Пікірлер

• 
  @mubashirshah510821 күн бұрын

  QUESTION REGUARDING SPACE COMPLEXITY: assuming we remove "int z = 9" wouldent the space complexity still be O(n) because of the fact that we have i in the for loop which would take space n times

• 
  @brooklyninja24 күн бұрын

  Thank you, great video

• 
  @joaquingibanel597629 күн бұрын

  Well done :) I will try something like that on my Launchkey Mini MK3

• 
  @thnxm8Ай бұрын

  the reason the order is weird is because the difference between adjacent bits must be minimal (1).

• 
  @JesseBakerHАй бұрын

  just picked up an old keyboard on ebay for SUPER CHEAP and it had a few dead keys. I had no idea the little rubber bumpers were conductive. Alcohol and a QTIP did the trick. :)

• 
  @samturner2716Ай бұрын

  Thanks for this. I already cleaned mine and that didn’t help. Going to try the conductive paint 🤞

• 
  @anstjd_ysАй бұрын

  Great explanation

• 
  @murilosena37092 ай бұрын

  GOOD!!!

• 
  @beyinvekalp2 ай бұрын

  Thankkkk you so much :hap🥰🥰🥰

• 
  @BlondieSL2 ай бұрын

  It's not clear to me (or perhaps I just missed it) but when the crazy glue didn't work, did you just stick the copper tape pieces to the carbon surfaces with nothing more than their sticky back? Or did you find a better way? I'm suspecting that after a short while of use, they would just fall off as there's no pressure to keep them in place. So I'm wondering if anyone has tried a better method to adhere these pieces? I haven't tried it as my MPK is working just fine, but I have some remote controls that use the same membrane to carbon contact method, that I need to fix. So as for the copper tape, I wonder if removing the sticky from the back, then using a small rotary tool bit, very fine and removing all that carbon contact surface on the membrane, would then allow the cop to be crazy glued or perhaps some other type of glue, might work. I'm not sure the best method of removing the sticky back from the copper, but there must be some chemical that we could use to soak it. I'll have to check, but I suspect that I bought a roll of copper tape that doesn't have a sticky back. If so, then this is a moot point. Then I only have to consider the best way to gently remove the carbon coating from the membrane. I'm' thinking that with bare copper to bare membrane material (I'm not sure if that's real rubber or some other stuff), it might be easier to glue the copper pieces so they'll remain flat and stick without falling off. Has anyone come up with a way to do this that works? As for the copper, when I do this, I'm going to see if either a hole punch will make perfectly shaped contacts, but if too big, perhaps using my leather hole punch as it has different sizes and even different shapes. There has got to be a way to fix these types of contacts!

• 
  @sonisona14192 ай бұрын

  Thanku sir❤

• 
  @anujkumarjha41692 ай бұрын

  Thanks bro

• 
  @heileychan49102 ай бұрын

  thanks a lot

• 
  @cicakmuhamed2 ай бұрын

  Important note: After you finish this CYK algorithm, if the starting symbol of the grammar (in this case S) is in the top-row (last row) of our procedure, then the given input string is part of the grammar, otherwise it is not. In this case S is part of {S, A, C} which means that the given input string "baaba" is part of the grammar defined by the production rules. The time complexity of the CYK algorithm is O(n^3) where n is the length of the input string (in this case "baaba", so n=5).

• 
  @AlaniHill2 ай бұрын

  the white background fried my eyes thank you

• 
  @serignembackecoulibaly98642 ай бұрын

  thanks you

• 
  @Izamu2 ай бұрын

  I wonder if the author will respond on my comment, but I wanna thank him anyways. It was useful, thank you

• 
  @mustafaturgut99302 ай бұрын

  dude your 8 is mutant

• 
  @louwashe2 ай бұрын

  my god thank you so much

• 
  @smikkelbeer78902 ай бұрын

  Thanks. Unfortunately this method seems to be excruciatingly long to work out especially if your string is like 6 to 7 symbols long.

• 
  @_inetuser3 ай бұрын

  +++

• 
  @adamjahani44943 ай бұрын

  Bro explained this so well. Such a hard concept

• 
  @yorsh.x3 ай бұрын

  fixed mine!, last C key was not responding and now it's like new. thank you. There's no need to take out the flex cable if you keep the plastic cover near

• 
  @DavidValle-ej8es3 ай бұрын

  Honestly Im glad you explain as if I'm stupid because I am

• 
  @user-kv5xt4ph4y3 ай бұрын

  Thank you so much. You saved me.

• 
  @user-aso0omy3 ай бұрын

  Thank you

• 
  @hibaabdirizak44524 ай бұрын

  Amazing video

• 
  @h-ym2ul4 ай бұрын

  Loved Your explanation of this video on this topic

• 
  @Mashayach74 ай бұрын

  The part I was missing is that the compiler has to work it's way back up the chain, that really made the concept click for me. Thanks!

• 
  @tanverhassan63984 ай бұрын

  Sound quality is so poor

• 
  @Gamuss123455 ай бұрын

  Can someone explain to me why it's a 1 in 2:42? I thought it has to be 0 as it's a positive binary number.

• 
  @Speedycey5 ай бұрын

  After many years, still a gold to watch. Your video is better than all free AI explanations.

• 
  @samidorian5 ай бұрын

  can I use the rubber piece that lies on the circuit board (I believe it's called a contact rubber, but I'm not sure) for the MPK261 as well? I've had an AKAI MPK261 sitting with me for about half a year, but I can't use it because the rubber is torn and brittle. for months, I've been searching for replacement parts but can't seem to find anything. therefore, i'm curious if the rubber from the smaller MPK models can be installed into the larger version...

• 
  @BlondieSL2 ай бұрын

  I know that your post is over 3 months old and you've probably already discovered that this will probably not fit. But, by any chance, do you have a 3D printer, some Flexi filament and the ability to use a CAD program, like Fusion 360, for example, to design a replacement that might work? Just a thought.

• 
  @user-im8pt3ef5m5 ай бұрын

  Obsessed with your voice 😂❤

• 
  @kittye82376 ай бұрын

  I don't even know English, but I managed to understand it easily. Congratulations, your way of teaching is fantastic!

• 
  @stewartcohen76836 ай бұрын

  Thanks for posting this! I have a 10 year old version that had over 6 dead keys. Even though I have copper tape, I bought some conductive paint and coated all the pads. I figured once I started, I should just make the whole thing work right for a few years! But I was ready to toss it, so great tip.

• 
  @BlondieSL2 ай бұрын

  It's not clear... are you saying that the conductive paint did NOT work?

• 
  @stewartcohen76832 ай бұрын

  @@BlondieSL The conductive paint did work! The copper strips did not.

• 
  @BlondieSL2 ай бұрын

  @@stewartcohen7683 Oh now that is great news. Would you please be so kind as to either post a link to the specific conductive paint your used or at least its full name. I have a few remote controls that I need to resurface the membrane contacts to get them working again. With these remotes, it's not like I can just order/buy new ones. They no longer exist and each one can control a whole bunch of devices. These are Logitech Harmony 665 and 650 remotes. I for one would really appreciate it. Thanks in advance.

• 
  @stewartcohen76832 ай бұрын

  @@BlondieSL One more thing...brush it on well, and let it dry for a day or so.

• 
  @BlondieSL2 ай бұрын

  @@stewartcohen7683 There's a lot of products that call themselves "conductive paint" and come in different formulas. So, specifically, which brand did you use? I just remembered that you prob. can't post a link. LOL I'm so forgetful this week. LOL So, full name of the one you used successfully would be appreciated. Thanks

• 
  @FullKarenMusic6 ай бұрын

  Looks to me like the black electrical isolation paint used inside Ibanez guitars. It acts like a faraday cage but it's also conductive black paint.

• 
  @BlondieSL2 ай бұрын

  I wonder if what you are talking about is possibly Aquadag?? I'm annoyed with myself that when I got out of the TV repair business, I let all my cans of Aquadag go. That's a conductive spray paint that is sprayed on a CRT's bell so that a grounding spring can lay across it. That stuff works so well, but I can't even find it anymore. I'd love to see if that would be an option as it does stick very well.

• 
  @FullKarenMusic2 ай бұрын

  @@BlondieSL You might find it at a guitar luthier supply website. I've only seen it as brush on.

• 
  @BlondieSL2 ай бұрын

  @@FullKarenMusic Thanks for that. I did find some and brush-on is perfect.

• 
  @staticx20136 ай бұрын

  This video is the greatest. Thank you for making it.

• 
  @amirbarjakli33836 ай бұрын

  ty for video :)

• 
  @izkustvo6 ай бұрын

  it works! thanks

• 
  @tobygeo7 ай бұрын

  What do you mean it can float? What is this, water? /joke

• 
  @sarparslan80357 ай бұрын

  Very good explanation thank you sir!

• 
  @user-pl9cm2nc5z8 ай бұрын

  the tutorial was not interesting ,you sound low.

• 
  @rold72568 ай бұрын

  I think you have to clear the concept clearly before teaching how mother fucker came here to waste time

• 
  @twilightbiscuit8 ай бұрын

  ok, sweet! some of my keys are dead aswell, I cleaned the keys but apparently I have to take care of the rubber thingys also, thank you!

• 
  @user-gm2kz5vl1w8 ай бұрын

  Good explaination thanke your f❤

• 
  @dominikbaricak95899 ай бұрын

  0.75 is not 110 its just 11

• 
  @lostsoulcar71309 ай бұрын

  is encoder=multiplexer and decoder=demultiplexer

• 
  @ferialebouariche99469 ай бұрын

  thaaaaaaaaaaaank you so much I spent a lot time on KZread to understand, finally i understannnd

• 
  @AndySamuuMSP10 ай бұрын

  straight to the point, thank you 8 years later