Good job. I am about to do mine as the mechanic quoted me $900 for all 3. Sadly its not covered under warranty.
@cormar7724 күн бұрын
Excellent work, simple and plain. I'll look up the torque specs. Very nice!
@TeachDIY16 күн бұрын
Torque specs at 5:16
@ollyk2228 күн бұрын
Which toolset do you use to remove/replace the bearing?
@TeachDIY26 күн бұрын
Gen 2, wheel bearing tool. From memory, I think it's an 82mm, but check yourself before you buy.
@collinadeolu5721Ай бұрын
What are the torque specifications?
@miles_5555Ай бұрын
They’re at 5:17
@collinadeolu5721Ай бұрын
@miles_5555 thanks man..much appreciated 🙏🏾
@BlakeCDSАй бұрын
Nice job I need to do this on my car, what are those KYB K flex springs like?
@TeachDIY26 күн бұрын
They are good. Maybe a tad stiffer than oem, but still comfortable.
@reinerzufall7487Ай бұрын
Good Job man
@bambiwinner7858Ай бұрын
I changed my 4 injectors because jerking motor and fault code with injector around 2000rev/min. You need to find a set without 3 number on the body of injector because it's bad version (for 2nd hand) for new one normally it's work because they change it. Disconnect the battery for at least 15 to 30 minutes. (PCM was update) After installation, you need to have to relearn Knock with Forscan. After start motor and stay 2min with slow engine (normally around 900rev/ min. And 1min at 1200-1500rev/min. After go to drive car for 50km till 200km for learning PCM new values. And if it's not working, change correction factor in Forscan (it exist 3 possibly '4'-'5'-'6'), relearn knock with Forscan. After unplug battery for 15-30min. After start motor normally and wait 2 min at 900rev/min and 1min at 1200-1500rev/min And go for drive.
@tomashalandrumsАй бұрын
Just broke the same arm and found yr vid very helpful. I did the same steps and now bird can fly again! Thank you
@TeachDIYАй бұрын
Do order a new arm, but this should keep you flying until the new one arrives.
@374psalmАй бұрын
How much would this cost at a garage? Rough price?
@TeachDIYАй бұрын
Anything between £170 to £300. I spent £45 on the hub and £55 on the tool. Since then, I have used the tool once more, so the second time, I only spent about £45 for the bearing. You can get cheaper bearings, but I am not sure I would trust them.
@374psalmАй бұрын
@@TeachDIY thanks...aye it cost me £150 ...supplied and fitted
@kristian3aАй бұрын
7:51 what are you doing here, after you removed the bolt, and before you move the drive shaft?
@TeachDIYАй бұрын
I am using an air hammer to unseat the drive shaft from the wheel hub.
@AnaGrana-pq3nt2 ай бұрын
quisiera saber que ganas engañando a la gente todo mentira desde el primer momento que sacas el clip del sobrante pues sale hacia atras no para delante y terminas el video igual sino programas el inyector nuevo no izistes nada.
@TeachDIYАй бұрын
¿Qué ganó? Nada. Yo no hago ningún dinero con este canal. Pero este es un comentario estúpido. El clip puede entrar por delante o atrás, como lo has visto en este video. Y estos inyectores en el motor Lynx 1.8 TDCI Duratorq no necesitan ser reprogramados. Deberias informarte un poco antes de lanzar acusaciones contra personas. Yo podía solamente borrar tu comentario, pero lo voy a dejar aqui, para que la gente vea la estupides de algunas personas.
@UnknownPerson-cl9di2 ай бұрын
My anxiety hasn't been worse in my life than watching this video
@rupedog2 ай бұрын
Hope u remembered to recover you locking wheel nut key of the wheel before u drove it! V useful vid
@hafiziehamzah16642 ай бұрын
Same for ford fiesta ecoboost 1.0?
@TeachDIYАй бұрын
I am not sure. Check the location of the sensor port. Do remember, there are two sensors associated with this system., one for sensing the air flow temp and one for the actual temperature inside the cabin. This one is for the temperature inside the cabin.
@user-vr5fr6mv4p3 ай бұрын
Hiya, do the injectors correlate to the cylinders, ie cyl 1 is injector 1, etc? Thx
@TeachDIYАй бұрын
The injectors don't have a number per se, as you don't buy them as injector 1, etc. But yes, once installed, if you tell me that injector 1 has failed, I would understand that you are referring to the injector on cylinder 1.
@Assarkask4 ай бұрын
Hi is it the same procedure for mk3?
@Vanadeo2 ай бұрын
Similar I imagine.. They're pretty much same concept on most cars..
@patriklabic84674 ай бұрын
Hi, thank you very much for nice manual :), in about hour i go to do it on MK4 , wheelhub is still sleep in freezer, everything is prepared for this job. :) DIY 4ever :D
@jakubmarek57524 ай бұрын
does it have to be aerated?
@TeachDIYАй бұрын
I have replaced a ccouple of these injector as this engine came with the injectors series ending on 3. The only time I had to prime the system, was when I replaced the return line, but never for individual injectors.
@stalkergreg5 ай бұрын
Miért kellett cserélni? Nem lett volna elég csak megtakarítani?
@TeachDIYАй бұрын
Az Egyesült Királyságban könnyebb újat venni, mint felújítani.
@nikolairudenstein.49175 ай бұрын
Super .
@user-rd9df1vx2b5 ай бұрын
Didnt see a copper washer ??
@TeachDIYАй бұрын
4:14, it's already installed in the new injector.
@jpadilla05156 ай бұрын
Hello, what is the name of that tool you're using? In the red box?
@TeachDIYАй бұрын
Gen2 wheel hub tool. It comes in different sizes, from memory this one is 82mm, but it has been a while.
@blabla1177-r7u6 ай бұрын
Late to the game, but I got this CPU to have fun with OC and it goes 5GHz on 1.32V. Seems like I won the silicon loterry with it. Now I'm gonna delid it and do direct die watercooling on it to see what can I achieve.
@TheDutyPaid7 ай бұрын
That is that lift you have there?
@TeachDIY7 ай бұрын
That's a portable pivot car lift www.sealey.co.uk/product/5637706758/1500kg-portable-pivot-car-lift you can buy them from a few different manufacturers.
@iang46967 ай бұрын
great video saved me having to mess around booking into a garage, do you recommend changing both springs if only one has broke? also just ordering the spring or springs now do you rate the KYB highly? thanks again bud, appreciate the video
@TeachDIYАй бұрын
I didn't bother, though the other side went about a year later.
@bignasty32748 ай бұрын
You must remember to oil the forcing bolt as it preserves the threads.
@Vanadeo2 ай бұрын
Important, especially on them wicked spring compressors.. I hate those.
@TeachDIYАй бұрын
@Vanadeo Completely right. I bought a pedestal hydraulic one from amazon for about £95. Never using those stupid bolts again.
@WelshChapman8 ай бұрын
Thank you for sharing
@TeachDIY7 ай бұрын
Thanks for watching!
@tomek86010 ай бұрын
If you hear the bearing while ratating wheel by hand, they are worn as hell. Normally you hear them when wheel sre spinnig under the full load of a car. Nicely done 👍
@GlossaME11 ай бұрын
How can you check which one is gone bad? Thanks
@TeachDIYАй бұрын
I use FORScan to read faults. The engine went on limp mode a couple of times.
@fujie-web11 ай бұрын
Good job Guy ;oP Is it possible to send the scan of the user manual of the tool used (the one presented in the video) in order to clearly see the installation according to the extraction or the insertion? Thanks in advance.
@DeepBreaths33 Жыл бұрын
From the video, I saw that the old and new injectors are both Continental not Siemens. So neither Siemens nor Continental needs to be coded to the car ECM?
@TeachDIYАй бұрын
You know more than me. I know the original injectors are Siemens, what you saw in the video is what I got from the parts store and it didn't need programmed.
@MOHAMOHAism Жыл бұрын
Ni purge ni rien du tout. Et elle démarre normale !
@TeachDIYАй бұрын
C'est exact.
@SJR275 Жыл бұрын
Thanks didn't think it would be this easy actually. Probably on a note I'd replace the injectors one at a time and turn the car over so that u don't have to reprime the fuel pump because I'm lazy haha. Glad to know that these engines make a lot of ticking as normal too.
@BumbDaniel Жыл бұрын
hi nice video have a question u dont need to programing the injector in ecu
@TeachDIYАй бұрын
This particular engine does not need programing.
@edbrandt8972 Жыл бұрын
Great video. And good job of showing the new hub going into the knuckle.
@nevc3968 Жыл бұрын
Hi great video, where did you get the bearing tool from? 👍
@daviddalziel884 Жыл бұрын
Great video ! Really helped so I could have an idea to tell the garage what I thought the problem/noise would be . Unfortunately the discs were so worn they had to be replaced along with the pads so that the bearing ( just o/s) could be fitted . Thanks again for posting.
@bartoszwojciechowski5975 Жыл бұрын
I am in the middle of it, but your film helped me a lot. I was little surprised there is no circlip anywhere
@rockyfish3115 Жыл бұрын
Did you have to code these in after fitting
Жыл бұрын
mk4 front 82mm✌
@kevinthacker83499 ай бұрын
Thank you just the information I was looking for
@gilleskirch7403 Жыл бұрын
Thank you a lot for the video! Can you tell me/us the name of that special tool btw where you found it? Thank you!
@sheffielduk3428 Жыл бұрын
Did you hear any nocking because of the broke spring??
@sebastiencauvin Жыл бұрын
hi thanks for your video. One question : you have to encode the injector or not ?
@9826782494 ай бұрын
This 1.8 TDCi does not require injector coding
@ANDY-we7mr Жыл бұрын
HI MATE I HAVE A FORD FOCUS MK3 64 PLATE I HAVE SEEN THEM BEARING PULLER ON EBAY IT SAYS I NEED A 78MM PULLER IS THAT RIGHT IS YOUR 78MM CHEERS
@huseinstolar2018 Жыл бұрын
hi! I have a problem with my Ford Transit Connect 1.8 TDCi 81kw. namely, when adding gas or accelerating, the engine jerks until I let go of the gas pedal! and it happens very often. Is it the injector in question because it is quite wet from the diesel!
@tatyanamizun8216 Жыл бұрын
what engine oil does this engine like?
@sheffielduk3428 Жыл бұрын
5w 30
@stevesmall7257 Жыл бұрын
Hi I don't use this very often but like what I see. I have the same engine but in a ford galaxy mk3 1.8 2009. I have air in the System And having trouble bleeding it out have you got any help look you can give.
@SparkyVuggs Жыл бұрын
Brilliant video which showed me exactly how to use the tools I've just bought.
@Fridzel44 Жыл бұрын
did you not have to clean the seats where the injector sit in. just bit or compressed air and whack in new one ok then?
Пікірлер
Нижний рычаг гнилой, как со старого корабля 😂
Good job. I am about to do mine as the mechanic quoted me $900 for all 3. Sadly its not covered under warranty.
Excellent work, simple and plain. I'll look up the torque specs. Very nice!
Torque specs at 5:16
Which toolset do you use to remove/replace the bearing?
Gen 2, wheel bearing tool. From memory, I think it's an 82mm, but check yourself before you buy.
What are the torque specifications?
They’re at 5:17
@miles_5555 thanks man..much appreciated 🙏🏾
Nice job I need to do this on my car, what are those KYB K flex springs like?
They are good. Maybe a tad stiffer than oem, but still comfortable.
Good Job man
I changed my 4 injectors because jerking motor and fault code with injector around 2000rev/min. You need to find a set without 3 number on the body of injector because it's bad version (for 2nd hand) for new one normally it's work because they change it. Disconnect the battery for at least 15 to 30 minutes. (PCM was update) After installation, you need to have to relearn Knock with Forscan. After start motor and stay 2min with slow engine (normally around 900rev/ min. And 1min at 1200-1500rev/min. After go to drive car for 50km till 200km for learning PCM new values. And if it's not working, change correction factor in Forscan (it exist 3 possibly '4'-'5'-'6'), relearn knock with Forscan. After unplug battery for 15-30min. After start motor normally and wait 2 min at 900rev/min and 1min at 1200-1500rev/min And go for drive.
Just broke the same arm and found yr vid very helpful. I did the same steps and now bird can fly again! Thank you
Do order a new arm, but this should keep you flying until the new one arrives.
How much would this cost at a garage? Rough price?
Anything between £170 to £300. I spent £45 on the hub and £55 on the tool. Since then, I have used the tool once more, so the second time, I only spent about £45 for the bearing. You can get cheaper bearings, but I am not sure I would trust them.
@@TeachDIY thanks...aye it cost me £150 ...supplied and fitted
7:51 what are you doing here, after you removed the bolt, and before you move the drive shaft?
I am using an air hammer to unseat the drive shaft from the wheel hub.
quisiera saber que ganas engañando a la gente todo mentira desde el primer momento que sacas el clip del sobrante pues sale hacia atras no para delante y terminas el video igual sino programas el inyector nuevo no izistes nada.
¿Qué ganó? Nada. Yo no hago ningún dinero con este canal. Pero este es un comentario estúpido. El clip puede entrar por delante o atrás, como lo has visto en este video. Y estos inyectores en el motor Lynx 1.8 TDCI Duratorq no necesitan ser reprogramados. Deberias informarte un poco antes de lanzar acusaciones contra personas. Yo podía solamente borrar tu comentario, pero lo voy a dejar aqui, para que la gente vea la estupides de algunas personas.
My anxiety hasn't been worse in my life than watching this video
Hope u remembered to recover you locking wheel nut key of the wheel before u drove it! V useful vid
Same for ford fiesta ecoboost 1.0?
I am not sure. Check the location of the sensor port. Do remember, there are two sensors associated with this system., one for sensing the air flow temp and one for the actual temperature inside the cabin. This one is for the temperature inside the cabin.
Hiya, do the injectors correlate to the cylinders, ie cyl 1 is injector 1, etc? Thx
The injectors don't have a number per se, as you don't buy them as injector 1, etc. But yes, once installed, if you tell me that injector 1 has failed, I would understand that you are referring to the injector on cylinder 1.
Hi is it the same procedure for mk3?
Similar I imagine.. They're pretty much same concept on most cars..
Hi, thank you very much for nice manual :), in about hour i go to do it on MK4 , wheelhub is still sleep in freezer, everything is prepared for this job. :) DIY 4ever :D
does it have to be aerated?
I have replaced a ccouple of these injector as this engine came with the injectors series ending on 3. The only time I had to prime the system, was when I replaced the return line, but never for individual injectors.
Miért kellett cserélni? Nem lett volna elég csak megtakarítani?
Az Egyesült Királyságban könnyebb újat venni, mint felújítani.
Super .
Didnt see a copper washer ??
4:14, it's already installed in the new injector.
Hello, what is the name of that tool you're using? In the red box?
Gen2 wheel hub tool. It comes in different sizes, from memory this one is 82mm, but it has been a while.
Late to the game, but I got this CPU to have fun with OC and it goes 5GHz on 1.32V. Seems like I won the silicon loterry with it. Now I'm gonna delid it and do direct die watercooling on it to see what can I achieve.
That is that lift you have there?
That's a portable pivot car lift www.sealey.co.uk/product/5637706758/1500kg-portable-pivot-car-lift you can buy them from a few different manufacturers.
great video saved me having to mess around booking into a garage, do you recommend changing both springs if only one has broke? also just ordering the spring or springs now do you rate the KYB highly? thanks again bud, appreciate the video
I didn't bother, though the other side went about a year later.
You must remember to oil the forcing bolt as it preserves the threads.
Important, especially on them wicked spring compressors.. I hate those.
@Vanadeo Completely right. I bought a pedestal hydraulic one from amazon for about £95. Never using those stupid bolts again.
Thank you for sharing
Thanks for watching!
If you hear the bearing while ratating wheel by hand, they are worn as hell. Normally you hear them when wheel sre spinnig under the full load of a car. Nicely done 👍
How can you check which one is gone bad? Thanks
I use FORScan to read faults. The engine went on limp mode a couple of times.
Good job Guy ;oP Is it possible to send the scan of the user manual of the tool used (the one presented in the video) in order to clearly see the installation according to the extraction or the insertion? Thanks in advance.
From the video, I saw that the old and new injectors are both Continental not Siemens. So neither Siemens nor Continental needs to be coded to the car ECM?
You know more than me. I know the original injectors are Siemens, what you saw in the video is what I got from the parts store and it didn't need programmed.
Ni purge ni rien du tout. Et elle démarre normale !
C'est exact.
Thanks didn't think it would be this easy actually. Probably on a note I'd replace the injectors one at a time and turn the car over so that u don't have to reprime the fuel pump because I'm lazy haha. Glad to know that these engines make a lot of ticking as normal too.
hi nice video have a question u dont need to programing the injector in ecu
This particular engine does not need programing.
Great video. And good job of showing the new hub going into the knuckle.
Hi great video, where did you get the bearing tool from? 👍
Great video ! Really helped so I could have an idea to tell the garage what I thought the problem/noise would be . Unfortunately the discs were so worn they had to be replaced along with the pads so that the bearing ( just o/s) could be fitted . Thanks again for posting.
I am in the middle of it, but your film helped me a lot. I was little surprised there is no circlip anywhere
Did you have to code these in after fitting
mk4 front 82mm✌
Thank you just the information I was looking for
Thank you a lot for the video! Can you tell me/us the name of that special tool btw where you found it? Thank you!
Did you hear any nocking because of the broke spring??
hi thanks for your video. One question : you have to encode the injector or not ?
This 1.8 TDCi does not require injector coding
HI MATE I HAVE A FORD FOCUS MK3 64 PLATE I HAVE SEEN THEM BEARING PULLER ON EBAY IT SAYS I NEED A 78MM PULLER IS THAT RIGHT IS YOUR 78MM CHEERS
hi! I have a problem with my Ford Transit Connect 1.8 TDCi 81kw. namely, when adding gas or accelerating, the engine jerks until I let go of the gas pedal! and it happens very often. Is it the injector in question because it is quite wet from the diesel!
what engine oil does this engine like?
5w 30
Hi I don't use this very often but like what I see. I have the same engine but in a ford galaxy mk3 1.8 2009. I have air in the System And having trouble bleeding it out have you got any help look you can give.
Brilliant video which showed me exactly how to use the tools I've just bought.
did you not have to clean the seats where the injector sit in. just bit or compressed air and whack in new one ok then?