Пікірлер

• 
  @PAINTGREEGraffitiartstore3 күн бұрын

  what if we want to lift a big pipe reel, and the lifting points from pipe rode going thru the centre of the pipe Reel

• 
  @SimpleandBasicCalculation2 күн бұрын

  Thanks for the comment. You can drop or msg an image to my fb page so i can see clearly. So i can assist you on that particular lifting

• 
  @manuragm163012 күн бұрын

  Can anyone here tell me how the trailer grouping is done physically?

• 
  @dhairyasworldoffun403021 күн бұрын

  Please upload more videos related to Marine force calculation

• 
  @harizazhar891624 күн бұрын

  Need part 2 !!

• 
  @gousekarim290127 күн бұрын

  Hi what is accross in first method

• 
  @luisezequielleon995527 күн бұрын

  Do you have a video with 4 lifting points?

• 
  @SimpleandBasicCalculation27 күн бұрын

  Yes have, See this below link Also you can watch other video in my channel kzread.info/dash/bejne/aHqKq7CCY7nKadY.htmlsi=1mdbrlvWx4nFN8qj

• 
  @AbdulHafeezShar-zy6ly28 күн бұрын

  ok

• 
  @SimpleandBasicCalculation27 күн бұрын

  Thank you

• 
  @amithashshibu924228 күн бұрын

  Im also think it's incorrect D2 and D1 is replaced for the both equation 🤔

• 
  @SimpleandBasicCalculation27 күн бұрын

  I appreciate your comment. It is not mixed. This is just a reaction force calculation. Looking at it, the CoG is more near crane A, hence the weight in crane A is more than the crane B at 0 degree (horizontal orientation).

• 
  @jefferyhillman7851Ай бұрын

  If I'm correct crane a and crane b are backwards compared to how the equation is wrote out

• 
  @SimpleandBasicCalculation27 күн бұрын

  Yes. However, the outcome remains unchanged regardless of which part you start. Crane A to Crane B or vise versa

• 
  @ajeebashee9322Ай бұрын

  ❤

• 
  @SimpleandBasicCalculation27 күн бұрын

  Thanks

• 
  @uvaraj6328Ай бұрын

  If 8 lifting point, what will be formula for distribution of load

• 
  @SimpleandBasicCalculation27 күн бұрын

  Thanks for the comment. Let me work on it, i will make sample.

• 
  @pravinp5964Ай бұрын

  WHAT IS (m^2/t) in the permissible wind speed formula

• 
  @flochist460317 күн бұрын

  Area (m2) per mass (t)

• 
  @swamy084Ай бұрын

  how to calculate COG? 2/3 length?

• 
  @Panther-Ай бұрын

  Am not sure but I think you have the equation mixed up around @1:17 you have the calculation of crane A as D2/DT,When it should be D1/DT....D2 is for Crane B and not Crane A

• 
  @amithashshibu924228 күн бұрын

  I'm also think it's incorrect D1 and D2 will be replaced for both equations

• 
  @SimpleandBasicCalculation27 күн бұрын

  I appreciate your comment. It is not mixed. This is just a reaction force calculation. Looking at it, the CoG is more near crane A, hence the weight in crane A is more than the crane B at 0 degree (horizontal orientation).

• 
  @AHTOPАй бұрын

  super , thank you sir!

• 
  @SimpleandBasicCalculation27 күн бұрын

  You are welcome. Thanks the you like it.

• 
  @Ranveer_Singh_KahaniАй бұрын

  See..its not for lifting supervisor.

• 
  @SimpleandBasicCalculation27 күн бұрын

  Hehe

• 
  @Ranveer_Singh_Kahani27 күн бұрын

  This is....for engineers😭😭😭😭​@@SimpleandBasicCalculation

• 
  @Ranveer_Singh_Kahani25 күн бұрын

  DESIGN wasnt for lifting supervisor

• 
  @MemewVlogsАй бұрын

  This is just calculating the geometrical trimming diagral. In deep will be the beding and the hydraulic trimming diagram.

• 
  @sunnybaggu7852 ай бұрын

  Dear Sir, please share the link for detail calculation.

• 
  @muh.khalidhaekal59662 ай бұрын

  Sir can you make video about analysis lifting point, when we use 2,3,4,5,6 or 8 lifting point?

• 
  @RogelioJaimes-bz4rs2 ай бұрын

  Excelente explicacion. Muchas gracias

• 
  @SimpleandBasicCalculation27 күн бұрын

  Thank you

• 
  @yosepmargen83102 ай бұрын

  But why was the initial weight of 24 tons calculated to be 20 tons?

• 
  @civve2 ай бұрын

  Hello, Thanks for the video. Just a tip, DB is correct at 2:54 but at 2:57 you have changed it to 5534 in the calculation and that´s incorrect? Should be 5734.

• 
  @SimpleandBasicCalculation27 күн бұрын

  Yes., I appreciate your comment. I made an error in typing, thank you for noticing. However, the formula remains unchanged.

• 
  @muh.khalidhaekal59662 ай бұрын

  Sorry sir, i have a question how to choics the optimal lifting point? How do we know if we use 3,4,5 or 6 lifting point?

• 
  @muh.khalidhaekal59662 ай бұрын

  Sorry sir, i have a question how to choics the optimal lifting point? How do we know if we use 3,4,5 or 6 lifting point?

• 
  @manipmk2k12 ай бұрын

  Could you please explain the same for 8 lifting point (4 on each side)?

• 
  @JoshAlcantara-iw6zq2 ай бұрын

  If i were to use a shackle at each end of the sling, what SWL do they need to be?

• 
  @JoshAlcantara-iw6zq2 ай бұрын

  If i were to use a shackle at each end of slings, what SWL do they need to be?

• 
  @star-zt7mk2 ай бұрын

  thanks for this video

• 
  @star-zt7mk2 ай бұрын

  the video is not done

• 
  @star-zt7mk2 ай бұрын

  how

• 
  @TusharIngle-ey5xc2 ай бұрын

  Why 4 lashing point in calculation instead of 2? As only two will give resist lateral movement.

• 
  @nisarahmed-oi9uj2 ай бұрын

  Good

• 
  @VicmelDiaz3 ай бұрын

  Hi Again. I noticed that in your calculation, the weight of the cargo is not considered. I think it's important criteria that must be taking in consideration.

• 
  @Ranveer_Singh_Kahani3 ай бұрын

  Very hard

• 
  @SimpleandBasicCalculation3 ай бұрын

  Download this spreadsheet in below link for free Password: SB123@ drive.google.com/file/d/1VqcCy4Kl-7begWTQVKyzwBlXCIs3mO_k/view?usp=sharing

• 
  @luffyking41403 ай бұрын

  Thanks for your information, if you allow me there is a mistake with your calculations. The cos & sine @ 45 degrees are the same So we must always multiply the WLL with Sine not 🚫 with Cos please do your calculation with another angle and you will see. For instance with Sin 60 > horizontal angle not included 12te × Sin 60 = 10.39te And if I missed out something with your calculations please reply to me.

• 
  @user-dd6xk5bi1w3 ай бұрын

  Hello Sir. Thank you for your work. I have some questions. 1.Can you tell us, what it is the safety factor and why it need? 2.Why we find tension for each lifting points, if only 3 sling take the load? Thank you bro 🤝

• 
  @user-dd6xk5bi1w3 ай бұрын

  Hi sir. Thank you bro. But question. D2 and d2 is both same? Is this same or different? Some time you use d2 and another time D2

• 
  @user-dd6xk5bi1w3 ай бұрын

  Sir thank you for your work. It so useful for us. Can you say what is it mean LT in each formula? Total distance of load OR length of sling? Because it's the same

• 
  @SimpleandBasicCalculation3 ай бұрын

  Thank you, LT is the distance between lifting point 1 to lifting point 2.

• 
  @user-dd6xk5bi1w3 ай бұрын

  @@SimpleandBasicCalculation thank you bro

• 
  @user-dd6xk5bi1w3 ай бұрын

  Sir Thank you for your work. One question. Why in video #3 the formula in lp1 was w(d2/dt1)(d4/td2) and lp2 w(d1/td1)(d3/td2). But here another. Is they not same?

• 
  @SimpleandBasicCalculation3 ай бұрын

  Thank you for your comment, I appreciate your observation. This is just the same formula. By looking at it, the positioning of lifting points 1 and 2 in this video differs from video number 3.

• 
  @user-dd6xk5bi1w3 ай бұрын

  @@SimpleandBasicCalculation OK. Thank you 🤝

• 
  @user-dd6xk5bi1w3 ай бұрын

  So thank you Brother. Your work very useful for us. Really best chanel in the world 🤝👍

• 
  @SimpleandBasicCalculation3 ай бұрын

  Thank you so much 😀

• 
  @jasonsajadi95133 ай бұрын

  Thanks 🙏

• 
  @SimpleandBasicCalculation3 ай бұрын

  You’re welcome 😊

• 
  @user-dd6xk5bi1w3 ай бұрын

  H in tension at sling 3 is not correct. Please check it and give me answer. Please

• 
  @SimpleandBasicCalculation3 ай бұрын

  hello, thanks for the comment, i just miss type the value for “D”. that value must be 4.472 not 3.243.

• 
  @user-dd6xk5bi1w3 ай бұрын

  @@SimpleandBasicCalculation thanks for your answer 🤝

• 
  @bunnychananimeunlimited51543 ай бұрын

  Another astounding learning video, showcasing your unparalleled expertise and knowledge.

• 
  @SimpleandBasicCalculation3 ай бұрын

  Glad you enjoyed it!

• 
  @mohdmouzzamuddin12653 ай бұрын

  Excellent ..

• 
  @SimpleandBasicCalculation3 ай бұрын

  Thank you! Cheers!

• 
  @roziqahmad61113 ай бұрын

  Wow the greatest🎉. Can i get spreed sheet as like that?

• 
  @SimpleandBasicCalculation3 ай бұрын

  Thank you that you like it