Пікірлер

• 
  @Unranked.Күн бұрын

  Will this work on fma chassis?

• 
  @alfredolaurel-oz7nz Жыл бұрын

  Ur voice is shaking...ru alright?

• 
  @naldrus64182 жыл бұрын

  I hope when you that set up make some demo run..................... 🙄😒🙄😒🙄😒🙄

• 
  @stepanushandoko733 жыл бұрын

  Tulisannya sangat mengganggu sekali ... 😭😭😭 Tidak kelihatan dengan jelas ...

• 
  @JK-zo8qf3 жыл бұрын

  Do you giveaway free mini 4WD pls.

• 
  @Diamondbac3 жыл бұрын

  Is that the Winning bird polycarbonate body?

• 
  @kevinroi3 жыл бұрын

  Great video! Is it possible to add a pivot setup plus the ojapro body damper?

• 
  @Khanhnguyenphotography3 жыл бұрын

  This is probably the best upclose explanation on the front AT system. Thanks for sharing.

• 
  @boomerangE104 жыл бұрын

  Could you make tutorial video at the rear side for this AT bumper system..Iam newbie.. 😅

• 
  @theprofessor.m4d3094 жыл бұрын

  boomerangE10 I will be doing a rear AT system video in the next couple weeks.

• 
  @zomgsako4 жыл бұрын

  Thanks, very insightful. Def gonna make it on my next build. No grease needed between the carbons?

• 
  @theprofessor.m4d3094 жыл бұрын

  Michele Ferri you’re welcome! It’s kinda personal preference to grease the sliding damper or not. Some use none, some a little oil, others hard sliding damper grease. I figured this system was advanced enough that people making it would do what they are used to for lubricant.

• 
  @jonli94874 жыл бұрын

  Awesome video

• 
  @GCe_Tube4 жыл бұрын

  4 roller not allowed in asia

• 
  @theprofessor.m4d3094 жыл бұрын

  GC Tube Hi, official Tamiya rules since 2018 is unlimited rollers. That is what is used in Japan, it’s used in the US which are the two countries I race in. If your country uses other rules, then you need to adapt what you see to it.

• 
  @dhiyamohammad17565 жыл бұрын

  what part did u use for the rear under guard?

• 
  @theprofessor.m4d3095 жыл бұрын

  Hi, rear is standard anchor setup with underguard very similar to Roscoe Channel rear anchor.

• 
  @gonahoo20635 жыл бұрын

  Question!! 5mm pipe external diameter is 3mm But hole is 2.9mm?

• 
  @theprofessor.m4d3095 жыл бұрын

  2.9mm because your drill is likely not perfectly straight and you need to file a little to make everything smooth anyways. So start with slightly smaller hole and then open it up slowly so the sizes match better and there is less play in the system.

• 
  @pinoyking73135 жыл бұрын

  Awesome video. Ima do that

• 
  @SuperJsToysChannel5 жыл бұрын

  thank you very much for sharing your experience. I made my one today followed to your video.

• 
  @mianelucienlara79955 жыл бұрын

  thanks for this tutorial, now its more easier to understand this AT bumper system:)

• 
  @Z3NBluster5 жыл бұрын

  Excellent Work Professor!

• 
  @allandiamante40905 жыл бұрын

  nice

• 
  @Holybastard885 жыл бұрын

  Hi. I tried doing your at bumper but i used a pivot instead. I was wondering if you also have a tutorial to make the sliding damper? Thanks

• 
  @theprofessor.m4d3095 жыл бұрын

  Hi, I don’t have a tutorial for sliding dampers. They are annoying to make so I just buy mine from others who make them. I know Mad Tang sells them. I have some ideas for an AT system with pivot bumpers, but need to experiment a bit to see if it will work correctly.

• 
  @giorgiowjan2145 жыл бұрын

  Great tutorial, new sub 😜

• 
  @theprofessor.m4d3095 жыл бұрын

  Thanks!

• 
  @mattsosa68255 жыл бұрын

  Thanks Steve! See you at dxn :)

• 
  @telecaster1788545 жыл бұрын

  Thank You. It's very useful

• 
  @theprofessor.m4d3095 жыл бұрын

  Thanks for watching! Hopefully it helps.