Welcome to my KZread channel where you might find from some casual home music recording, review videos to some run of the mill how-to tutorials and do-it-yourself ones. Hope you enjoy while you’re here.
I am CNC machinist by trade but found myself exploring a lot in other disciplines for instance information technology, computers related topics, 3d printing, FPV drone, robotics, electronic and most importantly video productions. Maybe it's just my own way to continuously gain knowledge what's around me.
Hope that these videos that I put a lot of effort into creating them serve you well during your visit to my channel. If you have any questions or comment about my channel content, please hit me up with the contact email link below.
Пікірлер
Mine arrived with Hex Screws
@@NoodlesNJ1 that's even better.. i hate philips head screws.
None of my touches register, I could hold the 5 fingers for multiple minutes and it won't pop up
it can only mean that your android head unit firmware doesn't support that function. what you can do is to use USB mouse connected to USB port of the AHU and go into setting parameter to find out its Touch Calibration setting. If this doesn't work, you just might have a dead touch screen which is hardware problem which usually can't easily be fixed.
What if the volume on your steering do not work? How do you fix that? Ive got an 07 honda accord.
does it work without the Android head unit? meaning does your steering buttons work before?
Wat is the reset code
there is no reset code. Just press the reset button top left labeled as RST
"hi5, namaste" nice video buddy:-*
Thank you man you are a life saver bought a radio and if I would touch left and would move right making me go crazy
@@TheRariza23 most likely due to installation we screwed up the touch calibration setting. Hope it helps man.
I had the same, bought a chain for me mountain bike and paid €10.- for it. Found out that it would shift back or just pull the whole chain off when back pedaling. It wouldn't shift properly no matter how long you tried to fine tune it, like gearing up would work but down not, and vice versa. The new chain I got on right now costed me €17.- but that one was bought from a bike shop. (decathlon) Everything runs fine, you don't even hear him going up or down while shifting. Next time I need a new chain I be buying the €23.-, especially with these things expensive buy is cheap buy. They last way longer and you ride is way smoother, I will never try to safe money ever again on things like this.
compare side-by-side!
My radio doesnt turn camera when I turn radio I have t900 with difrent setings and i cant find setting to make it turn on when I go to reverse I have wire attached to reverse bulb
Solved a mystery for me. I had lots of metal shavings when I lubed my chain. I definitely have a fake chain, could tell by the box (and price), but I was wondering what the downsides are. The metal shavings are probably from the chamfer that's supposed to be there. They're a key part of the HG-X system, designed to interface with the gears.
To be honest, i have not got any issue with the fake one except if i back pedal too much the chain would drop on me while the genuine one doesnt do that. Besides that, since i am only 140lbs so I havent experince cracked links or broken chain. It is just my own experience with the fake chain thinking i got a good deal on it. 😂😂 Honestly for my shitty bike and i dont care about wearing all other parts, i would order a chinese made brand chain instead of fake Shimano.
If you have a lot of shavings coming out from your chain, it means the roller pins are not heat treated right (surface hardness of roller pin). The effect is that your chain will get elongated and streched too much! With that said if the roller pins are heat treated too hard they become brittle and might break on you. So there is a fine balance between soft vs hard pin. And most cheap chain dont bother with hard pins. 😅
@@lavithhcm I don't think it's from the roller pins, but maybe you're right. Looks to me like the teeth are grinding on the chain. There was a nearly alarming amount of shavings. Some say it happens when shifting under load, which I do sometimes.
@@mortona42yt Shifting under load also depends on what kind of gearing you got, for example on a old mountain bike 3(front)x8(back). Shifting under load is forbidden, while if you got them city bikes with internal gear with for example 6/7/8 gears. You can shift under load just as fine as shifting while back pedaling... Even some new gears shifts better under load than without. What bike and what kind of shifting do you got? And are you sure it is not just one bad link? (if the chain gives while back pedaling at the same point, you do know.)
@@Desperado070 Kona cyclocross with 3x10 (I swapped from 2x). New cassette too, so it has to be this cheap chain?
Not to brag, but I guessed n°2, just by looking at the overall quality/"shinyness"(?) of the metal and the VIA marking.
No.2 is authentic genuine Shimano chain. Same with No.1
Front Rear option how to plug it behind? are you using 6pin? isnt that just for one camera?
Not sure if I understand your question but here it is.... The my front camera (inside the car) is connected thru my android head unit USB port. The rear backup camera (license plate) is connected thru special wire that is labeled "Reverse Camera" from the AHU pinout. If you have multiple cameras (front left, front right, left, right, rear left, rear right ) of course there is also the pinout label (in your case 6pin) to let you know how to connect them. When you have 6 cameras wired up and connected to that 6 pin, you can use 360 camera app. Since I use only 1 license plate camera, I don't use 360 camera app because it makes me confused what is left and what is right. Hope it helps!
@@lavithhcm oh, i see, you are using a USB camera.. The 360 is 12-pin I believe, the rear cam is 6-pin.. there is 6-pin for USB but I need to get a USB DAS front Cam.. SOrry I though you where using two cams one Front and one in the rear coz that is what I was trying to do..
Arent these camera not supposed to run in long periods? they get overheated or something? Thans why the 360 app closes too early sometimes
I can turn it on thru the app and leave it on for extended period and I have no issue with it overheating. My is just a dummy backup camera and it doesn't do any processing like file compression or anything like that (that's why it is cheap) The Android head unit camera app does the actual recording and save it in AHU memory. I don't use 360 app because I have only 1 backup camera. If you have many cameras install around the car, 360 camera app makes sense.!
@@lavithhcm I have on car has 360, but another im trying to install Rear&Front(not sure how to wire it-prolly DPDT 6-pin on-off-on toggle).. I havent looked into it that much yet but it seems there is no settings option for the 360/Rear cam app to stay on while driving..
I have the same version that you do and mine does not change colors
Buy metal upgrades that is the best thing to do. My car is a little heavier which is good sticks to road. A lot stronger 💪 no more having to buy plastic broken parts no more !
Only certain metal parts i would buy. But for the arm, i would rather stick with plastic. Metal parts have too much play in them thus making the car acting weird. You can always shim it though. I did buy some metal parts for this RC car/truck.
I did everything you showed. It just stays white :(
Some models just don't come with RGB leds at those so you cannot change it. It's hardware limitation so not much you can do. Best of luck! When i first reset my unit, those soft buttons cycle thru various colors so i know my unit has RGB leds.
How did you get your panel keys the change color?
kzread.info/dash/bejne/eI57q6qChJvaips.htmlsi=ERxksZtBxrjzzA39
Perfect this is the video I really needed to see, as I have just got this rc buggy and on first day very first go a have done something to back drive, they are making a bit of a grinding noise and not good traction but still 4 wheels spin off floor but on floor back wheels very little traction. A think a have stripped a gear that go's into diff from drive shaft. A have body off just needed to strip rest down in have look. Am going to upgrade to all metal diff and gears wile am at it. May as well since am stripping car down. Hope I put all the difference size screws in right place 😂. Wish me luck. 😅
So did you strip the gear.? I doubt it though. I have broken the wheel axial using 3s battery runing in water but never stripped the gear. 😆 i find it best using marine grease with this cheap rc. If you use fluid, make sure it's sealed otherwise the fluid is just spun off the diff. Too thick fluid is not good either. Anyways, tube of marine grease will last long time. Best of luck!
I just got this in mail today and it's ment to be v2 the control is a v2 and first go I got it stuck in long grass and tryed to get it out and back wheels are not spinning like front wheel now 😢 what have I done do you think stripped the cogs in the back diff???
Hello, I have tried to fix the radio with this method, but it didn't work for me either, do you have another solution or it simply doesn't work or fix anymore.
What you can do is to use USB mouse connected to android head unit. Use the mouse to go into setting menu and find touch calibration setting in there. Best of luck!
I followed the steps in this video to attempt to connect voice connect and it doesn't work. I used to be able to press a control button on my steering wheel to initiate a phone call, but can't with this system. It's really frustrating. I have Podofo Voice and am having issues getting that to function properly. My unit is Podofo 9212B. The manual that came with it is very unhelpful so any help you can provide is appreciated! Also, I use iPhone and prefer to use a different map app for navigation. Can apps that didn't come with the unit be downloaded?
I'm also from Canada. Did you have to pay duty and import taxes when buying from Formbot?
i think i did pay for the shipping company like 45CAD for duty. Anyways if you decided to buy it, you can purchase thru this link. www.formbot3d.com/products/voron-24-r2-pro-corexy-3d-printer-kit-with-m8p-cb1-board-and-canbus-wiring-system?DIST=Rk9OHVk%3D&VariantsId=10457 Really appreciated! Thanks
Did that but still didn't work😢
Your touch hardware is bad? Meaning your touch screen is screwed up! Anyways, another method is try to use PC usb mouse to access touch calibration menu and from there you can recalibrate your touch screen. If that doesnt work. I dont know what else. Best if luck! 🥰
anh ơi làm thêm video về PID nữa đi a . a giải thích TPA và cách tune TPA đc k a
Lâu ngày ko có chơi quad, nên chắc cũng lú về quad rồi. 😁😁😁
Thank you for showing us are to turn on the backlight. Sadly it only stays white but that’s not the issue. The issue is why wasn’t this program as a default to have the backlights on for those buttons and not have to mess around with the factory settings just to find? I have to do something similar the other day to figure out why it would mute my music whenever I go reverse the car. I’m still new to this radio learning all the things I can do with it.
Yeah after using this unit for over 2 years and i have not noticed it would mute my music when reverse. 🤣
Hello, please can do you a video on how to remove the car and change what you see on the home screen?
sure.... it's a car launcher app that you need to download from Google Play Store. You can either use "free" or "paid." I am using the paid version of CarWebGuru. kzread.info/dash/bejne/rGx3s7yRcbWWhbw.htmlsi=9BAMMCqi03iMGzTE
Very details instructions how to open this wltoys rc car. Thank you! U dman ❤
Very good man 👍 This video helped me to set both key1 and key2, at first only one key wire worked for me. Thank you so much 😊
Glad it helped. Cheers
Oh man, Thank You From Indonesia.
The bottom of my screen is not working when I push it but it not crack or anything.. so if I try to go in the Android setting I can’t click the ok button.. any idea what it can be?!?? Thanks for your help and great videos bro 💪🏼
did you try this to calibrate your touch setting? kzread.info/dash/bejne/m2d8w5KIeNS0ec4.htmlsi=_X2QdK9jdAwCc_At
I just ordered one on AliExpress, $80 usd right now on sale with the $12 off 89 or more lol insane deal
yeah get a 3S battery for it and it flies. 🙂
gotta see this clip too kzread.info/dash/bejne/ipipk8esn9S8gMY.htmlsi=Ne5_xroy4b8TcF8n I ran 3S in it and snap the dogbone. :-) It does fly on water. LoL
@@lavithhcm gonna be the first rc car I've had since I was a kid, I'm pretty hyped. This one seems like the best cheap sorta hobby level RC
@@BoggedBogdanoff you will break something. That I know for sure! So replacement parts are a must.
Have you worked out how to remove the annoying Ferrari car in the centre of Home Screen ? I have the same and don’t know how to
kzread.info/dash/bejne/rGx3s7yRcbWWhbw.htmlsi=wIKRxYY5mcSMflZ0
I received mine today, tought it was a great deal, dude. Its painfull
You mean like it's hard to install it into your car. Yeah, me too it took me 2 days to figure out why the android screen wouldnt sit flush to the housing. I had to grind off some plastic material for it to fit. Be patient when installing it. Take care of the RCA connectors and use some sort of clamps (ziptie works too) to hold those connectors in place. When u leave them loose, there might be static noise down the road. Let me know if u need any help regarding the unit. Cheers
R u Vietnamese
Yes!
Best thing you can do is throw out the moons motors and put ldo super powers on then 48v it's a completely different printer.
Hahaha... yes yes I wish.
Thus the problem with selling pre-assembled cars these days. When you had to build them you knew everything about them.
A radio without antena?
Yup... no connector to connect antenna.
I did my five fingers on the screen but I don’t get result that you showing
Yeah maybe your android unit firmware does not support that feature. Can you somehow go into setting menu and search for touch calibration?
I can’t turn off the lights😢
tunggu sekitar 30 detik, akan mati
Oh thanks dude. This helped me too well.
You are welcome. Hope it helps.
I do not really understand why you need Z homing and Auto Z? For my I do a XY Homing and than I take the klicky probe and go directly to my bed for gantry leveling. I do not touch the z-endstop.
does your talk button on the steering wheel work? somehow, mine doesn't. i have a 2012 civic
I dont know cuz my car doesnt have talk button. I talk directly to android head unit which process my incoming phone call thru bluetooth. The android head unit listen to the wake-up word "hey google" and from there i can pretty much interact with it like giving a command "make a phone cal to...." "play music on spotify"... not sure if these function you are looking for.
If you mean the oem function of your civic talk button not working, then check if you have assign it to something else.
Thank you !! I now can use the buttons again 👍
I have that one for my New E-Scooter setup Speed Time and total KM as soon as it has contact with the SAT all works perfect Good Buy
Do you know how I can change the one thats part of the trunk? That one recently burned out on my RDX for the same model year.
I am not sure what part of the trunk? The light? You just need to pry the plastic cover off.
Is there a way to modify/reset the settings so that the guidelines for backing uo would show? You know these lines thatshow you where your car is positioned when your back uo your car? Thanks!
Up*
Sometimes mine shows uo out of the blue and sometimes it doesnt at all... i think its a software glitch that is hard to track down the reason why. Anyways best of luck on your finding because i gave up and accept its fate. 😅
On the side note, it must be within the included 360° camera app. You might find some setting there.
the CAN termination should be on sb2040 or the IDM?
you can choose which ever device to terminate on. IDM scanner is ok too. Just remember turn off the R120 ohm resistor on SB2040. If you terminate on SB2040 you need to make sure the 120 ohm resistor is remove from the IDM scanner.... The latter is complicated since the resistor is so small to remove on the IDM scanner. So it is advisable to terminate on the IDM scanner and turn off 120 ohm resistor on SB2040. Hope it helps!
Can you reach this from settings instead of putting 5 fingers on the screen?
Yes. There is a menu in parameter setting page which is something called touch calibration.
@@lavithhcm yes i found it. Thanks
Hi I have same radio in my audi a3 8p and also dont working stearlig wheel comands Where i can find the pasword?
Thank you!