Пікірлер

• 
  @comlbbeau20 сағат бұрын

  I just turned 700 trouble-free hours on my MX4700DT gear drive purchased new in 2012. Couldn't ask for more in a tractor of that size.

• 
  @weightbuilddig16620 сағат бұрын

  @@comlbbeau yeah it is a good tractor. I use this one mostly for bush hogging.

• 
  @fredc458411 күн бұрын

  Auto Parts store has an engine degreaser and then just pressure wash after spraying it on and letting it set for 5 minutes

• 
  @samb466813 күн бұрын

  I'm looking at something like that.. it's a 2017 cat 303.5 with a thumb, also come with a 24inch tooth bucket.. has 3,100 hours on it and they want 35,000 for it what do you think?

• 
  @weightbuilddig16613 күн бұрын

  With a cab? It really depends on the wear the machine is showing. There could be a machine with a 1000 hours and be wore out. So really you need to get on and operate it for a god 30 minutes and see how it does and look at if after you run it. Look for leaks or wierd sounds stuff like that. Make sure there is no slip in the bushings and pin.

• 
  @samb466813 күн бұрын

  @weightbuilddig166 yes it does have a fully enclosed cab.. I'll definitely look out for that stuff!

• 
  @bigal2593814 күн бұрын

  How much did the concrete cost?

• 
  @ChanceDeTexas18 күн бұрын

  Good job bro!

• 
  @yogendrapatil799422 күн бұрын

  great job! I have a cat excavator 308 which has a kill switch inbuilt and it really is a savior. I have a question, at the positive terminal there are 2 wires connected and the smaller wire is a little lose and when its moved the excavator stops completely. what is that second smaller wire and how can i fix it? Thanks a bunch

• 
  @weightbuilddig16622 күн бұрын

  Do you have a picture of it? It won’t tighten up?

• 
  @terrywix684425 күн бұрын

  Looks like the brother-in-law screwed the sister and the brother...

• 
  @Jerry-qj3kk26 күн бұрын

  Only $2800 bc of the concrete base.

• 
  @rrodriguez437829 күн бұрын

  Might be a dumb question, but do you get the same MPG? I just got mine today. They are kind of heavy. Thanks

• 
  @weightbuilddig16629 күн бұрын

  Yes I got the same gas mileage.

• 
  @rrodriguez437829 күн бұрын

  @@weightbuilddig166 thanks for response and help installing

• 
  @mikeyiceeeАй бұрын

  Buddy can’t dig straight lmao only 3.5 ft swap and 50ft run …. What a bum

• 
  @mastercreamer1398Ай бұрын

  Sheet it on the ground, no need for plumb and line.

• 
  @mastercreamer1398Ай бұрын

  As a contractor who builds nothing but sheds and garages with a framing, concrete, and roofing background, this was hard to watch.

• 
  @michalwalenciak247827 күн бұрын

  Make better video. Show how it's done, contractor who builds nothing but sheds and garages 😂😂😂😂

• 
  @ceciliosoto526Ай бұрын

  Does this build require building permit?

• 
  @weightbuilddig166Ай бұрын

  It did not. I’m sure that has to do with I don’t live in the city limits. It did require a permit when I built my house.

• 
  @user-hm4ms2uk4mАй бұрын

  Did you sell the Big blue 2012 Ram 3500?

• 
  @weightbuilddig166Ай бұрын

  Yes I did.

• 
  @gratefultedd969Ай бұрын

  Did tou leave room for the drywall to slide past the sides of the treads and risers? Because if not the dry wall guy or you are gonna be pissed.

• 
  @weightbuilddig166Ай бұрын

  Yes I did. I just didn’t have time to show it.

• 
  @HBSuccessАй бұрын

  IRC max riser is 7.75”, and that’s steep enough. 8” for a main stair would fail inspection here. Also not rounding over the noses before you set the treads is a huge mistake 😵‍💫

• 
  @weightbuilddig166Ай бұрын

  8” is the max here. The treads i used were really the subfloor for the stairs. I put on nice oak bull nose treads when finishing the floors out.

• 
  @scrambler69-xk3kvАй бұрын

  I made the mistake of buying a front wheel drive lawnmower and it will not happen again. If you are buying because of slopes, then do yourself a favor and be sure you buy a rear wheel drive mower. They do not work like cars do. The rwd models have so much better traction. I do not know if there is more weight on the rear wheels or not but they go so much better. Lesson learned for me.

• 
  @weightbuilddig166Ай бұрын

  Thanks for your comment. I notice that with mine. The wheels are turning but there not really pulling you around, they help. Anyway I’ll keep that in mind.

• 
  @WilliamHollinger2019Ай бұрын

  Well now under Biden we have to pay $10,000 for a small shed.

• 
  @TRUMPSprisonSOAPАй бұрын

  Blame china

• 
  @tooolboxxАй бұрын

  What did the pad cost you?

• 
  @weightbuilddig166Ай бұрын

  For concrete and the dirt I had brought in total was $900.

• 
  @user-zg7qz9ph6xАй бұрын

  What does the diamond shape exclamation mark mean

• 
  @weightbuilddig166Ай бұрын

  For my machine it means something isn’t right. When it’s cold it on until the machine warms up. But if it comes on during normal operation then there is something wrong with the machine.

• 
  @user-zg7qz9ph6xАй бұрын

  @weightbuilddig166 thanks for replying. I will have to put a scanner on it.

• 
  @weightbuilddig166Ай бұрын

  What’s your machine doing?

• 
  @user-zg7qz9ph6xАй бұрын

  @weightbuilddig166 I found it. Left joystick needs linkage tightened and lubed. It started raining as I was backing off trailer. It was muddy and slick so I was creeping it back. As it tilted onto the ramps I looked forward to line it up if it were to slide and I saw the symbol go off a few seconds then realized when I go in reverse enough that it starts grabbing, the light stayed off. So when I get time to look into it I will let yall know what was up. Thank you and I will like and subscribe.

• 
  @daviddonley4874Ай бұрын

  Very Nice!!

• 
  @weightbuilddig166Ай бұрын

  Thanks!

• 
  @Janet-vs6xwАй бұрын

  WHY DONT SHOW THE FOUNDATION BUILDED !?

• 
  @weightbuilddig166Ай бұрын

  I did in the video before this one. To see the whole thing from start to finish is like 7 videos.

• 
  @tomathiasbeauford3759Ай бұрын

  🎉You still going in

• 
  @user-wz2qz5nn6zАй бұрын

  Planning on getting one next spring, had my current one for 10 yrs. It’s old and has starting problems

• 
  @john-ic5pz2 ай бұрын

  aw no ... he's for WBDs invaaaaaaaaade!!!!

• 
  @whaleshark26252 ай бұрын

  Is this anchored into the slab?

• 
  @weightbuilddig1662 ай бұрын

  I did put anchor bolts in after I had the walls up.

• 
  @georgeandlek2 ай бұрын

  That dirt!!!! Not a root, not a rock....like jelly....I'm overcome with jealousy, damn fine job...very neat!

• 
  @weightbuilddig1662 ай бұрын

  Thanks! We do have some good dirt

• 
  @skidmarkx86422 ай бұрын

  What was the cost of the slab?

• 
  @queenqutie9236Ай бұрын

  His anal virginity

• 
  @FR-VIDZ2 ай бұрын

  What rotos and breaks did you end up getting

• 
  @weightbuilddig1662 ай бұрын

  I don’t remember what they where. Just what ORielys had. They were a good match to what came off though.

• 
  @derekgemzala58862 ай бұрын

  Hey young boy, what kind of language you speck ?

• 
  @weightbuilddig1662 ай бұрын

  I speak fast

• 
  @brianc90662 ай бұрын

  So nice

• 
  @cgilleybsw2 ай бұрын

  So this has to happen for me this year. I see a lot of videos really pushing screws rather than compressor driven nail guns. Thoughts? For sure the screws are a little more expensive but no compressor, etc.

• 
  @weightbuilddig1662 ай бұрын

  Yeah I like screws for somethings. I used them to install my ridge beam. Then again on the rafters just one in each to get them in place. Other then that I like using nails. If you don’t have a compressor you could buy the pasaload cordless framing nailer! You don’t need a compressor. It comes with a battery and charger for $399. Here in Alabama! Then you buy the gas fuel cell and your ready to go. I told myself that when I build again I’m going to buy one. I don’t have to wait for the compressor to recharge, or deal with the hose being tangled or not long enough. So anyway that my thoughts. Good luck with your build! What size building do you plan to build?

• 
  @rigosalinas89152 ай бұрын

  Which gun and nails you use?

• 
  @musiholictara2 ай бұрын

  I came here looking for instructions so I could learn. I'm not learning anything.

• 
  @mflow30302 ай бұрын

  Just picked one up today. Currently $299 at Lowe’s. Mowers over the past couple of years have skyrocketed in price !

• 
  @weightbuilddig1662 ай бұрын

  I know! I thought the same thing! How do you like it?

• 
  @mflow30302 ай бұрын

  @@weightbuilddig166 I’m a big fan of these MTD build mowers. The deck does well and mulching and bagging. It’s lightweight and parts are everywhere. I purchased it to put it in storage until my other two break.

• 
  @rorysuire61772 ай бұрын

  Dayummmm....I'm seeing em online for 399...I guess the price went up. 🤦‍♂️🤦‍♂️

• 
  @mflow30302 ай бұрын

  @@rorysuire6177 they did. I see they’re $399 now. It was just a week long sale at Lowe’s.

• 
  @mondavou94082 ай бұрын

  I missed that sale! It ended 4/8 (i think), I was busy with the Eclipse. Now they're on "sale" again but $399.

• 
  @OptimisticMountainRailwa-yt8ve2 ай бұрын

  Watch it when you get home

• 
  @jmartinez5622 ай бұрын

  Solid job, he put shear wall.... Smart...... He also is making the top boards 2x6 for extra strength.... SMART!

• 
  @WaynesAdventure2 ай бұрын

  You got er done 👍 Nice trailer for your machine

• 
  @nicfeen77893 ай бұрын

  12” long and 16” high ?

• 
  @weightbuilddig1663 ай бұрын

  12 feet wide 16 feet long 9 feet wall height

• 
  @sammyjimsmith61003 ай бұрын

  You'r a fast worker, and 2800. bucks, unbelievable. Good video.

• 
  @helamanwayman58023 ай бұрын

  Does it have Bluetooth and if so how do you pair to your phone?

• 
  @weightbuilddig1663 ай бұрын

  Yes it does have Bluetooth. You turn on your Bluetooth on your phone and look for the radio and then hit pair. That’s how it worked for my iphone.

• 
  @Chainsaw_18.3 ай бұрын

  One of the Best trucks on the road !!

• 
  @thejoshthat3 ай бұрын

  I'm thinking about doing a 16x24 shop/shed on gravel pad with treated skids. I plan to just scale up your build to those dimensions. Thank you so much for the inspiration!

• 
  @grant12bowlingАй бұрын

  You could do gavel pad with concrete cinderblocks on the four corners and half way down the 24’ wall. That’s what I’m doing so I can park in it without having skids or plywood underneath the vehicle

• 
  @thejoshthat3 ай бұрын

  Note to self: cellulose pvc for bottom 12" of sheathing + soffits & trim. Also, "sheet clips" to seperate osb

• 
  @thejoshthat3 ай бұрын

  On the roof, is that 2x8s for the ends and 2x6s for everything in between? I like your way of doing the overhang, much more reliable than the ladder method. Thank you, looks great!

• 
  @weightbuilddig1663 ай бұрын

  Thanks! I used 2x6 for the rafters. And 2x4 on the ends

• 
  @lebu30443 ай бұрын

  Are those 35s?

• 
  @jacobkelly15023 ай бұрын

  Looks great love the Ozzy @11:30

• 
  @sickpuppy13693 ай бұрын

  Thank you for posting this video. Just bought a set of these exact ones and I'm waiting for delivery.

• 
  @weightbuilddig1663 ай бұрын

  Oh cool! Yeah I really like them. Super easy to put on, and they look good!

• 
  @johnbailey60223 ай бұрын

  I hope you have better luck with your package than I did. Just got my running boards yesterday and find that all 6 brackets are missing with numerous nuts and bolts missing. But hey; they threw in a bag of misc nuts and bolts that don’t even go with the running boards. And their customer service is a pathetic joke. Emails are a joke as well. So trying to get my mounting brackets may never happen. Do business with American made products.

• 
  @morganoverstreet68243 ай бұрын

  Does the radiator have to be drained to replace the thermostat?

• 
  @weightbuilddig1663 ай бұрын

  Yes

• 
  @DomoLadii3 ай бұрын

  😅 love your content and videos! Also Cat got ur tounge?? 😂

• 
  @weightbuilddig1663 ай бұрын

  Thanks! What you talking about? Cat got my tongue?

• 
  @DomoLadii3 ай бұрын

  @@weightbuilddig166 in the beginning of the video you kept crossing ur words 😁 hehe and kept mixing up your words 😅

• 
  @weightbuilddig1663 ай бұрын

  Lol gotcha.

• 
  @DomoLadii3 ай бұрын

  @@weightbuilddig166 😊🙏🏼