Пікірлер

• 
  @peterhansen821612 күн бұрын

  see how many times you turn the shaft to turn the drum 1 time.

• 
  @georgec779812 күн бұрын

  Hi, I did and it's about 90 to 94 times

• 
  @georgec7798Ай бұрын

  Hi everyone, I just want to apologize for not answering or responding to your questions, I do not get alerted when someone answers or responds to my video so if you know how I can turn that on or get alerts please let me know because I don't want people thinking I'm ignoring them on purpose, especially when they're trying to help me. Thanks for all your help. Even to this day I did not find the problem why heat is coming out and I still have the heater core bypassed

• 
  @osvilego1440Ай бұрын

  did you checked if the secondary pump should work in a sort of switch-on / switch-off mode and, for some reason, is always on?

• 
  @georgec7798Ай бұрын

  @osvilego1440 That could be but I'm not sure how to test it. I did put the digital meter on the wires going to it while the car was hot but it didn't show a reading more than a few MA.

• 
  @huntingwithredsАй бұрын

  What is the belt size

• 
  @georgec7798Ай бұрын

  Hi, sorry I guess I didn't put any numbers in the description I was kind of busy that day. Try pausing the video at 11:20 both the drive belt and deck belt are shown .

• 
  @georgec77982 ай бұрын

  I just want to give everyone an update on this refrigerator repair / mod. It's been more than 3 months and the refrigerator is working perfect. I am 100% sure that the relay I installed will last 10 times longer than the original

• 
  @chrismitchell35775 ай бұрын

  Mercedes Shhhmeraidese . High class piece of junk in my humble opinion.

• 
  @georgec77985 ай бұрын

  Every car breaks down and has problems, don't forget this car has over $280,000 miles on it with the original engine and transmission that still runs great

• 
  @jeremyrojas89425 ай бұрын

  When your at a stand still & twist the throttle and hear a click its supposed to do that, no ride the scooter give a couple push steps and twist the throttle it will engage the motor!

• 
  @georgec77985 ай бұрын

  Yes normally when the scooter is working but mine was not working no matter how fast I pushed the scooter

• 
  @lamprossavvas13926 ай бұрын

  Hi, thanks much for your differential rebuild videos, doing all the work for showing the entire process. I've learned a lot from it.

• 
  @lamprossavvas13926 ай бұрын

  Good work! Thanks for doing all these videos, very informative and helpful 👍

• 
  @lamprossavvas13926 ай бұрын

  The dryer is for keeping moisture and particles out of the a/c system by binding it. This prevents damage because of remaining moisture in the system, that can cause corrosion, quick oxidation of the compressor oil, all leading to excessive wear of other components like the compressor. The moisture can lead to icing of the expansion valve leading to declining cooling capability of the a/c. The dryer cartridge should be renewed from time to time because it has a maximum moisture binding capacity. It is strictly necessary to insert a brand new cartridge every time you open an a/c system, because the contact to the natural moisture of the outer environment leads of the instant saturation of the old dryer cartridge. After inserting a new one, the system has to be closed as fast as possible and filled up quickly with freon again, to prevent the new cartridge to be saturated and become useless in fulfilling its function. A drying cartridge isn't expensive.

• 
  @georgec77987 ай бұрын

  It's funny sometimes in my videos I call this a transmission because it reminds me of a small manual transmission.

• 
  @phantasm98 ай бұрын

  What is that small hose? My friends car doesnt have that small hose at all...just the 2 big hoses connected to the plastic firewall

• 
  @georgec77988 ай бұрын

  Hi, are you talking about the small hose that is covered with the plastic covering that is located near the battery because it's not an actual hose, I think it's the battery cable but I forgot

• 
  @user-mf9bq9ve2r9 ай бұрын

  hypothetical wondering if you could wired /soldered another relay and essentially jumping the two with 3rd one to turn on off the two relays ?

• 
  @georgec77989 ай бұрын

  Hi, this video is kind of old and I actually forgot what I did because I haven't viewed the video in a while. I think you're saying you want to use another relay as a switch instead of putting a jumper. Yes if you can fit the relay into the scooter then it should work but there would be a lot of wiring to do with positive and negative leads. If this is what you want to do, you can just put a toggle switch.

• 
  @user-mf9bq9ve2r8 ай бұрын

  @@georgec7798 i was just wondering if it was possible cause i have done that with computer on a van to figure out problems i was having .. the esc in this vid i had got working then it fried so i ordered a cheap newer esc to work with brushed and brushless motors seems to be best solution ..thanks for the reply and the vid id rather fix bypass stuff to make it work or preform better ... buying new is last resort i believe in you can do anything if u believe you can and practice fail and learn how not to do things ...so try and dont give up do research and prevail

• 
  @georgec77987 ай бұрын

  @@user-mf9bq9ve2r Yeah I know what you mean, I hate spending money when I don't have to

• 
  @TracyWolzfelt-pn8wg9 ай бұрын

  Just got this 🛴 4 months ago

• 
  @BYT21010 ай бұрын

  Did you need to evacuate the system before you took it out?

• 
  @georgec779810 ай бұрын

  Hi, sorry for the late reply but I don't get alerts and I don't go on KZread that much. Yes you definitely need to evacuate the freon because there is a lot of pressure

• 
  @TheGMan.11 ай бұрын

  Great video thank you

• 
  @aktherhoosensyed9110 Жыл бұрын

  Are u certain it is the heater valve ,normally when your catalytic convertor on the exhaust is blocked then it gives off extreme heat somewhere near the center console just above the exhaust

• 
  @karlschwab6437 Жыл бұрын

  Must be kick-started!

• 
  @Noor3368 Жыл бұрын

  thanks for video

• 
  @matthewcowart6713 Жыл бұрын

  I have this green one also I want to have no push off how do I eliminate that

• 
  @georgec7798 Жыл бұрын

  Hi, sorry for the late reply but I don't get alerts for this KZread. If you follow the instructions you could eliminate having to push the scooter.

• 
  @mechatron2775 Жыл бұрын

  good job

• 
  @JonahNAloha Жыл бұрын

  All I did was over volt with a 36v battery. Maybe it will work for you

• 
  @JonahNAloha Жыл бұрын

  All I did was over volt the system, try a 36v battery.

• 
  @jurez8752 Жыл бұрын

  very good tip George , I did the rework with a soldered jumper wire and it worked very well. The brake motor disable feature still works ! OTOH , the kick-start requirement is no longer available.

• 
  @georgec77989 ай бұрын

  Interesting.

• 
  @hectorestrada6048 Жыл бұрын

  Video is too long and sounds like he's not sure. Way too confusing.

• 
  @amberadkins3266 Жыл бұрын

  Do u still have the car ?

• 
  @gamerepair2020 Жыл бұрын

  Yes

• 
  @samkey599 Жыл бұрын

  What waz the problem of the AC?

• 
  @georgec7798 Жыл бұрын

  Hi, sorry for the very late reply I have this KZread account on an old phone. The problem was the AC was not blowing cold

• 
  @samkey599 Жыл бұрын

  @@georgec7798 ok, thanks

• 
  @wilsonk Жыл бұрын

  Nice sharing my friend.. watching from Malaysia

• 
  @sohypnodiq Жыл бұрын

  Thank you so much for sharing this helpful vid. My neighbor put a razor moped to scrap pile and I decided to attempt to salvage it. I bridged the relay as you demonstrated and wowla

• 
  @billywaynehuggins85672 жыл бұрын

  You had the exact same thoughts I had why in the hell run on the back side of the belt but thank you your info helped

• 
  @tserevenad2 жыл бұрын

  congrats on figuring this out. It has been a couple years, so is it still all working well at 39 degrees? So my real question is did you ever develop a theory as to why the control valve AND the relay failed? I am wondering if you had a current spike via a shorted battery/alternator/starter wire/lug incident. In simple terms what took out the control valve and relay?

• 
  @MadCrafted2 жыл бұрын

  E150 model most likely I have the same one.

• 
  @samueltalampas80602 жыл бұрын

  Hi sir. I have the same issue in my razor scooter I have clicking sound as well so it means I need to change only the relay?

• 
  @bikerboysrus12 жыл бұрын

  this is not the safe way, this is the best way to teach someone how to start a fire. most people don't understand what gauge wire to use. bypassing the relay will and is giving more amperage to the motor and straining the batteries, causing them both to fail quickly if the wire doesn't melt itself thru the plastic. the SAFE ways are to either by the 10$ speed controller new or desolder the relays and put new ones in. they cost 5$ if you use the pins this guy shows you to solder a wire in and bypass them, your soldering the wrong pins and also taking the long way around a simple fix. so much fail in one video but at least you were trying to help people

• 
  @jasonpang5312 жыл бұрын

  What is the root caused for this problem?

• 
  @OHydroTsunamiO2 жыл бұрын

  Dude corrected himself saying "sucks" 💀

• 
  @rollyguiling8582 жыл бұрын

  I bought a new controller but the motor still not working, I test the cable going to motor and it is zero reading, battery is fully charged 25.6V, there's click when I turn on the throttle but no power going to motor, I also checked the brake and it's fine, I already feed up, why there's no power going to motor?

• 
  @georgec77982 жыл бұрын

  Hi, you probably have to kick-start it or you can jump the relay like in the video. In other words, you have to kick-start it like a skateboard and then turn the throttle as it's moving

• 
  @thewoodbooger5832 жыл бұрын

  Thank you. Worked like a charm!

• 
  @mustaphaattebaa67142 жыл бұрын

  Hi,thank you very much with your video i repair my bicycle Razor E100.good job

• 
  @OE-jy6yt2 жыл бұрын

  Will try this solution thanks.

• 
  @ravimoodley70582 жыл бұрын

  What is part number of control valve

• 
  @georgec77982 жыл бұрын

  You can't go by the part number on the solenoid, you have to go by the number on the compressor which is shown in the video

• 
  @cantgetright_24_72 жыл бұрын

  Finally a video that'll just tell me how to get it working without telling me to buy all these parts and do all this testing. Exactly what I was looking for! Thank you!

• 
  @toppervikingo2 жыл бұрын

  100% right. I love when people take there time to explain what they think, according to many years experience and skills, how to fix a problem. Yes let us get more like that. George C videos are great:-) Every boddy can buy a new one - but that is not fun. Thank you George C:-)

• 
  @mntrout4002 жыл бұрын

  do you have any idea why my same car would still blow ac when I turn the heat on?

• 
  @tannerpatterson21182 жыл бұрын

  E175

• 
  @DylanL692 жыл бұрын

  60 bux ain't shit for a sensor and 55° is a good a.c. temp that's pretty fucking cold

• 
  @rileyclauser35852 жыл бұрын

  Hey, I tried the kick and go BS and after 3 days of messing with this scooter your video solved my problem. It might not be the "right" way but IT WORKED! Thank you!

• 
  @1mandanceparty2 жыл бұрын

  This video should have been like 3 minutes long. And honestly you didn't even show me what I needed. This was a frustrating waste of time.

• 
  @1mandanceparty2 жыл бұрын

  Please get to the point and show me where the bypass is located...

• 
  @georgecarmona18172 жыл бұрын

  Thank you for sharing

• 
  @ThePiemasteification2 жыл бұрын

  Thanks for the video! My E100 board looks nothing like that though :/

• 
  @thehouseofbaashainc.89022 жыл бұрын

  Your O2 Sensors are bad and needs to be replaced