Пікірлер

• 
  @user-nk1sz2fg1u11 сағат бұрын

  วงจร😅ไฟขอบคุณครับ....a6 c5

• 
  @ed420.Күн бұрын

  What order do they number the cylinders? Is it 1 2 3 on the drivers side and 4 5 6 on the passenger side?

• 
  @grewvcannabis3 күн бұрын

  Thanks my friend. I replaced a broken spring today. It came out easier than the new one went in. My spring compressor wasn't the best and the straps slipped. I had to cut the straps off in the end too but the jobs done. Thanks for the help, It was terrifying at times.

• 
  @LuisVargas-mo5ew3 күн бұрын

  You forgot the grease and I messed up on my piston caliper I did counter clockwise and boom a bunch of oil comes out I was pissed 😤 now I have a rip on my rubber sleeve etc

• 
  @Liber_in_natura5 күн бұрын

  Mulțumesc!

• 
  @threeamigos8426 күн бұрын

  Did you go into the service mode to put the car into pad change option... it didnt say in the video. In other videos it mentions this.

• 
  @TheRuwester9 күн бұрын

  Thanks for the help!

• 
  @rosscopeeco6913 күн бұрын

  Thanks for this video. I was confused as previous owner had put the spring clips on wrong but your video sorted me out.

• 
  @Mcintechmobilemechanic14 күн бұрын

  No coper grece on the shims

• 
  @Mcintechmobilemechanic14 күн бұрын

  How about the calibration

• 
  @kyleellis742116 күн бұрын

  Perfect fix for my issue on my Audi A6 C7 2012. I had the same issue whereby everything worked on the mmi except the screen being black once fully opened. My screen actually worked initially then turned black half way through the opening/popping out cycle. Then was black thereafter. Turns out my cables were both split and needed repairing. Followed the steps and with a new fuse and works perfectly. Thank you for an informative and detailed video.

• 
  @sergiupaval908816 күн бұрын

  Thanks 👍👍👍

• 
  @joaocamboias371622 күн бұрын

  Na minha opinião deve-se sempre sangrar o circuito antes de empurrar o pistão/êmbolo para trás. Isto para não fazer retornar o lixo que se junta no êmbolo até á unidade de controlo do ABS. Estarei errado?

• 
  @beastbody584822 күн бұрын

  Hi, Where about you base mate? I have Audi A6 C7 facelift and I need some jobs.Im from South Yorkshire and I hope you not far away as I have few jobs to do with my Audi. I look forward to hearing back from you

• 
  @vakeiniux32128 күн бұрын

  Thank you! Really helped! Getting old one out was insanely hard... Had to break it to get it out... For the new one I just used silicon to seal it, that way I'm sure water wont get in 😅😅

• 
  @RyansWorkshop28 күн бұрын

  Happy I could help

• 
  @craigmushens4789Ай бұрын

  Did one spring last night without this tip and it was a chore. This method made it way easier to get the new stock height spring in

• 
  @RyansWorkshop28 күн бұрын

  Happy I could help

• 
  @bogdanozga4310Ай бұрын

  Thanks, it was very helpfull

• 
  @RyansWorkshop28 күн бұрын

  Glad I could help

• 
  @beastbody5848Ай бұрын

  Hi Mate, Where about you base in UK? I need good mechanic for my audi a6 c7 2.0 tdi ultra . Get back so if you close you have new customer. Thanks

• 
  @insus100Ай бұрын

  My car has the sensors in the back but has no button in the dashboard. There's a fault in VCDS and when putting reverse nothing happens on the screen. 01543 - Parking Aid Warning Chime (H15) 009 - Open or Short to Ground Replacing it would fix it? And why nothing shows on the mmi when putting reverse?

• 
  @Clue83Ай бұрын

  I have a similiar issue on my c 7.5 however it seems intermittent. sometimes the screen doesnt come out on startup and the retract button doesnt work along with the radio/media/nav etc. however sometimes it does and works fine. any ideas?

• 
  @daniellandqvistАй бұрын

  Thanks for an excellent video. Views, voice, explanation is just all perfect!

• 
  @RyansWorkshop28 күн бұрын

  Thank you, I'm happy I could help

• 
  @mariuszattarin9550Ай бұрын

  Great vid. Just what I was looking for. Cheers mate.

• 
  @RyansWorkshop28 күн бұрын

  Thanks, glad I could help

• 
  @jamesashton-an_sonsАй бұрын

  Great video pal very well explained

• 
  @RyansWorkshop28 күн бұрын

  Thank you

• 
  @carlosgibson4752Ай бұрын

  Thank you so much for this video, I’ve done my rear pads today and thanks to this video the job was very easy and straightforward! Audi quoted me £425 to change the rear pads! I bought brembo pads for £47 and used this video to fit them myself! Thank you!

• 
  @RyansWorkshop28 күн бұрын

  Happy I could help

• 
  @mrmaksimilianoАй бұрын

  Did it on the 2018 A6 Allroad. Worked out. Thanks much

• 
  @RyansWorkshopАй бұрын

  Happy I could help

• 
  @pilotdavoАй бұрын

  Thank you. Great instructional video. Really clear and well filmed. I'll get mine fitted when it arrives in the post.

• 
  @RyansWorkshopАй бұрын

  Thanks

• 
  @bobbybasic12 ай бұрын

  can you replace individual bulbs on the third brake?

• 
  @RyansWorkshop2 ай бұрын

  They don't have bulbs, they are soldered LED chips

• 
  @wayneskinner24952 ай бұрын

  Nice job.

• 
  @RyansWorkshop2 ай бұрын

  Thanks

• 
  @paho188_iron_phill42 ай бұрын

  thanks for guide, i need to change centre brake light on my audi a4 b7 avant hope its same

• 
  @RyansWorkshop28 күн бұрын

  Hope so

• 
  @anma7002 ай бұрын

  Great video but I am struggeling, I have an A6 C7 but not sport so my springs are alot taller (almost 5cm). First I thought I got the wrong springs but they are aproximate the size of the broken ones (millimeter difference). I had to compress them alot, about 5cm to get the bolt on the shock back in place and now I am at the situation where I cannot get it back in place using you method. I think the only way for me is to remove the upper controlarms but that is no easy task it seems like. Taking a break right now and pondering any options but cant see any yet.

• 
  @anma7002 ай бұрын

  I somewhat retract my comment, It was not possible to get much, if any movment of the shock with the spring compressors. I had them as tight as possible but the end started to touch the top. But what I tried was to lift the car as high as I dared and then used a long (2,5m) prybar get the controlarm as low as possible. Possibly some bushings that did not like that but they need to be changed anyway. Still was a fight with 0mm to spare but made it. I actually clamed the prybar down but if I have had help it might have been easier and a bit safer. Also had a prybar on the spring to get some movement upwards on that, might have been the last millimeter that made it. Anyway, happy now, atleast a few minutes until I start on the second side.

• 
  @RyansWorkshop28 күн бұрын

  Glad you got there in the end

• 
  @davemac31712 ай бұрын

  I just completed this job on my 2012 a6 c7. Your video made it very easy thank you

• 
  @RyansWorkshop2 ай бұрын

  Glad I could help 👍

• 
  @RobertP78842 ай бұрын

  did same on Audi A2 one side was ok with clamps but other where tank inlet is wasn't possible to use clamps so ratchet straps to the rescue

• 
  @RyansWorkshop2 ай бұрын

  Happy I could help

• 
  @felixfischer67952 ай бұрын

  Muss man die Spur danach einstellen?

• 
  @RyansWorkshop2 ай бұрын

  Hi, yes I would recommend it.

• 
  @LozzieUK2 ай бұрын

  Great and very useful, thanks. Any chance you could share the part number for the rear chime please

• 
  @RyansWorkshop2 ай бұрын

  Thank you, yes the part number is 8E0919279

• 
  @LozzieUK2 ай бұрын

  @@RyansWorkshop thanks, you are wonderful

• 
  @rashkomakov2 ай бұрын

  thank you worked for me

• 
  @RyansWorkshop2 ай бұрын

  Glad I could help 👍

• 
  @PS-sp3sb2 ай бұрын

  Do you know where is the control module for the glow plugs? Cuz i got a blinking light on the dashboard after i washed the car . Thanks for the vid!

• 
  @samuelallard12283 ай бұрын

  Hi! Great vid! I just have a question i have the driver side tail light on the trunk the led for braking et flashing not working anymore after a compound on it do you know what i have to change to repair that? Thanks!

• 
  @RyansWorkshop2 ай бұрын

  Thank you, I would suggest that there is a problem with the electrical circuit and the whole unit would likely need changing.

• 
  @PaulPoirier-xm3sl3 ай бұрын

  Ryan: I have a 2012 Audi A6. Thanks for the informative video! I followed your directions and rounded up all the components and tools I needed to complete the task. The most informative part of the video was the sequence of panel removal to get the MMI out. After repairing the wires, getting the wires jammed into the dashboard so they didn't interfere with the MMI operation was trickier than I expected upon reassembly. I got it dialed after a few trials. I started at 5 PM and project was completed in just over 2 hours! I had two broken wires, and there was evidence of a previous repair on mine. Works great. The thing I missed the most about the black screen was the backup camera. I found a work around for the radio on the screen between the Tach and the speedo, until I got it repaired. No blown fuses. Thanks so much!

• 
  @RyansWorkshop2 ай бұрын

  Happy I could help

• 
  @1000sofusernames3 ай бұрын

  I have just finished this job (sort of). What a nightmare. Caliper bolts came out easy enough but calipers took lots of persuasion to come off, lots of levering with a pry bar. Caliper carrier bolts were horrendous. I was able to get the impact wrench on one but the other one just didn't have the access to get the gun on it, couldn't get the breaker bar on it either even with the wheel turned out. Luckily I'd bought some decent spanners recently so the spanner and lump hammer whallops got them moving. Once I'd got those off the discs had of course fused to the hub. Plusgas and more hammer persuasion. Finally time to wind calipers in....then I realise I can't get my retraction kit in this type of caliper....g-clamps and bits of wood instead will do. Putting it all back together is ok....except the springs require the strength of Hercules and by this time its dark and I'm knackered. Finally get it dropped, torque wheels up and go for a drive.....brakes feel like a bit soft. Good job I've just bought a pressure bleeder. No doubt the bleed screws with be seized.... Even when buy one with a FSH it's still a grind and you wonder if half the garages never did the work that's claimed. Hopefully anyone else doing this has an easier job.

• 
  @RyansWorkshop2 ай бұрын

  Yeah these brakes can be quite tough sometimes, glad you managed to sort it though

• 
  @1000sofusernames2 ай бұрын

  Did the front control arms while I was at it. MOT passed. Job done! God knows what a Merc garage would charge.

• 
  @AMG196983 ай бұрын

  This is easy.Tell us how to change the Η7behind..........

• 
  @razvanski58823 ай бұрын

  big up

• 
  @jeffick3 ай бұрын

  Well done Ryan, made it look easy doing the a6 front and rear brakes

• 
  @RyansWorkshop3 ай бұрын

  Thank you

• 
  @stevebox24943 ай бұрын

  Cracking video, straight to the point without all the usual waffle, thanks a lot 👍

• 
  @RyansWorkshop3 ай бұрын

  Thank you, glad I could help

• 
  @goodbyetothepeople923 ай бұрын

  Where is the glow plug control module on a late 2020 model Q5? The engine management light is on and the diagnostic is returning the following error code “P0684 Glow Plug Control Module 1 to PCM Communication Circuit”

• 
  @theoptimist90943 ай бұрын

  Ryan your videos are the best- one request: could you cover where jack stands should go on a C7 Audi? I’m nervous for so many reasons and there isn’t any guidance out there that I’ve found

• 
  @RyansWorkshop3 ай бұрын

  Thank you, yes this is something I can cover in the near future

• 
  @theoptimist90943 ай бұрын

  @@RyansWorkshop Really look forward to it- you get right to the point as with dealing with the EPB without the diagnostic tools! I salute you, Sir!

• 
  @Dagr8soldjer2 ай бұрын

  There are plastic covers underneath the sills. Pop the retaining clips in the middle of the cover out with a flat head screw driver and then remove the covers. This will expose the jacking points.

• 
  @theoptimist9094Ай бұрын

  Thank you! I’ll give that a try. I wondered about how Ryan puts the jacks under the subframe and how to do that as in this video

• 
  @bkp83453 ай бұрын

  Thanks man. I'm trying to convert to led from hid and this definitely helped.

• 
  @RyansWorkshop3 ай бұрын

  Happy I could help

• 
  @dannylee08074 ай бұрын

  Good video thanks. Shouldn't people always warm engines

• 
  @RyansWorkshop3 ай бұрын

  Thank you, some say you should but I've never seen any benefit from doing it personally

• 
  @Rebenga894 ай бұрын

  How about audi a6 c7 facelift avant modell is the same to fixit???

• 
  @bartekzaj4 ай бұрын

  Why you did not use second and third clip?

• 
  @RyansWorkshop2 ай бұрын

  I did

• 
  @alwaysbluffme4 ай бұрын

  Nice tutorial.Thx mate!

• 
  @RyansWorkshop4 ай бұрын

  Thank you