Пікірлер

• 
  @goodun29743 күн бұрын

  As an audio-repair bench tech, I used a similar AOYUE desoldering station for 5 years before retiring; I didn't care for the solder-capturing spring inside the collection chamber and substituted a wad of medium-grade steel wool instead. The spring is too difficult to clean out unless you grease it, which is smelly and messy. I suggest you also test the tip included with the soldering iron to see if it is strongly attracted to a magnet throughout the tip and at the back end, or if it is only magnetically attracted at the tip (like it's supposed to be). Thermal transfer is far superior if the tip is made of plated copper, with iron plating at the pointy business end only, to prevent the solder and flux from eating away at the copper ---- but a lot of Asian manufacturers are making the tips out of solid steel or iron which is a much poorer conductor of heat. You can easily determine whether the tips are good or bad, with a magnet; I posted a video on my channel about this recently.

• 
  @angiutv58975 күн бұрын

  any ideas for the following fault. Son was watching TV, Sharp Aquos. half way through a progamme and it just switched off randomly and will not power back up. Showing no power at all. Changed fuse in the plug etc but no power at all. Any ideas. Its about 4 years old. Thank you

• 
  @waynephillips18485 күн бұрын

  If you are not getting the standby Light on its most likely a failed power supply, sometimes with switch mode supply's if you place your ear close the the TV and switch on the TV you can hear a ticking sound, if you hear this sound most definitely a failed power supply. Either way if the Power supply is faulty then a repair/service would be required.

• 
  @angiutv58975 күн бұрын

  @@waynephillips1848 yea, no standby light. no ticking noise at all. could it be a fuse inside?

• 
  @waynephillips18485 күн бұрын

  @@angiutv5897 Just looked at the service manual and there is an internal fuse, on my video at 57 seconds, look in the top left corner there is a white connector, just to the right and above is a brown soldered in Fuse, PCB designation FB1, rating T3.15AL 250V. Please read my warning in the description

• 
  @angiutv58975 күн бұрын

  Thanks I'll have a look. 😊

• 
  @peterperry15839 күн бұрын

  Im on that model right now placing the belts over the posts before attaching to the motor is pure genius thanks so much for that .

• 
  @KE8ODY-WV-Ares-Ham-Dad-3O417 күн бұрын

  I can’t find the linear setting only the ext tuner

• 
  @PranksFans18 күн бұрын

  price please?

• 
  @waynephillips184818 күн бұрын

  Total cost of hardware in GBP as of 2023 all brought from amazon £6.99 Printer Extension Cable USB 2.0 B Adapter Male to Female Connections £21.88 SUPERNIGHT 12V 30A Switching Power Supply £23.00 MACH3 Controller USB MACH3 100Khz Motion Controller Card Breakout Board £23.99 3 X Dealikee TB6600 4A 9-42V Stepper Motor Driver CNC Controller £10.00 4 Channel Relay Module, 12V 4 Channel Relay Module Optocoupler £12.88 Frequency To Voltage Module, 3.3V/5V/24V 0-100% 100HZ-3KHZ PWM to 0-10V £9.00 Various cable rap, fixing, cable ties Total =£107.74

• 
  @pedalpimpshop20 күн бұрын

  Just went through the caps and you have some mistakes: There are 5 X100uf caps and not 4. There are 20 X10uf caps and not 19. There are 8 X4.7uf caps and not 7 and 2 X2.2uf not 4. The power supply board caps are 1000uf, 2x220uf, 47uf. I’ve gone 50v with all caps.

• 
  @JamesSmith-tv3pz24 күн бұрын

  Great advice and pictures/images of the top mounting wear (the source of the 'clunk/knocking).

• 
  @cambridgemart207527 күн бұрын

  That's a weird failure for a polyester film cap at relatively low voltage. As you say, MOSFETs normally fail short, so good catch! For the drivers to fail is odd though as they are normally killed by a shorted MOSFET, although they are extremely sensitive to a difference in the voltage between the input and drive side ground voltages.

• 
  @burnessansell27 күн бұрын

  Hi Wayne, Loved your vids, got me set up. However, I have an interesting problem... I am running WSJT-X with my IC-7700 connected to my iMac (2017) running macOS Ventura 13.6.7. Everything appears to be ok on settings, Audio/Radio, etc. The problem is, when I go to transmit I can only get WSJT-X to transmit once and only once. Any subsequent transmissions without having to exit out of the software fail. I know I'm getting out on that one transmission, as I've seen signal reports on the PSKReporter. Any clues, suggestions, assistance would be appreciated in figuring out what might be going on. Tnx & 73, KI0AR

• 
  @waynephillips184827 күн бұрын

  I have heard of this problem it can be due to RFI in the shack. It is recommended to keep CAT and Audio cables as short as possible. A simple test would be to use clip on ferrite on the USB, audio and CAT cables. Hope this is of help

• 
  @burnessansell26 күн бұрын

  @@waynephillips1848 Thanks! I do have quite a bit of RFI here in the shack and plenty of ferrite cores. I'll try that first as that's the simplest explanation so far and easiest to fix barring changes to the rig or the WSJT-X software. Tnx & 73.

• 
  @WilliamBennerJr28 күн бұрын

  I found a problem that creates noise on all ICOM 7100. See the video I made here: kzread.info/dash/bejne/aHqFlqyphcvRoLg.html

• 
  @user-jk4bt1sn1rАй бұрын

  Hi friend, can you help me my icom 271 can received 143.44mhz to 153.99mhz but the transmit is only in this frequency 144-146mhz how can this transmit upper and lower of this frequency?

• 
  @waynephillips184829 күн бұрын

  Hi, quick look at the manual and the only thing I can find The manual states the frequency coverage:U.S.A version cover's 143.8 to 148.2MHz, European version 144 to 146MHz, Australian version 144 to 148MHz A no-backlash dial controls By Icoms unique rotary encoder circuit. The band edge detector and endless system provides out of band protection.

• 
  @vishalluthra7774Ай бұрын

  Can please give link where you bought parts from. Thanks

• 
  @waynephillips1848Ай бұрын

  The company was call AUTODOC, best prices i could find but delivery times!! Don't hold your breath think it was about 3 weeks to the UK, seems to be the main complaint when you look at there reviews.

• 
  @jerryzhong7217Ай бұрын

  Is JP model possible to extend frequency from 144-146 to 144-148?

• 
  @Bundproppen2 ай бұрын

  Where is part 2?

• 
  @user-tv3nu8zs3s2 ай бұрын

  Hi. Why my GX 4000D run slow?

• 
  @waynephillips18482 ай бұрын

  Hi it could be a number of factors, slipping belt, dirty fly-wheel, may simply need the mechanical parts stripping and regreasing, as the original grease dries up. Sorry its really hard to diagnose without having the unit in front of me, i would recommend a belt change and basic service of the mechanical parts.

• 
  @user-tv3nu8zs3s2 ай бұрын

  @@waynephillips1848 Thank you anyway.

• 
  @lightbulbmaniac2 ай бұрын

  I have the same unit but the right channel doesn't work at all. (Meter inactive and if you put the switch to track 3-2 and rise the volume all the way up you barely hear a tiny bit of treble.) I believe a capacitor somewhere in there has dried and shorted internally, because if I add a higher voltage to the right channel input or the right side of the head it temporarily starts working again and sounds a little distorted. Left channel is perfectly fine. Any recommendations on which components I should replace?

• 
  @waynephillips18482 ай бұрын

  Hi to be honest it sounds like your caps are coming to end of life, as you need to open up I would recommend a full electrolytic capacitor and transistor change.

• 
  @sleeve86512 ай бұрын

  Much easier to employ the Up/Down buttons on the microphone ! Learn to use the rotary switch sparingly ! 👍😉

• 
  @herby42152 ай бұрын

  I had one of these I sold it

• 
  @p--n2 ай бұрын

  Did you refit or replace the metal shield on the wishbone?

• 
  @waynephillips18482 ай бұрын

  Hi, if you mean the small metal plate next to the Disk brake that drops over the pivot, think is a heat and dust shield, mine were not to rusty so i used the originals.

• 
  @p--n2 ай бұрын

  @@waynephillips1848 thank you! Yes thats the one. Most videos I've seen don't show them being refitted

• 
  @p--n2 ай бұрын

  Theres a well documented rattle that comes from the strut itself

• 
  @waynephillips18482 ай бұрын

  @@p--n Hi, I changed every thing as per video on both sides, wish i had documented the other side, top suspension bearing had totally corroded away and a few bearing had dropped out, cluck Noise totally gone after replacement, i brought a impact gun when doing the other side, halved the time and effort needed. Bottom wish bone is a pain to fit and locate the pivot by the brake disk, i ended up using a hydraulic jack and light taps with a hammer.

• 
  @leojosedacosta70572 ай бұрын

  Eu precisava de um desses para um bom som mas como eu não posso comprar fico só assistindo ok

• 
  @waynephillips18482 ай бұрын

  Hi, thanks for watching, i strongly believe "Share the Knowledge"

• 
  @bussi78592 ай бұрын

  You really should stay of mytube with your crap videos.

• 
  @dr_ned_flanders2 ай бұрын

  I love the frequency response graphs on the speakers. No scale or axes labels. A real "mug's eyeful".

• 
  @waynephillips18482 ай бұрын

  best of the 1980's, Cant wait to open this 8060 to have a look at the cross over! Part 2 coming soon

• 
  @oxfamshop3 ай бұрын

  The Sharp version of that sort of thing was not without it issues but was a lot better

• 
  @waynephillips18482 ай бұрын

  Agree, check out my other videos, currently working on a Sharp VZ-2500e, still 90% plastic but the build quality miles ahead of the amstrad.

• 
  @iDiyYoyo-lf4so3 ай бұрын

  Audio hi-end , i like it

• 
  @waynephillips18483 ай бұрын

  To gain access to the turntable, lift the center silver logo, it is glued down!!, remove the circlip. the belt folded length 21cm, width 5mm and thickness 0.7mm

• 
  @Globalinfo786453 ай бұрын

  brother I have same setro system but cannot play please help me to guide

• 
  @waynephillips18483 ай бұрын

  Hi, awaiting on new belts, will publish part two as soon as the belts arrive, if the vinyl is not playing check the button on the bottom of the unit is operating, this needs to be depressed when the unit is upright, safety feature of the unit. Hope this is of help

• 
  @Globalinfo786453 ай бұрын

  @@waynephillips1848 thanx a lot but can you share me your any contact plateform for information?

• 
  @Globalinfo786453 ай бұрын

  @@waynephillips1848 please M very greatful to you

• 
  @tomasw69853 ай бұрын

  Good video. I was about to buy one but if you can't run the desoldering gun and iron at the same time it's not worth it to me. It's like driving your car. If you have to wait two minutes to go from drive to reverse and another two minutes to drive it doesnt seem practical if you are doing a lot of component replacements.

• 
  @waynephillips18483 ай бұрын

  I previously had a pace unit, that you could run both at the same time, but it cost over 4 the cost of this unit, all i needed was a dedicated desolder unit, the soldering iron was a bonus for me.

• 
  @josetomasgalveziniguez19403 ай бұрын

  I have put an emulator on my Gs 1250 and always leave it open. 

• 
  @Globalinfo786453 ай бұрын

  i need your help

• 
  @Globalinfo786453 ай бұрын

  hay bro

• 
  @Globalinfo786453 ай бұрын

  please tell me ?

• 
  @Globalinfo786453 ай бұрын

  hay bro

• 
  @anthonyyeo72393 ай бұрын

  Mine switches off when doing class one teat Any ideas where to start

• 
  @bobicmukasakato47353 ай бұрын

  How can l get this amplifier for my speaker

• 
  @tonyf64673 ай бұрын

  Very instructive but is there a way to bring in some treble and not so much bass? Hard to understand.

• 
  @playstation2bigs3 ай бұрын

  @ 4:40 what the use of that black thin rubber at the right side

• 
  @jgarcia72513 ай бұрын

  its to change the tips while the tip is still hot. But I wouldn't recommended it unless it's good quality.

• 
  @Chris-Brown-3 ай бұрын

  Thought Siglent was 50V DC

• 
  @2E0ILFhamradio4 ай бұрын

  i have the ftdx10 with the at0 pro 2 i have to put rf to tune ant ideas why?

• 
  @Pollys13a4 ай бұрын

  I'm thinking of getting a Creworks lathe. Have you used yours very much, have you had any problems with it? Thanks.

• 
  @waynephillips18484 ай бұрын

  Hi, i have used the lathe for quite a few hours, I would say the only problem i have come across is the Variable speed control knob, intermittently when turned to 0 RPM the chuck still rotates very slowly, a quick rotate up then back to 0 seems to cure the problem. hope this helps.

• 
  @beniaminopillitu56554 ай бұрын

  Hi, good job, I am doing the transistors replacement in my GX 4000. Not doing the capacitors at the moment because I heard the old ones are usually good.. Did you find any to be faulty when you replaced them?

• 
  @waynephillips18484 ай бұрын

  Hi, If you have taken the effort to take the unit apart i would defiantly do the caps, to be honest i never tested the caps i removed, the caps dry out over time, might save you having to do the job twice.

• 
  @user-me4kk9co4n4 ай бұрын

  Hi Wayne, great videos for doing this work. Is there any chance of getting a full buy list along with the drawings required to install? Would be very helpful to have the latest and most correct tasks etc all in one place. Along with the settings.

• 
  @waynephillips18484 ай бұрын

  Hi, start of video 6 and end part of video 5 hopefully will give you the information you need, I have since sold the Duet and moved on to modifying CNC routers, although the electronic's for the Duet worked perfectly I think the setting in mach3 for the motor tuning and port setting would benefit from a little tweaking based on the PC you are using.

• 
  @amsterdamas15 ай бұрын

  Hello there, nice video. Recently I also got cheap 2nd hand. Managed to repair it, but it seems its firmware is wiped and needs reuploading .syx firmware file. Maybe you, by any chance have it?

• 
  @ivancastillo1795 ай бұрын

  Could you pin out the pins I wanna see if this would work with a different model.

• 
  @2nostromo5 ай бұрын

  what did you settle on?

• 
  @txmg095 ай бұрын

  Nicely done.

• 
  @micheleflorio99965 ай бұрын

  Non credo tutti transistors danneggiati

• 
  @waynephillips18486 ай бұрын

  Just as a follow up to get the machine accurate in X,Y,Z, in Menu Motor Tuning i set as following Steps per - X,Y,Z = 400 Velocity - X,Y =2000, Z =700 Acceleration - X,Y =200, Z=150 Step Pulse = 15 Direction Pulse =1

• 
  @johnwood4066 ай бұрын

  Thanks for sharing looking at one right now to make clock parts.

• 
  @markedwards19006 ай бұрын

  The table saw and lathe are probably pulling 5.5 hp so the grinder overloads it

• 
  @goddlediddles6 ай бұрын

  I could understand you if you stopped mumbling.