or amber

• 
  @disturbingkreationz5 күн бұрын

  @@Greenhairchris what are you talking about? lol the amber is stock. The white is LED. Then I tinted the new LED.

• 
  @enriqueb44126 күн бұрын

  Not any type of water. It has to be distilled water.

• 
  @disturbingkreationz6 күн бұрын

  @@enriqueb4412 I heard this too. I been a mechanic 22 years. I have used tap water in my mustang for 15 years with zero problems.

• 
  @enriquesalinas88586 күн бұрын

  I like your coolant thing. When i was parts sales i tried so hard to convince people to do this. Distilled water is like a dollar. The car could take eight gallons most people would rather buy the 50/50 anyway. Cray

• 
  @disturbingkreationz6 күн бұрын

  @@enriquesalinas8858 thank you for trying to help others. Appreciate that. Some people just love to be scammed. 🤣

• 
  @linuxguy11996 күн бұрын

  I personally buy the 50/50 because my time is valuable and I prefer to just add it in and not have to worry about the ratio, mixing, and all that BS. I know its more, but i only change it once a year, saving $2 per year is just not worth the extra inconvenience.

• 
  @disturbingkreationz6 күн бұрын

  @@linuxguy1199 great comment and a lot of people think this way. So pour in half a bottle and then 1/2 gallon water. I mean pretty quick and simple to me. Pour the entire gallon in a bucket and a gallon of water. Now you spend 30 whole seconds and spent 50% less money.

• 
  @nicholasyeti48516 күн бұрын

  For the second tip, it’s important to remember that you need to use at least distilled water, or even better, de-ionized water to mix your concentrate, you need to factor that into the cost to see if you are really saving money. If you put hose water into your coolant you can get hydrolysis reactions in your cooling channels which can corrode your cooling channels and poke holes in your heater core.

• 
  @disturbingkreationz6 күн бұрын

  @@nicholasyeti4851 I use filtered rain water. Or distilled water from my dehumidifier. Excellent comment though. Thanks.

• 
  @dallasjenkins94767 күн бұрын

  I didn't know this about coolant.

• 
  @mishkaconrad70897 күн бұрын

  Smart

• 
  @dallasjenkins94768 күн бұрын

  Sweet

• 
  @disturbingkreationz9 күн бұрын

  Check out our motorcycle page at @disturbingkreationzfireblade

• 
  @DisturbingKreationzFireblade9 күн бұрын

  Need subscribers

• 
  @mishkaconrad708911 күн бұрын

  Nice

• 
  @disturbingkreationz7 күн бұрын

  So nice

• 
  @dallasjenkins947611 күн бұрын

  How much was the lift?

• 
  @disturbingkreationz11 күн бұрын

  We got a lift and now we are ready to upgrade.

• 
  @TheMizarc112 күн бұрын

  have you ever removed the leather from a steering wheel? I'd like to swap the heating element from a 4 spoke over to 3 spoke. For whatever reason Audi didnt offer heater steering wheels on the three spokes around those model years.

• 
  @disturbingkreationz12 күн бұрын

  @@TheMizarc1 thanks for the question. no I have not. Seems like a lot of work. I would love to hear the outcome if you do it though.

• 
  @joelaizprua863715 күн бұрын

  Hello, where is localizated Map sensor in a Tuscon 2008 g4gc?

• 
  @disturbingkreationz15 күн бұрын

  @@joelaizprua8637 thanks for the question. Is it a 2.0 or 2.4? If not what engine do you have?

• 
  @twistedgalexy74717 күн бұрын

  1st I was hoping that you would show me how to use the damn thing cuz it was a gift I was hoping you would at least explain why and maybe exploded on you cuz I'm not worried about it but my table looked exactly like yours I had all three exact same tools

• 
  @disturbingkreationz17 күн бұрын

  @@twistedgalexy747 thanks for the comment. I was trying to prove this thing is a scam and never worked for anyone.

• 
  @Jesusisalmighty18 күн бұрын

  Sweet video

• 
  @disturbingkreationz18 күн бұрын

  Thanks!

• 
  @Disturbingkreationztvseries18 күн бұрын

  Get that car ready so we can wrap it.

• 
  @disturbingkreationz19 күн бұрын

  Just a quick bmw maintenance video for my viewers.

• 
  @mishkaconrad708918 күн бұрын

  Make more z4 vids comrade.

• 
  @dallasjenkins947619 күн бұрын

  Smart tips.

• 
  @disturbingkreationz18 күн бұрын

  Glad it was helpful!

• 
  @KacemHaddou23 күн бұрын

  Hello brother Can I Ask you a question pleas?

• 
  @disturbingkreationz23 күн бұрын

  @@KacemHaddou yes, what can I help you with?

• 
  @MrDontask00724 күн бұрын

  Do you think I could pop out the rivet without grinding down? Also - did you ever install the 911 bumper? Would ove to see it.

• 
  @disturbingkreationz24 күн бұрын

  @@MrDontask007 mine looked like I couldn’t see the center to punch out until I drilled it down and made it way easier. Second the auto trans had that “front pump bearing” problem from factory and wore out the area and leaks now so it is in the shop while I look for one. We do have 2 other boxsters we are building on this channel and our TV SERIES KZread channel. Subscribe to both and ask any questions we can help with.

• 
  @LoneWolfLifeStyle7225 күн бұрын

  That trans girl had a deeper voice than you

• 
  @disturbingkreationz25 күн бұрын

  @@LoneWolfLifeStyle72 lmao yup. Fired him 3 weeks later for being a pedo. I didn’t know and we try to give everyone a chance.

• 
  @johnpires358125 күн бұрын

  Thank you! The Audi manual showed a special tool to disconnect the brake pedal from the booster. This video was a tremendous help.

• 
  @disturbingkreationz25 күн бұрын

  @@johnpires3581 great comment! Any dealership will gladly sell you a “tool” to make money. I make videos in my shop for the common person to build confidence and save money. I hope we achieved your subscription and a like on the video.

• 
  @dallasjenkins947628 күн бұрын

  I love this car.

• 
  @LashLaRue-x9oАй бұрын

  My name is Meadow

• 
  @disturbingkreationzАй бұрын

  @@LashLaRue-x9o that’s awesome! I found her on the street it was called “meadow brook lane” so I named her Meadow!

• 
  @dallasjenkins9476Ай бұрын

  That shit hot.

• 
  @jerryhardesty9993Ай бұрын

  video sucks!!

• 
  @disturbingkreationzАй бұрын

  Lmao. Brah just because you have no mechanic skill and have to watch someone else doesnt mean you have to be mad at me because you feel inferior. lmao.

• 
  @chandlerisaksen5309Ай бұрын

  🔥🔥🔥Love this Wrap

• 
  @disturbingkreationzАй бұрын

  @@chandlerisaksen5309 thanks. Come help me wrap the z4 next month.

• 
  @mishkaconrad708929 күн бұрын

  Me too

• 
  @disturbingkreationzАй бұрын

  Had to take my girl to get groceries.

• 
  @user-pu7vc8pz1rАй бұрын

  Hi sir the accelerate of my car is not working at all so I need help to understand that what the cause of this plz help

• 
  @disturbingkreationzАй бұрын

  @@user-pu7vc8pz1r there is a sensor on the pedal. These cars are drive by wire which means if that sensor is bad it can’t tell you are using the pedal. Test that sensor. I show it in the video.

• 
  @ashlee896Ай бұрын

  What engine is it and how mutch does it cost to get fabricated and does it run good?

• 
  @disturbingkreationzАй бұрын

  @@ashlee896 that is called a hawk 250cc. It’s a replica of a Honda engine so it bolts right in and they are cheap. No fab needed or very very little.

• 
  @disturbingkreationzАй бұрын

  @@ashlee896 I just started a motorcycle channel called @disturbingkreationzfireblade. Check t out and sub. I’ll be doing bike work and dirt bike work there.

• 
  @ashlee896Ай бұрын

  @@disturbingkreationz I subscribed, Do you have a link to the motor I have been looking everywhere and cannot seem to find it?

• 
  @disturbingkreationzАй бұрын

  We started a new channel. We removed the motorcycle stuff from this channel and are addicting it weekly to the new motorcycle channel called DISTURBING KREATIONZ FIREBLADE