Пікірлер

• 
  @HondaK203 күн бұрын

  I do it with my hand likeli then this…

• 
  @7morgey22 күн бұрын

  Hiya mate Doing a Maintance oil change on my loncin g210 was just wondering what brand oil did you use ? I know it’s a 10w-30 just want to get the best from my machine 👍

• 
  @MultiSander1986Ай бұрын

  Thanks for the video. But at what point do you need to change the clutch? Mine is still working fine but the engine takes longer to get up to speed after a big branch. Is this an engine problem or could this be a slipping clutch. I know it’s hard to tell with only this little info but maybe you have had similar issues with it. I’ve got the HC10 pro.

• 
  @clarkwilson4425Ай бұрын

  I have a 163cc loncin engine. It would only run on half choke. I've had it serviced, changed the spark plug again as it was black!!!! Then changed the carb this morning and it's still the same 😢 any idea what else it could be? I could just go buy a new engine really but am starting to try and learn a bit about the maintenance side of things .

• 
  @lewismcarthur3932 ай бұрын

  What oil goes in ?

• 
  @ciprianc709417 күн бұрын

  10W-30 0,6L

• 
  @AndreasBernhard-ex6ht3 ай бұрын

  Was koste der Sägespaltautomat

• 
  @davidgoodwin67124 ай бұрын

  Any videos on how to tighten the belt, Thanks

• 
  @patrickkohler81455 ай бұрын

  Thanks

• 
  @BAREDATA5 ай бұрын

  Link to manual in description? I feel like you're missing a link here...

• 
  @leebennett36728 ай бұрын

  What is the difference between the HC 10 and HC 10 pro .thanks

• 
  @tuulakanerva50599 ай бұрын

  Great instructions, really helpful. I have been putting off the belt change but now feel confident enought to do it.

• 
  @SLanger8910 ай бұрын

  I have the same wood chipper and i am so disappointed. Lumag installed a 20mm clutch on the 19.05mm engineshaft. This lead to worn down and damaged engineshaft and clutch. The attempt to repair was just somes grinding and a new key. So the problem is still there.

• 
  @glennlewis3002 Жыл бұрын

  Is this the same steps for the HC15 Pro

• 
  @Gdesign959 Жыл бұрын

  I have a loncin 452cc engine land it is inside a case so I don’t have good visual of the entire engine. Do you know where the fuel pet coco is on this model so I don’t have to take too much apart.

• 
  @michaelleinhos7164 Жыл бұрын

  Eine sehr geile Maschine, wer möchte die nicht.. !! Aber wer kam auf die ( sorry bescheuerte ) Idee, so eine martialische Musik DRAUFZUKNALLEN?? ES NERVT!! Originalklänge statt Musikgedudel!! Schon auf der Homepage so.. :-( Da spreche ich wohl vielen aus dem Herzen, Originalklang statt Musikgedudel bitte und echte Vorstellung!! DANKESCHÖN :-) Grüße Holzmichl ^^

• 
  @peacebeuntoyou8934 Жыл бұрын

  Where to buy HC10 Pro blades to ship to the UK?

• 
  @tomasbelica498 Жыл бұрын

  Hello, I have loncin 420cc, seem to be losing power, its fitted in jansen mgt 420 (its new). Should be strong enough to run mulch mover... any ideas?

• 
  @alijagic1975 Жыл бұрын

  what might be the cause of this engine's surging,

• 
  @applianceman6009 Жыл бұрын

  It’s a Chonda, a clone of a Honda GX160. It takes the same spark plug, oil, and air filter as a Honda.

• 
  @luishermosilla6250 Жыл бұрын

  Numero de contacto

• 
  @neilmadders5199 Жыл бұрын

  We are in the UK...

• 
  @bradalan7188 Жыл бұрын

  I have a loncin 196cc engine on my speeco auger. It won't start unless I take the air filter off and spray starting fluid in the intake. Then it won't stay running...Any suggestions?

• 
  @neilmadders5199 Жыл бұрын

  I would suggest replacing the fuel clean out the carb and replacing the airfilter

• 
  @MountainMan1985 Жыл бұрын

  @@neilmadders5199 do you know the air filter model number? I am having the same issue, even after removing the air filter and replacing the fuel

• 
  @neilmadders5199 Жыл бұрын

  @@MountainMan1985 If you have tye same issue as above you will need to clean out your carburettor.

• 
  @fulwoodphantom2 жыл бұрын

  Looks like the made in China generic ones!!

• 
  @thunder4x4882 жыл бұрын

  I have this engine on a cobra chipper how can you tell if you have put the correct amount of oil in it as I haven't got a level surface to stand it on to fill it and the chipper doesn't stand level.

• 
  @neilmadders51992 жыл бұрын

  You can either have the engine completely drained of oil and measure 600ml back in or have it on a flat surface and fill to the maximum.

• 
  @ennyaryati4232 жыл бұрын

  Apa keunggulan loncin terbaru.dgn yg terdahulu

• 
  @hrustus2 жыл бұрын

  Is it safe to use sae 30 oil for this engine

• 
  @neilmadders51992 жыл бұрын

  10W30 is recommended 😊

• 
  @davidpowell62717 ай бұрын

  I live in a tropical climate. Hence I use SAE30. I found using multigrade that the engine used oil. With SAE30 it is fine.

• 
  @dilsonscheuermann70895 ай бұрын

  It is also important to observe the API classification of the oil. So, it must be API SF or higher.

• 
  @michaelbester73122 жыл бұрын

  great video on this motor

• 
  @futbolsalacallosa2 жыл бұрын

  Cuanto aceite le cabe al motor?Gracias

• 
  @planecrazyish2 жыл бұрын

  +/- 600ml

• 
  @christophechristophe16562 жыл бұрын

  Fabrication chinoise ?

• 
  @JuanOrtiz-fc7oq2 жыл бұрын

  Comose.arma

• 
  @djavandocarlo62682 жыл бұрын

  Manda o contato aí preciso comprar uma

• 
  @jager8942 жыл бұрын

  Diese Affige Musik macht die Sache wirklich unseriös.

• 
  @Ganesh72office2 жыл бұрын

  how much price

• 
  @dickdungfork83342 жыл бұрын

  I just read that Loncin are the same as Honda engines, are they a chinese copy?

• 
  @neilmadders51992 жыл бұрын

  They are made in China like most small engines, even some Honda models in our opinion they are a comparable quality

• 
  @petteripunakuono66743 жыл бұрын

  😎😎😎💥💥💥💥💥💥💯🤠👍

• 
  @edmioz3 жыл бұрын

  not for sale in US ?

• 
  @ShawnLuciano3 жыл бұрын

  Where are you located?

• 
  @ShawnLuciano3 жыл бұрын

  We are located in New Jersey. Reach out to ForestrySales at HillCastleLeas.com

• 
  @edmioz3 жыл бұрын

  @@ShawnLuciano website is not working...

• 
  @edmioz3 жыл бұрын

  @@ShawnLuciano we are located in Charlotte NC

• 
  @kylegodon58033 жыл бұрын

  @@edmioz it is from alibaba.com and costs around $2000usd

• 
  @pavelsperlik15913 жыл бұрын

  Krám,kvalita úplně mimo

• 
  @sunilnishad57163 жыл бұрын

  MOBILE NO SEND

• 
  @barnescmx4 жыл бұрын

  Bought one of these 14 months ago, every time I cut around 30 blocks it would brake, the wheel would seize, John Hogan Lumag Ire Ltd took it back twice to fix it only the same to happen again, it has now broke again after the so called warranty expired and he will not take it back, not a friendly business at all, trouble from day one, I should have left it back immediately, stay clear folks

• 
  @bobbrooks2665 жыл бұрын

  Looks very good like to see one working before deciding but wouldn't mind one

• 
  @thegreenman48986 жыл бұрын

  seems a reasonable price, if only i had the space ;0)

• 
  @victornoble72546 жыл бұрын

  We just bought one of these machines from Lumag UK , we have now run it for 5hrs details to follow

• 
  @andrewdavies93916 жыл бұрын

  It looks really good was it worth buying their about 5,500.

• 
  @iaintelfer97346 жыл бұрын

  VICTOR NOBEL How is your lumag performing?

• 
  @lordbaby100 Жыл бұрын

  Hello Victor Noble is the maschine still working and do you use it?

• 
  @neilmadders51997 жыл бұрын

  This machine is available from the UK from Lumag distribution LTD www.lumag-gb.co.uk/shop/lumag-hc1500ew-wood-chipper/