I remember doing some research and thought it was previously Hitachi by the green casing. Built some one the best furniture with the tightest angles with a hitachi chop saw purchased at costco back in c1998. So I bought this. sale at local supplier but locating one in stock in So. Cal for same day pick-up was difficult. One available. Got it. The loose parts and the nuts and bolts could be better differentiated in the instructions as I lost the bag of bolts when unboxing...Actually was wearing my rings as well, got frustrated and took them off when I couldnt find the nuts and bolts. But once found, everything was put together in a snap. I didn't turn the saw upside down because....it will never be upside down and I didnt want some intial assembly to cause any unknown pre-stress on what may be an adjustment later/or many future adjustments because i stuck the saw upside down to put it together. If you can lift it out of your car you can assemble it wheels and handle first and then drop down the saw, angle the legs to get better access to the bold head that needs to be secured. I assume they specify it being upside-down so you don't inadvertently cut yourself or something. When I first thought the bolts were gone I was very pleased with the frame for using on the ground or table. First time I ever saw this rip fence design was on a Dewalt back in the early 2000s. Seems everyone does it similar now. I got an ol 1972 craftsman contractor saw that this is going to compliment...not replace. Great video. Great tool....Hope you recouped savings since you were a first adopter years ago. Cheers!
@jeff1806Ай бұрын
Can the riving knife be removed or pushed below table height so you can do dado cuts with the ripping blade? Can this saw handle a dado blade (how wide) and can you purchase different table inserts for dado and zero clearance?
@JBF_75Ай бұрын
The riving knife does have a setting that will go below blade height for dado cuts with a ripping blade. I don't own a dado stack, so can't comment there. And from what I have found, you cannot buy inserts for this table saw.
@jeff1806Ай бұрын
@@JBF_75 Thanks. Interesting to know about additional inserts. They say it will do almost a 3/4" wide dado cut. But if you can't purchase an insert for it, what good is it. I suppose you could try and make one.
@dosidos9944Ай бұрын
Funny
@marioortiz24752 ай бұрын
A question brother, how has the table saw served you today? And one question: I just bought mine, but I notice that when I press the brake button there is some sparking momentarily inside the engine. Does this also happen to you, or is it a factory defect?
@kaf23034 ай бұрын
Try turning the fans the other way, so the heated air can rise naturally and be drawn through the wood and into the bottom of the heating area.
@brentwpg14 ай бұрын
Holy Crap you're strong!
@tarunjani92994 ай бұрын
How much time does it take to dry lumber ?
@JLang-bn3hs5 ай бұрын
Glad that when you voted, everyone agreed on “down hill.”
@tee-in-pdx23445 ай бұрын
So it’s possible to turn a door into a desk. But my goodness the work. That must of took a long time. So my issue is I have a folding hollow door that used to be in my laundry room and I wanna make it into a desk. Thanks because now I know what not to do!! But any tips I’m glad to receive them.
@brianconnor6265 ай бұрын
Would the solar panel work inside the kiln?
@pleappleappleap5 ай бұрын
Do use the jobsite saw for actual woodworking?
@JBF_75Ай бұрын
I've had this saw for 5 years now. In that time I have used it for multiple reasons, but the past 2-3 years have been for woodworking. In that time I have built numerous jigs and sleds to do the more intricate work, and its still performing well. Fence is starting to age out, so came on YT looking for options.
@pleappleappleap5 ай бұрын
Instead of tarp, how about roofing fabric?
@pleappleappleap5 ай бұрын
How awesome would this be in cedar?
@pleappleappleap5 ай бұрын
Is it actual tin, or is it steel?
@ronaldmikelee70266 ай бұрын
Has he never done this before? How heavy did he think they would be
@gregmislick11176 ай бұрын
You need a winch and lots of extra lengths of winch line to bring those down… maybe even a sled
@milleradam986 ай бұрын
How is it holding up? I've read a lot of reviews people say the fence doesn't stay square is that your experience?
@JBF_75Ай бұрын
I've had it for about 5 years now. Just noticed that the fence has moved a little. Might need to replace the fence but looking at other options too.
@golsaber7 ай бұрын
Great review. But if you need your fingers intact, remove all your accessories when working with rotary power tools. Just my 2 cents.
@pamtnman15157 ай бұрын
Shipping container 👍
@Hansaman587 ай бұрын
Bought one yesterday. Was planning to buy the 36V version but would have to buy battery and charger or the AC adapter which significantly increases an already high price. Got my corded version for $449. I own other Metabo tools (Hitachi when purchased) and they are excellent.
@prasmussen82937 ай бұрын
Have had mine for a few years and am very happy with it. The original blade did not last long and I replaced it with a Diablo general purpose blade and a DeWalt fine cut. Both work great. Learning how to do different cuts and more effectively use the miter gauge. I did polish the table surface and that makes a huge difference.
@paulm4456Ай бұрын
Hey what polish did you use? Thanks.
@xIMT23x7 ай бұрын
Howd the inlet situation turn out. I wouldnt think it would matter since your inlets should actually come in at the bottom and the top ones should be exhaust since heat rises. It should work like a charcoal grill
@HeartToHomeWoodworking7 ай бұрын
Thanks for the comment! Here are the plans: vtechworks.lib.vt.edu/server/api/core/bitstreams/64394f45-484b-4267-9154-ed10e7d82c5b/content
@MarkSulky-vj8sz7 ай бұрын
Pushing the air around from the top is an inefficient and probably ineffective circulation method. Pull cooler air from a location close to the bottom up to the top with ducting like flex duct to warm the stack more evenly. May only require one fan. Right now you are just blowing around hot air in place.
@HeartToHomeWoodworking7 ай бұрын
Hey Mark, I appreciate the feedback. I’ve just built it as per the recommendations from here: vtechworks.lib.vt.edu/server/api/core/bitstreams/64394f45-484b-4267-9154-ed10e7d82c5b/content You should design something and build it! I’m quite curious to see how your design would work.
@777PLove8 ай бұрын
nice job man
@777PLove8 ай бұрын
got a big close too big as the first cap you cut had too raft it down through a few good rapids with my border collie riding that burl like a proud girl my helper met me at take out when we got it home we through a burl party 4 grown men could not pick it up takes grit and dertermaniton too move dense burl on your own awesome job love the rig on your trailer I could use one of those. Iy is so crazy why loggers leave the best part behind. also I love the low down by the root wood as well nice vid man
@vincevince74828 ай бұрын
Ironically I upgraded from the exact same table saw. Mine didn’t crap out at least. I came to see how to use the fence. I was at a loss. I didn’t realize you just need to tug it. Seemed too tight like there was a release or something and was afraid to break it. Thanks for showing how to adjust and check the blade for square etc. I’m looking forward to having an accurate measure right on the saw instead of having to use the measuring tape for everything.
@user-qg4yg2um7g9 ай бұрын
I bought the same saw , But when ever I I try to rip , the fence moves
@user-qg4yg2um7g9 ай бұрын
Never mentioned the locking lever on the fence. Damm you I've seen all the videos on the hitachi table saw and that lever is never even mentioned..
@kensmith89979 ай бұрын
My kiln does expel air out the bottom vents, I have the gap between the fans and back of the kiln small, I also use rubber roofing as the tarp, at first don't open vents much to limit drying fast, as wood gets below 10%, open bottom vents More, also on solar panels, use a buck converter to control voltage from solar panels, as to high of voltage can damage fans if panels can make more than 14v
@Peter-od7op5 ай бұрын
So heat goes down
@kensmith89975 ай бұрын
Yes, the fans move the air over the top of the stack, and force air through the stack, some air is expelled out the bottom vents, some is recirculated
@2fuzy9 ай бұрын
I have the same saw and I love the saw it always surprised that they did not design a place to store the miter gauge ...that I have hardly ever used
@hjeffwallace6 ай бұрын
There is miter storage behind the cord wrap. Look for 2 black rectangles about 1 inch.
@JBF_75Ай бұрын
@@hjeffwallace @2fuzy its there, but its crap. I installed a larger fence for the miter gauge, and drop it permanently into the "handle" on the lower left by the wheels. But I also have a crosscut sled that I use more often.
@patminister441410 ай бұрын
Thanks nice set of 5 vids
@patminister441410 ай бұрын
Interesting
@theshoreys474110 ай бұрын
So how did the kiln work out? What kind of changes did you make? I’m thinking about making one and I live up in northern Maine, USA.
@dragonlotion1789 Жыл бұрын
Anyone else having a problem with the Arbor Nut coming loose due to the stop break when turning off the saw?
@qelasta Жыл бұрын
I learn dog dont help much with stress situation😂
@LeeADKMOBILEMILLING Жыл бұрын
Also it was really good to see someone who's not afraid to melt in the rain
@LeeADKMOBILEMILLING Жыл бұрын
Could I get the dimensions of your solar calm please
@d.k.1394 Жыл бұрын
I own it...works great with a new cmt italian blade
@d.k.1394 Жыл бұрын
Great review
@rosethroop8410 Жыл бұрын
Just came across your video on your solar kiln .Good video . Just wondering what product did you use to put on your floor. I can not find the product VIrginia Tech used. It is called Leak Stopper .I am planning on building a solar kiln . I live in Pembroke Ontario.
@HeartToHomeWoodworking Жыл бұрын
Heyo! I just painted it black with exterior paint. Didn’t bother using any leak stopper or anything
@HeartToHomeWoodworking Жыл бұрын
Heyo! I just painted it with black exterior paint. Didn’t bother using any leak stopper or anything. No issues with it so far!
@rosethroop8410 Жыл бұрын
@@HeartToHomeWoodworking Thanks
@pleappleappleap5 ай бұрын
You could just get a can of roll-on Flex Seal. It's a bit pricey, but seals up real well.
@christinareed640 Жыл бұрын
Thank you for the how to video man 👍🏼
@ericswild Жыл бұрын
I had the same older saw and just upgraded to the same saw..used though. Had a broken fence lock lever $10 so the guy gave it to me for $40 with stand, rip blade, dado throat option...
@Crunchy_ass_dad Жыл бұрын
Damn, it is May 3rd!
@nitrousblast1 Жыл бұрын
Are the fir or pine burls? I’ve never seen the inside of those. Maybe one video show one cut up?? Thanks
@airsoftjunkie5592 Жыл бұрын
I'd recommend maybe some heavy duty poly instead of the tarp? Still learning on my own kiln myself (indoor) But I've just been using cheap poly, with the expectation it gets replaced each time. Been thinking of trying heavy duty, and reusing it...
@lucianhodor9585 Жыл бұрын
You paid a lot for your saw ! Amazon has it for $ 450. 00 right now !!!
@howard5567 Жыл бұрын
Well you have done a good job on your start-up. You have some fine tuning to go. First you need to find a good heaver tarp that will fit tight from side wall to wall. So it does not lay on top of your stacks, for best air flow. Over & thru your stacks. Myself I stay-away from metal roofing & use a 90 lb black roll roofing. Easier to patch.
@timbervisions Жыл бұрын
I like how your kiln turned out. Gave me some good things to think about when I build one for myself. Subbed as well as I know the grind it is to get to the magic 1k. Keep up the great work!
@reislogan40 Жыл бұрын
What is the table height on that?
@d.k.1394 Жыл бұрын
About 900mm
@tomnewberry5440 Жыл бұрын
Thanks for a well thought out & well presented series on building a solar kiln. I've watched a lot of folks's videos on this topic. Some (like yours) are very informative, and others have value in showing me how to NOT do it. I am just up & running with my new mill (considerably more than $4K) and will be building one of these at the ranch & possibly at my place in rural area just outside of Portland.
Пікірлер
I remember doing some research and thought it was previously Hitachi by the green casing. Built some one the best furniture with the tightest angles with a hitachi chop saw purchased at costco back in c1998. So I bought this. sale at local supplier but locating one in stock in So. Cal for same day pick-up was difficult. One available. Got it. The loose parts and the nuts and bolts could be better differentiated in the instructions as I lost the bag of bolts when unboxing...Actually was wearing my rings as well, got frustrated and took them off when I couldnt find the nuts and bolts. But once found, everything was put together in a snap. I didn't turn the saw upside down because....it will never be upside down and I didnt want some intial assembly to cause any unknown pre-stress on what may be an adjustment later/or many future adjustments because i stuck the saw upside down to put it together. If you can lift it out of your car you can assemble it wheels and handle first and then drop down the saw, angle the legs to get better access to the bold head that needs to be secured. I assume they specify it being upside-down so you don't inadvertently cut yourself or something. When I first thought the bolts were gone I was very pleased with the frame for using on the ground or table. First time I ever saw this rip fence design was on a Dewalt back in the early 2000s. Seems everyone does it similar now. I got an ol 1972 craftsman contractor saw that this is going to compliment...not replace. Great video. Great tool....Hope you recouped savings since you were a first adopter years ago. Cheers!
Can the riving knife be removed or pushed below table height so you can do dado cuts with the ripping blade? Can this saw handle a dado blade (how wide) and can you purchase different table inserts for dado and zero clearance?
The riving knife does have a setting that will go below blade height for dado cuts with a ripping blade. I don't own a dado stack, so can't comment there. And from what I have found, you cannot buy inserts for this table saw.
@@JBF_75 Thanks. Interesting to know about additional inserts. They say it will do almost a 3/4" wide dado cut. But if you can't purchase an insert for it, what good is it. I suppose you could try and make one.
Funny
A question brother, how has the table saw served you today? And one question: I just bought mine, but I notice that when I press the brake button there is some sparking momentarily inside the engine. Does this also happen to you, or is it a factory defect?
Try turning the fans the other way, so the heated air can rise naturally and be drawn through the wood and into the bottom of the heating area.
Holy Crap you're strong!
How much time does it take to dry lumber ?
Glad that when you voted, everyone agreed on “down hill.”
So it’s possible to turn a door into a desk. But my goodness the work. That must of took a long time. So my issue is I have a folding hollow door that used to be in my laundry room and I wanna make it into a desk. Thanks because now I know what not to do!! But any tips I’m glad to receive them.
Would the solar panel work inside the kiln?
Do use the jobsite saw for actual woodworking?
I've had this saw for 5 years now. In that time I have used it for multiple reasons, but the past 2-3 years have been for woodworking. In that time I have built numerous jigs and sleds to do the more intricate work, and its still performing well. Fence is starting to age out, so came on YT looking for options.
Instead of tarp, how about roofing fabric?
How awesome would this be in cedar?
Is it actual tin, or is it steel?
Has he never done this before? How heavy did he think they would be
You need a winch and lots of extra lengths of winch line to bring those down… maybe even a sled
How is it holding up? I've read a lot of reviews people say the fence doesn't stay square is that your experience?
I've had it for about 5 years now. Just noticed that the fence has moved a little. Might need to replace the fence but looking at other options too.
Great review. But if you need your fingers intact, remove all your accessories when working with rotary power tools. Just my 2 cents.
Shipping container 👍
Bought one yesterday. Was planning to buy the 36V version but would have to buy battery and charger or the AC adapter which significantly increases an already high price. Got my corded version for $449. I own other Metabo tools (Hitachi when purchased) and they are excellent.
Have had mine for a few years and am very happy with it. The original blade did not last long and I replaced it with a Diablo general purpose blade and a DeWalt fine cut. Both work great. Learning how to do different cuts and more effectively use the miter gauge. I did polish the table surface and that makes a huge difference.
Hey what polish did you use? Thanks.
Howd the inlet situation turn out. I wouldnt think it would matter since your inlets should actually come in at the bottom and the top ones should be exhaust since heat rises. It should work like a charcoal grill
Thanks for the comment! Here are the plans: vtechworks.lib.vt.edu/server/api/core/bitstreams/64394f45-484b-4267-9154-ed10e7d82c5b/content
Pushing the air around from the top is an inefficient and probably ineffective circulation method. Pull cooler air from a location close to the bottom up to the top with ducting like flex duct to warm the stack more evenly. May only require one fan. Right now you are just blowing around hot air in place.
Hey Mark, I appreciate the feedback. I’ve just built it as per the recommendations from here: vtechworks.lib.vt.edu/server/api/core/bitstreams/64394f45-484b-4267-9154-ed10e7d82c5b/content You should design something and build it! I’m quite curious to see how your design would work.
nice job man
got a big close too big as the first cap you cut had too raft it down through a few good rapids with my border collie riding that burl like a proud girl my helper met me at take out when we got it home we through a burl party 4 grown men could not pick it up takes grit and dertermaniton too move dense burl on your own awesome job love the rig on your trailer I could use one of those. Iy is so crazy why loggers leave the best part behind. also I love the low down by the root wood as well nice vid man
Ironically I upgraded from the exact same table saw. Mine didn’t crap out at least. I came to see how to use the fence. I was at a loss. I didn’t realize you just need to tug it. Seemed too tight like there was a release or something and was afraid to break it. Thanks for showing how to adjust and check the blade for square etc. I’m looking forward to having an accurate measure right on the saw instead of having to use the measuring tape for everything.
I bought the same saw , But when ever I I try to rip , the fence moves
Never mentioned the locking lever on the fence. Damm you I've seen all the videos on the hitachi table saw and that lever is never even mentioned..
My kiln does expel air out the bottom vents, I have the gap between the fans and back of the kiln small, I also use rubber roofing as the tarp, at first don't open vents much to limit drying fast, as wood gets below 10%, open bottom vents More, also on solar panels, use a buck converter to control voltage from solar panels, as to high of voltage can damage fans if panels can make more than 14v
So heat goes down
Yes, the fans move the air over the top of the stack, and force air through the stack, some air is expelled out the bottom vents, some is recirculated
I have the same saw and I love the saw it always surprised that they did not design a place to store the miter gauge ...that I have hardly ever used
There is miter storage behind the cord wrap. Look for 2 black rectangles about 1 inch.
@@hjeffwallace @2fuzy its there, but its crap. I installed a larger fence for the miter gauge, and drop it permanently into the "handle" on the lower left by the wheels. But I also have a crosscut sled that I use more often.
Thanks nice set of 5 vids
Interesting
So how did the kiln work out? What kind of changes did you make? I’m thinking about making one and I live up in northern Maine, USA.
Anyone else having a problem with the Arbor Nut coming loose due to the stop break when turning off the saw?
I learn dog dont help much with stress situation😂
Also it was really good to see someone who's not afraid to melt in the rain
Could I get the dimensions of your solar calm please
I own it...works great with a new cmt italian blade
Great review
Just came across your video on your solar kiln .Good video . Just wondering what product did you use to put on your floor. I can not find the product VIrginia Tech used. It is called Leak Stopper .I am planning on building a solar kiln . I live in Pembroke Ontario.
Heyo! I just painted it black with exterior paint. Didn’t bother using any leak stopper or anything
Heyo! I just painted it with black exterior paint. Didn’t bother using any leak stopper or anything. No issues with it so far!
@@HeartToHomeWoodworking Thanks
You could just get a can of roll-on Flex Seal. It's a bit pricey, but seals up real well.
Thank you for the how to video man 👍🏼
I had the same older saw and just upgraded to the same saw..used though. Had a broken fence lock lever $10 so the guy gave it to me for $40 with stand, rip blade, dado throat option...
Damn, it is May 3rd!
Are the fir or pine burls? I’ve never seen the inside of those. Maybe one video show one cut up?? Thanks
I'd recommend maybe some heavy duty poly instead of the tarp? Still learning on my own kiln myself (indoor) But I've just been using cheap poly, with the expectation it gets replaced each time. Been thinking of trying heavy duty, and reusing it...
You paid a lot for your saw ! Amazon has it for $ 450. 00 right now !!!
Well you have done a good job on your start-up. You have some fine tuning to go. First you need to find a good heaver tarp that will fit tight from side wall to wall. So it does not lay on top of your stacks, for best air flow. Over & thru your stacks. Myself I stay-away from metal roofing & use a 90 lb black roll roofing. Easier to patch.
I like how your kiln turned out. Gave me some good things to think about when I build one for myself. Subbed as well as I know the grind it is to get to the magic 1k. Keep up the great work!
What is the table height on that?
About 900mm
Thanks for a well thought out & well presented series on building a solar kiln. I've watched a lot of folks's videos on this topic. Some (like yours) are very informative, and others have value in showing me how to NOT do it. I am just up & running with my new mill (considerably more than $4K) and will be building one of these at the ranch & possibly at my place in rural area just outside of Portland.