Пікірлер

• 
  @flintcarlton3 күн бұрын

  How has it held up over the years? 😊

• 
  @diymechanic55033 сағат бұрын

  Great! Still looks as it did when I laid it down. Just a little dirtier :)

• 
  @maxywaxy336 күн бұрын

  Would you have the part number for that? I can not seem to find a replacement (I have the same fridge)!

• 
  @diymechanic55034 күн бұрын

  No, sorry.

• 
  @MattHavell2 ай бұрын

  Thanks

• 
  @donnyivy38322 ай бұрын

  Thank you for taking the time to post. Very helpful for owner's of old travel trailers.

• 
  @diymechanic55032 ай бұрын

  Glad it was helpful!

• 
  @nn96932 ай бұрын

  Thank you very much

• 
  @diymechanic55032 ай бұрын

  Any time

• 
  @user-si6gw4zy9v3 ай бұрын

  Awesome thanks

• 
  @diymechanic55032 ай бұрын

  Welcome 😊

• 
  @madisyntrevor3543 ай бұрын

  🔥 P r o m o S M

• 
  @diymechanic55034 ай бұрын

  Update: This fixed the problem with my front end dropping down after sitting.

• 
  @miltonjasso58434 ай бұрын

  GREAT MAN !!! THANK ALOT !! Ill be changing mine soon !!!

• 
  @diymechanic55034 ай бұрын

  Glad to help. Please subscribe if you find it helpful.

• 
  @maxxbenzz78425 ай бұрын

  Only the Germans design a clip like that.🙄

• 
  @diymechanic55035 ай бұрын

  Hahaha. Yup.

• 
  @maxxbenzz78425 ай бұрын

  The clip on my 03 E320 is completely different. Still haven't figured out how to get it off😢

• 
  @williammcmonagle526 ай бұрын

  Hi can I ask a question what milk should I use with coco pops to fill a pot hole on the road outside my house Semi skimmed or full. I’m sure I would have more success doing this than repairing my car with your crap video.

• 
  @diymechanic55036 ай бұрын

  I would recommend giving yourself an anima with whole milk.

• 
  @prabhu33027 ай бұрын

  Are both mounts the same on each side? There isn’t a right one and a left one right? Also what size was the offset wrench

• 
  @diymechanic55035 ай бұрын

  Its in the video. 16mm

• 
  @floridaman51257 ай бұрын

  What would be the cause needed to change this out? I have constant battery protection on at the moment.

• 
  @diymechanic55037 ай бұрын

  Battery protection could be one reason, but really anything that involves the battery. Most of the battery issues I have seen with this car have been related to the alternator/voltage regulator. I would start there.

• 
  @floridaman51257 ай бұрын

  @@diymechanic5503 both batteries and alt and voltage reg are new. I’m trying the auxiliary relay and if that doesn’t fix it, off to the merc specialist (not dealer!)

• 
  @diymechanic55037 ай бұрын

  @@floridaman5125 What is the car actually doing? Is it just an error message? No symptoms? Or are there symptoms?

• 
  @floridaman51257 ай бұрын

  @@diymechanic5503 2 things I can see: 1) turns on battery protection between 10 and 60 seconds when I start the car, and 2) I checked the voltage on the new aux battery and it stayed at 12.xx. The main was at 13.8x at the same time. If I change the relay and nothing changes I will take it in. The rear BCM looks clean. The codes are 9050 and 9051.

• 
  @diymechanic55037 ай бұрын

  @@floridaman5125 Well good luck! I'm stumped.

• 
  @Whereswheezy8 ай бұрын

  “ I’m gonna need a bigger screw driver” - Mechanics: felt that

• 
  @Salukian8 ай бұрын

  Hey! Thank you sir! Saved me ~$200

• 
  @diymechanic55038 ай бұрын

  Good job!! Glad you fixed it.

• 
  @johnfader7119 ай бұрын

  thanks man. mine was same problem. all fixed now!!!

• 
  @JohnVantine0110 ай бұрын

  The screw seems to be rusted into place, and it's hard to get a good angle on it to apply enough pressure to unscrew. Any tips on how to gain access to behind that panel, or some other way to clean that tube out without taking off the metal panel that covers it? Thanks so much!

• 
  @diymechanic550310 ай бұрын

  You will have to get that cover off to access the tube. Have you tried spraying some PB blaster or something on it? Even if you have to cut the screw off you can replace it, its just a standard sheet metal screw. Hope this helps.

• 
  @ricattinog3449 Жыл бұрын

  Many thanks! I was trying to take that off for 20 min without success.

• 
  @diymechanic5503 Жыл бұрын

  Hahaha. It's a bugger. Glad it helped.

• 
  @temirtaragay8932 Жыл бұрын

  If you push on that button propane will come out. I tried that and big flame was ignited but the fridge did not ignite. Luckily I was not hurt.

• 
  @diymechanic5503 Жыл бұрын

  Not sure what button you are referring to, but I don't mention anything about pushing any buttons. I would not recommend you attempt to work on your RV.

• 
  @possumjenkins007 Жыл бұрын

  Thank you so much! This saved me a lot of time and frustration.

• 
  @diymechanic5503 Жыл бұрын

  Glad it helped!

• 
  @mohamedazkoul9544 Жыл бұрын

  I changed the battery for a W211 E320 , the car starts then the fan goes at full speed ..doesn't engage any gear it's showing the battery sign on the dash... i tried diagnostic tool it's not showing any fault codes Any ideas ..can it be the BCM ?

• 
  @diymechanic5503 Жыл бұрын

  Sounds like something more may be going on with your issue. Not that familiar with the W211, but have you checked your alternator/voltage regulator?

• 
  @mohamedazkoul9544 Жыл бұрын

  @@diymechanic5503 the alternator was shot I over hauled it , new rectiftor, Voltage regulator and bearing .. tomorrow I will intsall it and I hope everything will be back to normal.

• 
  @diymechanic5503 Жыл бұрын

  @@mohamedazkoul9544 Very nice! Let us know how it goes.

• 
  @mohamedazkoul9544 Жыл бұрын

  @DIY Mechanic Thanks but not a good news , I installed it the engine fired up for 1 min and died , there is no fuel pressure, there is no power to the fuel pump, the fuse and the rely are fine.... I don't know what happened. ..the car is in prefect condition driven only 95K km's the battery dead for 1 month before that everything was fine.

• 
  @mohamedazkoul9544 Жыл бұрын

  I took to a mechanic because I can't DIY this problem, the main wirring harness is eaten by a mice , after connecting few chewed wires he was able to start the car yet , the accerlator is not working.

• 
  @warrenmullett Жыл бұрын

  We use a similar tape in underground gas pipes.. I’m actually pretty sure it’s the same thing. If properly installed it prevents the steel pipes from corrosion for tens of years.. seems like a roof would be no problem for this “tape coat” which is what we call it ..

• 
  @youngjung4361 Жыл бұрын

  What go bad to replaced the BCM?

• 
  @diymechanic5503 Жыл бұрын

  could see an error such as "AUX equipment turned off" or something to that effect. I was getting an error that my battery was not working properly but I was getting a good voltage when I measured so it was very strange. It turned out to be the voltage regulator on the alternator that fixed the problem. I made a video on that as well. Hope this helps!

• 
  @youngjung4361 Жыл бұрын

  As long as your battery is not drain when parked it's good to go. I have a 09 replaced battery 3 times in last 4 months. It was a pain. It was draining over 3 amps in 15 mins. It was the bad driver side seat module went bad. Took out the seat connector and reads less than 0.05 Memphis. All good so far. ...

• 
  @youngjung4361 Жыл бұрын

  Sorry for the typo. It's 0.05 M amp

• 
  @diymechanic5503 Жыл бұрын

  @@youngjung4361 Probably 0.05 mA not 0.05 MA :) Glad you found it, that's good information. Thanks for sharing!

• 
  @ChicoDeon Жыл бұрын

  Thank You very very much

• 
  @diymechanic5503 Жыл бұрын

  Glad it helped!

• 
  @allacestattoo Жыл бұрын

  I have a 2004 c240 both door handles are broken. Local shop $620 labor alone to replace. I'm going to tackle it myself. Thanks for the video.

• 
  @diymechanic5503 Жыл бұрын

  Love it. You will have no problem doing it.

• 
  @PatrickSteil Жыл бұрын

  Thx for the video!

• 
  @jwamerica84 Жыл бұрын

  Seems to me this controller was not much of an upgrade over the OEM unit.

• 
  @diymechanic5503 Жыл бұрын

  Main thing is having the probe inputs. The old controller didn't have that.

• 
  @sailkat59 Жыл бұрын

  It worked for me as well. Mud dauber at the end of the tube. Fixed it!😀 Thanks for sharing your knowledge!

• 
  @georgedoughty6679 Жыл бұрын

  Caught one the first day I got it. The best

• 
  @diymechanic5503 Жыл бұрын

  Awesome!

• 
  @jomariothomas6585 Жыл бұрын

  I just changed out the batteries and alternator due to a constant low convenience power. A couple weeks later I see the "visit workshop" and "battery/alternor stop vehicle". Now looking at this video, I'll take a look at the bcm. Any additional advice or recommendations to look into?

• 
  @diymechanic5503 Жыл бұрын

  If you just changed the alternator then got this warning, I would go back and make sure everything got hookup up correctly. I think it is unlikely to be the BCM but you never know. Good luck!

• 
  @jozopap53117 ай бұрын

  Is it neccesaey to disconnect main battery before changing bcm And also,when changing,first disconect minus cabel and then the jack?

• 
  @lilburkegamezАй бұрын

  Did it work

• 
  @nadowayne Жыл бұрын

  Great video and this will be the second time I’ve had to do this on my refrigerator. Living on the coast makes more rust and driving from San Diego to South Dakota and then returning on very rough road repair areas caused more rust to fall in again. Thanks for the video.👏

• 
  @Uncommon_Valor2 жыл бұрын

  thanks for this, great video

• 
  @zac09122 жыл бұрын

  Use Dicor for sealing vents and such. There is a reason MFG's do, look at you vents in the background. Eternabond is the lazy route. Eternabond is a patch and should be used as such. Have fun getting the residue off when it needs replaced, not the same issues with Dicor. This will show you what I mean kzread.info/dash/bejne/h3ZsxNhvYajWpbw.html

• 
  @diymechanic55032 жыл бұрын

  I use dicor as well. The tape is holding up just fine. I don’t plan on ever removing it until it’s time to put a new roof membrane down.

• 
  @JosephOster2 жыл бұрын

  "Make sure you don't cut through your [new/old] roof." - DUH!! You could have placed a board under the tape before using the blade to cut it, eh? Not sure there's any point to watching further after a mistake like that!

• 
  @diymechanic55032 жыл бұрын

  whatever bro. I didn't cut my roof, I was cutting on the flange of vent. Thanks for the comment.

• 
  @JosephOster2 жыл бұрын

  @@diymechanic5503 Look again at the 0:58 sec. mark.

• 
  @diymechanic55032 жыл бұрын

  @@JosephOster bottom line, I did not cut my roof because I took my time and was careful. Still holding up as good as day one. Thanks for your concern and suggestion for others.

• 
  @Bsrgoent88252 жыл бұрын

  V

• 
  @tomchrishawkins2 жыл бұрын

  Did what you said, and what many others say, to clean out the burner and flue. But, that was not my problem. I discovered that orifice was clogged. Real easy to take out, and cleaned out with a very small needle, and worked great again.

• 
  @diymechanic55032 жыл бұрын

  Yeah I should have mentioned that as well. Glad you got it going!

• 
  @larissarobinson1862 жыл бұрын

  IT WORKED!!!!! I thought I was in for a visit to a repair man but you have solved a very frustrating problem. Thank you so so soooo much!!!

• 
  @williamkemphill35612 жыл бұрын

  Show me where the fuse for the wiper in the wiper pump

• 
  @diymechanic55032 жыл бұрын

  Sorry, I no longer have this vehicle but it is where all the other fuses are. You just have to find the one labeled Wiper pump. I think it is in a black box under the hood right in front of the driver.

• 
  @wyattt.ginter81382 жыл бұрын

  That was very helpful! Thank you!!

• 
  @LT-uq6dg2 жыл бұрын

  I didn't have luck w this. Gopher kept disarming it w dirt or just dig another tunnel. Finally used a water hose to flood him out then shot it when it surfaced. Took 2min

• 
  @diymechanic55032 жыл бұрын

  Yeah, that happens sometimes. Usually means you need to get further from the hole. Anyway, glad you got the varmint.

• 
  @andrewsilverman79542 жыл бұрын

  Great detail, camera work and explaining!

• 
  @doublej22122 жыл бұрын

  Bring a cutting board next time you made me nervous!!

• 
  @BULLDOGTough2 жыл бұрын

  Great set-up! 👍

• 
  @diymechanic5503 Жыл бұрын

  Thanks! 👍

• 
  @fernandopaulino22212 жыл бұрын

  Hi, do you know of a Company tha Refurbish the Battery Control Unit 230-540-10-45-80

• 
  @diymechanic55032 жыл бұрын

  No I don’t. Sorry.

• 
  @bulletsponge632 жыл бұрын

  What is the length of that farm jack?

• 
  @diymechanic55032 жыл бұрын

  48"

• 
  @inkbythebarrelandpaperbyth69052 жыл бұрын

  Awesome video. Think itll work in cold weather?

• 
  @diymechanic55032 жыл бұрын

  I don't see why not. Just make sure you put plenty of pressure on it. If you have a roller, use it.

• 
  @larrylindenmeyer43902 жыл бұрын

  Thanks

• 
  @diymechanic55032 жыл бұрын

  No problem

• 
  @nathanurick83202 жыл бұрын

  I think I would have put a board or cutting board under that tape before I tried using a razor on it

• 
  @ptsbc9412 жыл бұрын

  Hows it holding up after 3 years?

• 
  @diymechanic55032 жыл бұрын

  Perfect. Still looks great!