Пікірлер

• 
  @Nikolaih3119 күн бұрын

  Good afternoon! Tell me the timing tags 🙏

• 
  @IvanSoto-om8fk26 күн бұрын

  Will it remove my check engine light I have code 1127 which is over or under boost

• 
  @aftermarketassassins549125 күн бұрын

  Our tuning will desensitize the 1127 codes, but if there is a true issue with the vehicle, it will still set the code as this is a major safety factor for your RZR. This is a good read: aftermarketassassins.com/tech-blog/f/rzr-xp-turbo-boost-overboost-low-boost-waste-gate-adjustments

• 
  @shaneward40652 ай бұрын

  great tutorial

• 
  @jabroni61992 ай бұрын

  Stock Turbo R vs Tuned Turbo R and stock Pro R vs tuned Pro R would be quite a bit more valuable. This comparison doesn't actually tell us what the tune did.

• 
  @RokellKneller2 ай бұрын

  In full wheel drive to! 😮

• 
  @michaelybarra86743 ай бұрын

  I had a shop install your kit but they did not do the spring no in 1st gear on take off the rpms go real high before it fells like the belt grabs could this be why?

• 
  @aftermarketassassins54913 ай бұрын

  No, this would not cause high engagement of the clutch. The OEM spring should engage as low as ours. Make sure the clutch is assembled correctly and that the weights are moving freely on the pins. As per our instructions, a small dab of high temp grease should be used on the weight ID where the pin goes into. Thanks!

• 
  @twe73jr3 ай бұрын

  Anything for the 2023 570 sp Polaris yet?

• 
  @albertoarmendariz67994 ай бұрын

  I bought a 205 up kit for my Canam x3 turbo it came with a custom tuner but I want to go to e-85 is there a way to download the tune to the map tuner without buying another tune

• 
  @aftermarketassassins54914 ай бұрын

  Hi. The E85 tune is a separate tune we have to build, so it would need to be purchased. You will also need our 1200cc injectors. If going this route, the current tune you have will not run on the 1200cc injectors, so most purchase the level 3 (205hp, 91-93 octane) and level 5 (E85) for the 1200cc injectors. See here: aftermarketassassins.com/products/ols/products/aa-custom-tunes-pvcx-for-canam-x3-120hp Thanks!

• 
  @bigsmoothhh24 ай бұрын

  If I get this tuner plus a launch control module, which needs to come first in setting it up? Tune it then set up LC?

• 
  @aftermarketassassins54914 ай бұрын

  You would need the tune to run launch control or you would go into misfire protection. So flash first, then install the LC. Thanks!

• 
  @bigsmoothhh24 ай бұрын

  @@aftermarketassassins5491 Thank you! And a stage 3 tune for a Turbo R will do fine right?

• 
  @aftermarketassassins54914 ай бұрын

  @@bigsmoothhh2 Yep, they rip on level 3! We do suggest clutching, blow off valve, and exhaust for that level.

• 
  @bigsmoothhh24 ай бұрын

  @@aftermarketassassins5491 Sounds good, I have an RPM blow off valve, RPM J-tubes, intake, charge tubes, and a RPM cut out exhaust but no clutching so I will add that to the list

• 
  @thricecompany5 ай бұрын

  I bought my 2020 XP pro used with a tuner on it. I'm installing this kit tomorrow. How do I know what stage tune is on the RzR?

• 
  @aftermarketassassins54915 ай бұрын

  With the tuner plugged in (to a computer or the RZR with the key on), go to Flash Tune and this will show all available tunes that are compatible with your ECU. If they are our tunes, they will begin with either LEV or L followed by a number. This is your tune level. EX: LEV1 or L1 would be a Level 1 tune, LEV2 or L2 would be a Level 2 tune, etc.

• 
  @thricecompany5 ай бұрын

  @@aftermarketassassins5491 thank you. They were through dyno tune

• 
  @thricecompany4 ай бұрын

  I meant Dyno Jet tunes.

• 
  @thricecompany4 ай бұрын

  Also any videos or tips on how to change the primary spring and weights without removal?

• 
  @richardrawlings1816 ай бұрын

  Pretty sure its not an 1/8 inch allen. Its a 3

• 
  @courtdoubleday29226 ай бұрын

  P r o m o S M

• 
  @upsman1057 ай бұрын

  Nice video, thanks.

• 
  @william735517 ай бұрын

  Is there a way to make you fourweeler chop while idling and rev to about 1500 rpm when u crank?

• 
  @showtimespeedshop7 ай бұрын

  DONT USE GREASE….use a hotdog bun or any other bread. Way less messy. Crumble it up and pack it in

• 
  @RaulGonzalez-fu1yb8 ай бұрын

  I can’t tell if this is for the Ranger 1000 or 1000 XP. It looks like a regular 1000 based on the muffler location (XP has it on the side). Please clarify. Your website only has this product available for XP.

• 
  @aftermarketassassins54918 ай бұрын

  Hey! This is for the Ranger 1000 dual cam. It will not fit the single cam model as the mounting is just slightly different.

• 
  @apellerito310 ай бұрын

  ZOOM OUT FFS

• 
  @jbroughton200311 ай бұрын

  You're video suck because you are too close. Can't see the whole vehicle.

• 
  @waylonolsen11 ай бұрын

  I have your clutching on the way ... when is the tune and exhaust going to be ready for the Xpedition!! 😁

• 
  @aftermarketassassins549111 ай бұрын

  Tune has been listed online for a week or better now. See here: aftermarketassassins.com/products/ols/products/2024-polaris-xpedition-aa-ecu-flash Been busy but I'll get on some videos soon. Exhaust will be a little while out, but we are working on it!

• 
  @waylonolsen11 ай бұрын

  It's been a month Where's the new videos 📹 🤔 🎉😂

• 
  @SuperCorksoaker11 ай бұрын

  Do you have a video of the port where hook this up?

• 
  @aftermarketassassins549111 ай бұрын

  What model vehicle do you have?

• 
  @SuperCorksoaker11 ай бұрын

  @@aftermarketassassins5491 2022 Turbo R

• 
  @raptordan6851 Жыл бұрын

  It’s cool but it’s also $65000 (Canadian) for the loaded up version.

• 
  @dandilauro1334 Жыл бұрын

  Can someone please help. I had the s3 clutch kit and upgraded to the aa hd primary. After installing new primary something is terribly wrong. Almost seems like somethings locked up, primary spinning at idle and terrible grinding noise

• 
  @aftermarketassassins5491 Жыл бұрын

  Did you remove the inner baffle as per the instructions? This is the black plastic piece bolted into the inner(aluminum) clutch cover.

• 
  @patd4u2 Жыл бұрын

  are you sure the comfort, standard, sport toggle switch is for throttle? I think it's for the suspension. It does not have dynamic suspension like the pro XP's but I think that toggle switch is for changing the three positions of the fox shocks so you don't have to get out and manually change it.

• 
  @andyjones5602 Жыл бұрын

  There's many videos saying it throttle sensitivity

• 
  @patd4u2 Жыл бұрын

  @@andyjones5602 thank you, I would've bet some money that it was for the suspension,

• 
  @nwags35711 ай бұрын

  Switch is not for suspension at all. It’s purely throttle . These have FOX QS3 shocks. 3 meaning you have 3 click pistons on the Shock you manual handle just the same as the many years these FOx Qs3 shocks have had on the market. They did change the shock internals on this particular design.

• 
  @mingomane1 Жыл бұрын

  I sat in one of these the other day and the fit and finish is the best Polaris has ever done.

• 
  @mikegunn315211 ай бұрын

  Why doesn't anyone talk about the noise. How quiet or noisy are they inside and out. 🤷‍♂️

• 
  @mingomane111 ай бұрын

  @@mikegunn3152 very true. That’s the main reason I never went with a rmax. Those things are too loud. I had a krx and it was too loud for me and my 3 year old to talk. The Facebook groups are saying it’s pretty loud. Around 96 db when cruising

• 
  @aftermarketassassins54915 ай бұрын

  Unfortunately they are very noisy inside the cab. Check out our tech article for some of the fixes/suggestions we have for reducing in-cab noise: aftermarketassassins.com/tech-blog/f/polaris-xpedition-noise-reduction-common-issues

• 
  @user-fl6fd8ph5r Жыл бұрын

  Is it good for 2010 RZR 800s

• 
  @aftermarketassassins5491 Жыл бұрын

  Sorry it will not work with your year/model.

• 
  @DannyluxMx Жыл бұрын

  How high it can go the oem

• 
  @aftermarketassassins5491 Жыл бұрын

  10-12psi is about as far as we like to go as the throw is also being shortened.

• 
  @RicardoTorres-dy3yx Жыл бұрын

  Thx for this tips👍

• 
  @user-wb9ig4mc9o Жыл бұрын

  I have a question about the magnets, In the video the installer clearly says the weight pockets nearest the tip will be the fullest, Yet every weight profile on my install sheet has more weight nearest the pin NOT the tip as indicated. I'm running 37In dirt tires so I purchased the S3 Kit with the 1072 Helix W/ almond spring. With a stock tune it says 4/2/1 so 4 magnets nearest the pin and only 1 towards the tip. Am i missing something? Lastly as a note in my instructions it says if im running a heavier tire it "might require less weight" that's fairly generic meaning if I know im running a heavy tire (System 3 370s in 37in) should i remove the one tip weight or maybe one of the 4 weights nearest the pin? I hope these are not considered dumb questions I just want to make sure I install the kit correctly the first time. Thanks in advance for your feedback.

• 
  @aftermarketassassins5491 Жыл бұрын

  Good questions for sure! Go off of your sheet. Within the newest setups on the Pro R model, we found heel weight to work best. For your tires, I would suggest removing 1 magnet from the hole position 1(heel). That should work great and always make sure to check peak RPM. Thanks!

• 
  @user-wb9ig4mc9o Жыл бұрын

  @@aftermarketassassins5491 Thanks for the quick reply awesome customer service!!!

• 
  @toddteeters9031 Жыл бұрын

  Great company, and great service/dial in assistance. We were a bit off, but with AA assistance, we are right where we should be.

• 
  @francisdebelo Жыл бұрын

  Looks like it rips but I’m passing on any kit that puts parts in the bed. If larue can do it so can everyone else

• 
  @aftermarketassassins5491 Жыл бұрын

  The bed is fully usable and installed in our kit. See here: aftermarketassassins.com/products/ols/products/aa-pro-r-4-cylinder-turbo-kit Thanks!

• 
  @austinr09 Жыл бұрын

  Is it pretty normal for the inner primary sheeve to come off also? Mine comes off without a puller.

• 
  @aftermarketassassins5491 Жыл бұрын

  that is not normal, no. This is a taper fit and should be very tight.... needing the puller to pop it off with good force from an impact gun.

• 
  @lalo_etz Жыл бұрын

  i broke the peg🙄 any advice ? weld ? screw and nut?

• 
  @aftermarketassassins5491 Жыл бұрын

  No good! We've not had this happen, so no direct experience.... but in other applications we use a shoulder bolt. Welding an new peg on would also work... if you can get to the back side.

• 
  @DigRigPowersport Жыл бұрын

  terrible camera guy

• 
  @user-vw6nh2cl9p Жыл бұрын

  What’s the Can am weight with number 655 on it weigh?

• 
  @user-vw6nh2cl9p Жыл бұрын

  How does the clutch work right with different design weights?if three have sharper angle than the other three. ?also the hexagon rollers the weights sit on at idle why aren’t they round?

• 
  @BarrySwartz-nq2yy Жыл бұрын

  What exactly does this do to an x 3?raise engagement level to what rpm?d what gains come with it?

• 
  @aftermarketassassins5491 Жыл бұрын

  On most X3 models our clutch kits increase belt grip, but most importantly ramp RPM up quicker for better acceleration. Kits are adjustable for different tire sizes as well. Larger tires will slow down RPM and drop peak RPM, losing power. Our kits bring that back.

• 
  @BarrySwartz-nq2yy Жыл бұрын

  @@aftermarketassassins5491 what exactly comes in the kit and how much

• 
  @aftermarketassassins5491 Жыл бұрын

  @@BarrySwartz-nq2yy What year and base hp is your X3?

• 
  @BarrySwartz-nq2yy Жыл бұрын

  @@aftermarketassassins5491 19. 172. I have cat delete. Whalen 170 pump gas tune. 32 inch trail tires. It’s sluggish now. After the tires. I don’t want an high engagement spring.

• 
  @aftermarketassassins5491 Жыл бұрын

  @@BarrySwartz-nq2yy Our S2 clutch kit is a simple kit that will gain RPM back from the 32's and make it much more responsive. It engages close to factory and usually 2000-2300 which is smooth. aftermarketassassins.com/products/ols/products/aa-can-am-x3-s2-clutch-kit Thanks!

• 
  @toddteeters9031 Жыл бұрын

  Great video. My stage 3 is installed. We will know more in a few days. Heading to Winchester bay on Wednesday. WOT at 8750RPM, on MT'(32/12.50x15) on the wet pavement of the PNW. I suspect sand and paddles will pull it down where it should be. Will know more in a few days. Great product so far.

• 
  @aftermarketassassins5491 Жыл бұрын

  Yep, the sand load in the dunes will drop RPM between 200-400 RPM. Test in the flats when you get to the dunes and you should be right on. Thanks! -Mike

• 
  @thatoff-roaddude9515 Жыл бұрын

  It’s just something about the pro tho it sits perfect 🤷🏽‍♂️

• 
  @seymourclarkson2336 Жыл бұрын

  So if it already saves a stock tune I don’t have to pick or buy the stock tune on the website correct?

• 
  @aftermarketassassins5491 Жыл бұрын

  Correct. Just pick the tune levels you want.

• 
  @seymourclarkson2336 Жыл бұрын

  @@aftermarketassassins5491 so I can buy tune level 2&3 and when I plug it in,it’ll save the stock one like it did in the video?

• 
  @aftermarketassassins5491 Жыл бұрын

  @@seymourclarkson2336 Correct, unless it is a Polaris wideband model (blue O2 lead) or any Can-Am model in which it cannot read the stock file. We then provide you with the stock file.

• 
  @seymourclarkson2336 Жыл бұрын

  @@aftermarketassassins5491 how do I tell if mine is the wideband or blue O2?

• 
  @aftermarketassassins5491 Жыл бұрын

  @@seymourclarkson2336 See here: aftermarketassassins.com/tech-blog/f/rzr-turbo-evap-ca-models#

• 
  @colfaxent Жыл бұрын

  Surprised you don't mention anything about checking the rollers in the spider for excessive play or roughness.

• 
  @rick3446 Жыл бұрын

  Can Iuse this system to lower RPMs? My X3 is street legal and on the highway I'd like to drop the RPMs some. Thanks

• 
  @aftermarketassassins5491 Жыл бұрын

  Installing only our performance 1053 helix in your X3 would drop RPM roughly 200-400 RPM over stock, and lower cruising RPM for road riding, yes. You would want to use spring end hole C, quick adjust bolt hole 1. Thanks!

• 
  @rick3446 Жыл бұрын

  @@aftermarketassassins5491 Cool I just ordered it. Thank you

• 
  @dblsingletrack4292 Жыл бұрын

  I need this kit

• 
  @brittonmercer2258 Жыл бұрын

  I just ordered a 2023 Turbo r premium 4 seater. With a tune and a full exhaust how many horsepower could I gain.

• 
  @aftermarketassassins5491 Жыл бұрын

  That all depends on the fuel you want to run, but no matter what they have excellent horsepower to gain. Our level 2 tune with pump gas tuning you can be 195-200 crank horsepower. Our clutch kit is suggested to run that tune. To bump up to level 3 we'd suggest our charge tube, blow off valve, and slip-on exhaust. This would be around 210 crank. I would highly suggest our stage 3 lock and load kit: aftermarketassassins.com/products/ols/products/aa-rzr-pro-xp-stage-3-lock-and-load-kit

• 
  @MrJames6891 Жыл бұрын

  Some temporary tips for driving 2022 xp pro with AA tune? Im probably going to email this morning because I am interested in adjusting my own mapping from off the shelf

• 
  @aftermarketassassins5491 Жыл бұрын

  This article should help you: aftermarketassassins.com/tech-blog/f/pv3-gauge-setupmonitoring-for-turbocharged-vehicles

• 
  @robertonavarro7714 Жыл бұрын

  Been wanting to sell my XRC to get a pro R for the longest. Great work, that thing looks like it rips hard.

• 
  @MotoJeff117 Жыл бұрын

  This thing looks like it absolutely rips!!!! Great job guys

• 
  @bobbylane9166 Жыл бұрын

  Is there a reason why you wouldn't lube the pins while you have them out?

• 
  @aftermarketassassins5491 Жыл бұрын

  Certainly a bit of anti seize or high temp grease LIGHLTY on the inside diameter of the weight will help against corrosion. This can however attract dust, so if often riding behind others creating dust, use caution.

• 
  @r-yesdavid4831 Жыл бұрын

  So, whit this thing I can reset mi current miles to 0 miles ? In the case if a restore mi engine.

• 
  @aftermarketassassins5491 Жыл бұрын

  Sorry that is not possible as mileage is not able to be edited as it's stored in a different part of the ECU/gauge.

• 
  @r-yesdavid4831 Жыл бұрын

  @@aftermarketassassins5491 thank you, i appreciate your time to help.

• 
  @victormuniz2609 Жыл бұрын

  What year can am is this

• 
  @aftermarketassassins5491 Жыл бұрын

  2020 RR