Hi Hilton, my gate crashes open. It's has a new PC board, magnets and doss centre put in. It works when setting (slow motion) but when using the remote it slams open into the open stopper. Ps battery is okay and has been checked. It is the old d5 before the evolution range. Any thoughts please?
@balugasailing10 күн бұрын
Check the wheel behide the door there is 4 screws that need to be removed, open the square plastic case and there is most likely oil inside which needs to be cleaned out
@molekocheu4221Ай бұрын
Hi Hilto,my remote just fleshes,it doesn't open or close my gate
@balugasailingАй бұрын
Replace battery
@ShaneFelix2 ай бұрын
thanks Hilton, very helpful tips
@kingm85832 ай бұрын
These gate motors have way to many issues. This is coming from a technician who works on them often.
@kabelolethale86634 ай бұрын
Please help. I get error saying "Setup fail, no end stops found"...I do have end stops and it was working fine all along
@balugasailing4 ай бұрын
Hi what motor is it , is your battery ok ?
@kabelolethale86634 ай бұрын
@balugasailing Hi. It's the centurion D5. Yup the battery is good, changed it three months ago
@balugasailing4 ай бұрын
@@kabelolethale8663, reset the limits and put something on the track before the gate closes, like a hammer or heavy object about 1meter on the track, then if the gate stops there then you know its picking it up
@bradleypetersen68714 ай бұрын
Thanks for the Video Hilton, my gate moves then stops. Then moves again and stops again. Suspect its the Dos sensor like you say. Tried reseting limits but then just moves quickly one direction then other and stops again. Doesnt move slowly to end stop and back. Ill have a go and clean the dos sensor tomorrow (Fingers crossed it will work) but thanks for the Video
@bradleypetersen68714 ай бұрын
Forgot to mention its a D3 older motor simular in your Video and did replace Battery with new one. Checked all fuses and relays latches fine. Initially thought that the Collision sensitivity is too low and tried changing to 3level where gate stops with difficulty but this also didn't help. After looking at your video I suspect the dos sensor so will open there where you said where you turn to release gate and clean dos sensor also.
@bradleypetersen68714 ай бұрын
Is there a way to test the Dos sensor ? Gate still doing the same. When programing limits it moves slightly stops then goes back slightly then stops again
@user-cc4lb1jf1p4 ай бұрын
My gate opens but won't close. Seems like I'm the only one with that problem
@phistosmboweni14805 ай бұрын
How to fix if sceeen switches off whilst the gate open
@balugasailing5 ай бұрын
Replace battery
@richardvasquez1485 ай бұрын
The ugliest truck I ever saw 🤮
@GentrysGlossMobileDetailing5 ай бұрын
This hurts my brain
@balugasailing5 ай бұрын
Your brain will hurt even more when you scrubbing the underside of a boat by hand for hours 🤣👍
@GentrysGlossMobileDetailing5 ай бұрын
Wouldn't be under water with a tool not made for underwater use that runs on lithium yes it may be good now but one time and you'll regret it
@user-el9wi5cz4n6 ай бұрын
Hi Hilton. Whst would be the reason the gate just randomly open?
@balugasailing5 ай бұрын
Hi when you programmed your gate motor your neighbours may have been pressing their remotes and now they opening your gate , best to re-program your remotes
@balugasailing5 ай бұрын
Re-program your remotes , your neighbours are opening your gate with their remotes
@jozuanaude48448 ай бұрын
Morning Hilton. My Evo shows the remotes triggering the controller but does not trigger the motor to run. Already reseted to factory settings no change. Re added the remotes no change. Motor open and closes gate when using the test button. Help please. J
@syandamkhize99206 ай бұрын
Hi. If you find out the issue please tell me what it is
@harsimran18 ай бұрын
Hi, I have a D5 with the old motherboard. I am considering buying the D5 EVO motherboard to upgrade the old motherboard. Is this doable, would you happen to know if I require any other extras before I commit myself to this purchase?
@skwok431910 ай бұрын
L1 is flashing twice and no status light help please
@gilsonlaurindo502811 ай бұрын
O meu motor parou aí meio
@dogdad62 Жыл бұрын
Hii sir need help
@FuturePress1 Жыл бұрын
My D5 will close and back out open with a gap.
@mduhyx212010 ай бұрын
Mine does the same thing, did you manage to find a solution for that issue??
@FuturePress110 ай бұрын
@mduhyx2120 my intaller came back to update the software and set up the open and close limits.
@mduhyx212010 ай бұрын
@@FuturePress1 Okay I see, so it is more of a software issue? Initially I was thinking it could be the computer itself... I will found out about it, thanks a lot 👍🏾
@willemhugo920 Жыл бұрын
How do I fix it when I set the limits but the computer resets during the process? Thanks
@2tashinga Жыл бұрын
Only when Load shedding ..Gate closes 100% and then opens ..after 1 or 2 times it closes ..The battery and in side 12-+ is 12.7 volts Why ????
@2tashinga Жыл бұрын
Only when Load shedding ..Gate closes 100% and then opens ..after 1 or 2 times it closes ..The battery and in side 12-+ is 12.7 volts Why ????
@aldoafrica8403 Жыл бұрын
Hi,, My D5 Evo says Gate Drive Failure , what could be the problem a new battery was installed 4 months ago, checked all wires and fuses all ok,battery checked using multi meter
@balugasailing Жыл бұрын
Check the green plug on the right hand side of pc board, 4 wires it mounts into a plug on the pc board they can come loose or fail, take pc board into centurion they can fix or give you a service exchange
@aubreymatodlana924 Жыл бұрын
My gate is stops half way when opening and when I press remote again it closes slowly. What could be the problem?
@C20M05 Жыл бұрын
Could be that your battery is finished
@aubreymatodlana924 Жыл бұрын
The battery is new , I bought it in October
@C20M05 Жыл бұрын
@@aubreymatodlana924 check the doss sensor, my D5 motor has an older one that's a black box on the bottom right side under a green box, it was full of sand from ants once i cleared it and connected it my gate started working properly.
@luckyshezi5000 Жыл бұрын
Hi Hilton. Thank you for this video, my gate had magnet problem.
@user-wz1pb8oe8m Жыл бұрын
Great stuff, it was the disc behind the engaging wheel. Just cleaned it and relearned.
@radio598visuals4 Жыл бұрын
Hi, our gate motor opens by itself immediately after we close it. What could be the issue? Our battery still seems fine thou.
@C20M05 Жыл бұрын
I had the same problem, I set the limits again of the gate and it worked great.
@tumelomantsoe1994 Жыл бұрын
My gate keeps multiple times when i try to open it please help with a possible diagnosis
@kggaming27562 жыл бұрын
I have checked and replaced all the fuses. I have changed the battery, the charger and now the main power supply, but it keeps giving the low battery warning and stops maybe a meter after opening and everything goes off. If I connect a separate charger on the battery and let it charge that way it opens fine until the battery is to low. The diagnostic screen shows the battery at 13V and the charger at 14V. What can be the problem?
@johanleroux7140 Жыл бұрын
Hello KG did you ever find the problem with your gate motor? My gate motor is doing the same thing
@kggaming2756 Жыл бұрын
@@johanleroux7140 Unfortunately not. Something very strange is going on. The electricians that came out can't find any problems. They said I should replace the entire unit, now my supply seems to be switching polarities every week
@mabeljordaan74852 жыл бұрын
Good work, well done
@bsenau2 жыл бұрын
I changed the battery & it still opes half way or quater way
@ingonyama-giveitatry49662 жыл бұрын
Let it charge the battery
@ashleynkoe26872 жыл бұрын
my motor wont engage to manual when i rotate the dial, please help and how do i fill the oil
@kggaming27562 жыл бұрын
sounds like your disengage is stuck. Happened to me now. turn it to disengage as far as you can and use something to try and pry the gate open. should force it to disengage. should not take a lot of force as soon as the gate moves a bit turn the dial to engage again, pull on the gate a little then try to disengage it again
@rushdindesah49132 жыл бұрын
My gate keeps opening once ive just closed it?
@phumeoli2 жыл бұрын
How do I remove the cover? It is stuck. Thanks.
@thulanijohn6202 жыл бұрын
Hi Use the key to open then shake the cover left to right then lift it up. That's the only way
@phumeoli2 жыл бұрын
@@thulanijohn620 Mine has a spring-loaded pin that I have to push in, in the back that locks the cover, I found out. Thanks.
@thulanijohn6202 жыл бұрын
@@phumeoli thanks I'm happy all is good
@sciab36742 жыл бұрын
When I tried to engage motor the spine handle is off.what is going on, do you know
Пікірлер
Hi Hilton, my gate crashes open. It's has a new PC board, magnets and doss centre put in. It works when setting (slow motion) but when using the remote it slams open into the open stopper. Ps battery is okay and has been checked. It is the old d5 before the evolution range. Any thoughts please?
Check the wheel behide the door there is 4 screws that need to be removed, open the square plastic case and there is most likely oil inside which needs to be cleaned out
Hi Hilto,my remote just fleshes,it doesn't open or close my gate
Replace battery
thanks Hilton, very helpful tips
These gate motors have way to many issues. This is coming from a technician who works on them often.
Please help. I get error saying "Setup fail, no end stops found"...I do have end stops and it was working fine all along
Hi what motor is it , is your battery ok ?
@balugasailing Hi. It's the centurion D5. Yup the battery is good, changed it three months ago
@@kabelolethale8663, reset the limits and put something on the track before the gate closes, like a hammer or heavy object about 1meter on the track, then if the gate stops there then you know its picking it up
Thanks for the Video Hilton, my gate moves then stops. Then moves again and stops again. Suspect its the Dos sensor like you say. Tried reseting limits but then just moves quickly one direction then other and stops again. Doesnt move slowly to end stop and back. Ill have a go and clean the dos sensor tomorrow (Fingers crossed it will work) but thanks for the Video
Forgot to mention its a D3 older motor simular in your Video and did replace Battery with new one. Checked all fuses and relays latches fine. Initially thought that the Collision sensitivity is too low and tried changing to 3level where gate stops with difficulty but this also didn't help. After looking at your video I suspect the dos sensor so will open there where you said where you turn to release gate and clean dos sensor also.
Is there a way to test the Dos sensor ? Gate still doing the same. When programing limits it moves slightly stops then goes back slightly then stops again
My gate opens but won't close. Seems like I'm the only one with that problem
How to fix if sceeen switches off whilst the gate open
Replace battery
The ugliest truck I ever saw 🤮
This hurts my brain
Your brain will hurt even more when you scrubbing the underside of a boat by hand for hours 🤣👍
Wouldn't be under water with a tool not made for underwater use that runs on lithium yes it may be good now but one time and you'll regret it
Hi Hilton. Whst would be the reason the gate just randomly open?
Hi when you programmed your gate motor your neighbours may have been pressing their remotes and now they opening your gate , best to re-program your remotes
Re-program your remotes , your neighbours are opening your gate with their remotes
Morning Hilton. My Evo shows the remotes triggering the controller but does not trigger the motor to run. Already reseted to factory settings no change. Re added the remotes no change. Motor open and closes gate when using the test button. Help please. J
Hi. If you find out the issue please tell me what it is
Hi, I have a D5 with the old motherboard. I am considering buying the D5 EVO motherboard to upgrade the old motherboard. Is this doable, would you happen to know if I require any other extras before I commit myself to this purchase?
L1 is flashing twice and no status light help please
O meu motor parou aí meio
Hii sir need help
My D5 will close and back out open with a gap.
Mine does the same thing, did you manage to find a solution for that issue??
@mduhyx2120 my intaller came back to update the software and set up the open and close limits.
@@FuturePress1 Okay I see, so it is more of a software issue? Initially I was thinking it could be the computer itself... I will found out about it, thanks a lot 👍🏾
How do I fix it when I set the limits but the computer resets during the process? Thanks
Only when Load shedding ..Gate closes 100% and then opens ..after 1 or 2 times it closes ..The battery and in side 12-+ is 12.7 volts Why ????
Only when Load shedding ..Gate closes 100% and then opens ..after 1 or 2 times it closes ..The battery and in side 12-+ is 12.7 volts Why ????
Hi,, My D5 Evo says Gate Drive Failure , what could be the problem a new battery was installed 4 months ago, checked all wires and fuses all ok,battery checked using multi meter
Check the green plug on the right hand side of pc board, 4 wires it mounts into a plug on the pc board they can come loose or fail, take pc board into centurion they can fix or give you a service exchange
My gate is stops half way when opening and when I press remote again it closes slowly. What could be the problem?
Could be that your battery is finished
The battery is new , I bought it in October
@@aubreymatodlana924 check the doss sensor, my D5 motor has an older one that's a black box on the bottom right side under a green box, it was full of sand from ants once i cleared it and connected it my gate started working properly.
Hi Hilton. Thank you for this video, my gate had magnet problem.
Great stuff, it was the disc behind the engaging wheel. Just cleaned it and relearned.
Hi, our gate motor opens by itself immediately after we close it. What could be the issue? Our battery still seems fine thou.
I had the same problem, I set the limits again of the gate and it worked great.
My gate keeps multiple times when i try to open it please help with a possible diagnosis
I have checked and replaced all the fuses. I have changed the battery, the charger and now the main power supply, but it keeps giving the low battery warning and stops maybe a meter after opening and everything goes off. If I connect a separate charger on the battery and let it charge that way it opens fine until the battery is to low. The diagnostic screen shows the battery at 13V and the charger at 14V. What can be the problem?
Hello KG did you ever find the problem with your gate motor? My gate motor is doing the same thing
@@johanleroux7140 Unfortunately not. Something very strange is going on. The electricians that came out can't find any problems. They said I should replace the entire unit, now my supply seems to be switching polarities every week
Good work, well done
I changed the battery & it still opes half way or quater way
Let it charge the battery
my motor wont engage to manual when i rotate the dial, please help and how do i fill the oil
sounds like your disengage is stuck. Happened to me now. turn it to disengage as far as you can and use something to try and pry the gate open. should force it to disengage. should not take a lot of force as soon as the gate moves a bit turn the dial to engage again, pull on the gate a little then try to disengage it again
My gate keeps opening once ive just closed it?
How do I remove the cover? It is stuck. Thanks.
Hi Use the key to open then shake the cover left to right then lift it up. That's the only way
@@thulanijohn620 Mine has a spring-loaded pin that I have to push in, in the back that locks the cover, I found out. Thanks.
@@phumeoli thanks I'm happy all is good
When I tried to engage motor the spine handle is off.what is going on, do you know
Pls help...mine just makes a clicking sound
whats up me 078 528 7361