Tbh, many people hate the Gladius, but.... outside of perhaps the headlight I think it's a very good looking bike. I might prefer the latest SV650 sliiiiightly over it, but honestly I don't see how people dogged on this bike when it came out... It's sleek, slightly curvy and stylish. And I'll be honest: this one in particular looks really good to me.
@DamiansgarageКүн бұрын
Agree, it’s definitely not for everyone but it doesn’t change the fact that it’s a fun and somewhat unique bike!
@AutumnandSummer-Foxes7 күн бұрын
I'm picking up this exact van on Saturday! Same color and everything. ❤
@Damiansgarage7 күн бұрын
Congratulations!
@user-rk8np5em8b13 күн бұрын
I have a datona but if i had one of these id go RRspeed tripple headlight and fairing
@herrcobblermachen21 күн бұрын
Cool! ty
@brettrichardson976227 күн бұрын
Were do you get those tires
@mr.ssswagg6617Ай бұрын
I Love Harbor Freight. Heres My 69" Set up! All Harbor Freight. kzread.info/dash/bejne/mH94w8iymMeTmZc.htmlsi=yngXpCSnmxUJZCYX
@nicholasmazzone3386Ай бұрын
Easy when you start the video halfway through the job 🤣🤣🤣🤣 polock for you
@andrewasher2201Ай бұрын
Nice job
@djphilly44Ай бұрын
Awesome customization. You gave me some great ideas for hacking my Kobalt Mini toolbox. Thanks.
@lolekpejo68Ай бұрын
Fajny film
@DAS-VideosАй бұрын
Now Lowes has to make some miniature tools to go in it.
@curtis20041Ай бұрын
These are rated 275 horse power
@richardcatherall20982 ай бұрын
Ordered and fitted one. Ironically same shipping damage. Planning to repaint it. For the money the difference is worth it.
@eFoobar2 ай бұрын
What did you do with the Trans Cooler lines? Pinch them off? Cap them? If you didn't, how much trans fluid did you lose after you removed them?
@user-sl2gf4zs2k2 ай бұрын
great video! Can you list all the part numbers and where did you order?
@bberg562 ай бұрын
Nice detail given the instructions come with no descriptive wording, only drawings. I could not find any information about the alignment pins anywhere else. A couple notes: I was able to remove the grommets from the door frame with my fingers - no tool required. They are somewhat flexible so once you pry one side up, keep pushing until it releases. The other note is that the orientation of the slot the key goes in needs to be such that the key goes in from the bottom. If the slot is upside down, you reach a point where you can no longer insert the key to tighten or loosen the rack. I think my rack had all mounting ends fully released allowing that piece on one mounting leg to rotate.
@Kreacher19742 ай бұрын
In America most people call your French wrench a crescent wrench
@Kreacher19742 ай бұрын
I find it funny that a lot of people say be careful of using these tools and accessories because they are cheap Chinese crap but they are forgetting that the stuff they buy from Amazon, Walmart, Target and 98% of everything everything else we buy is from China.
@Kreacher19742 ай бұрын
I haven't bought from aliexpress yet bit I do have the phillips bits and bit holders from Temu and they work perfectly.
@thomasmurphy35703 ай бұрын
PRO TIP: they sell plastic clamps at Harbor Freight and online that are specifically for clamping down line with fluid. They are basically like vise grips, except they fully are plastic (so they are less likely to tear rubber hoses) and the jaws are flat to fully seal the hose together when you ratchet them tight. I use a couple of these when changing out cooling or fueling components and usually don't lose hardly any fluid
@alexanderstefanov64743 ай бұрын
This is a great tutorial, i just got them wrapped with a piano black automotive film wrap and they look fantastic and it cost 25 EUR
@folsomflash3 ай бұрын
Why won’t mine tighten,one side does but the other side wont
@Apparition_Unknown3 ай бұрын
Great video man!
@MeatBallSplash33 ай бұрын
This is exactly what I was looking for! My 2018 is beginning to peel and was hoping for an easy fix like that! It's only peeling on one side buy im going to do both since it seems that the other side will eventually do the same
@Obelisk573 ай бұрын
Will i be able to attach Yakima bike or ski racks to these bars? How does it work?
@3vil3lvis3 ай бұрын
Use this to hold random drill bits by the drill press.
@fobbitoperator36204 ай бұрын
For $3,500, you won the damn lottery with this amazing old muscle car!
@ylberblakaj35124 ай бұрын
hi I have a mercedes sl 300 cab model year 1993. my question is, when the car is cold it starts, when it is warm it cannot be started until it has been sitting for a few hours, then you can start it again. can you the error would be very grateful🙏
@ekagemaori3 ай бұрын
Probably a position crank sensor. That’s the usual symptom of a broken position crank sensor.
@teylorherrera25345 ай бұрын
What brand is the yellow tool organizer ?
@suziwonkenobi5 ай бұрын
I just learned about the existence of these toolboxes today and I found your video. My daughter thinks she needs one of these in pink for her crafting supplies. I like your handle, latch, and the wire you added to keep the lid from opening the whole way. I see I'm going to have some DIY fun as part of the setup of her toolbox.
@Damiansgarage5 ай бұрын
I ended up giving this one to my mom for her sawing stuff it works great for that. The only issue with the pink one is that it’s usually always sold out at the store and you would have to buy it from a reseller at a marked up price.
@suziwonkenobi5 ай бұрын
@@Damiansgarage I'm in Santa Fe, NM and according to Lowe's website, pink and red are the only colors in stock near me. And there's not enough red in stock to be able to order it online and pick up in store. I'm crossing my fingers that the website is correct about the pink.
@jamijohnson37005 ай бұрын
Man I wish you could add those to my toolbox. I don't have the tools and am not handy enough to add anything, including a handle. But love all your additions to the toolbox.
@keatonbannout49075 ай бұрын
Question: I am looking to purchase a roof rack for my 2016 Prius. What brand is this one? I haven't finished the video, but based on different reviews on low noise, I wanted to purchase a Yakima or Thule. What brand is this one? Thank you!!! Also, How do you know how long the bars need to be when you're shopping?
@keatonbannout49075 ай бұрын
OEM Roof Rack. Just got that.
@Damiansgarage5 ай бұрын
Yes the OEM roof racks for the Prius are the best in my opinion because they fit perfectly and they are pretty quiet even at freeway speeds.
@dwaynthomassen42075 ай бұрын
Do you have the website where i can buy this?
@HOMELESSG0D3 ай бұрын
just google motodemic
@idealivangaming43075 ай бұрын
❤great video and explanation
@vitobelas36995 ай бұрын
You need to change that headlight 😂
@JustAnotherAsianGuy26 ай бұрын
good car
@feedusafetus79656 ай бұрын
I’ll use it for drag racing and drifting
@TienBuilds6 ай бұрын
I only watched, cause of the prime bottle .
@Damiansgarage6 ай бұрын
Jokes on you, I only put the prime bottle in the thumbnail to make people click on the video😂
@Davsoto1206 ай бұрын
This is the realist tool cart tour I’ve seen 😂 not like everyone else “flexing” their expensive power tools and rare/handy specialty tool that we “have to buy bc it’s worth it” Just a simple, cheap tool assortment of tools that get the job done! And a few that were on sale 😂(I’m guilty of buying purely bc they’re on sale)
@ApexGarage476 ай бұрын
Great video lad
@patrick42536 ай бұрын
Very thorough! Thank you!!
@thetrapdoorpig6 ай бұрын
Really beautiful bike man
@junior-hk2jt6 ай бұрын
just picked up an 09, always owned cruisers, wow these things are fast!😂
@Damiansgarage6 ай бұрын
Those are super fun to ride in the corners too you can really have some fun with it!
@keltecdan4 ай бұрын
Mine is incredibly slow to me. It’s still a great in town bike but once you get on the highway it’s a bit of a dog. I still love her though and won’t sell my first bike.
@BenzoDopamine6 ай бұрын
Do you notice any reduction in cowl shake?
@Catrik6 ай бұрын
I would be very cautious of using those fuses for anything - or anything cheap chinese crap related to any kind of safety. Louis Rossmann recently released a video where he tested top ranked Amazon fuses, and none of them worked properly. A 2 amp fused only blew at 10 amps. kzread.info/dash/bejne/dG1kwbWHfsXJn7g.html
@Damiansgarage6 ай бұрын
Yea I don’t know how I feel about those fuses either, but then, on the other hand, all the fuses you buy at automotive stores, or the retail stores are also most likely all made in China.
@Catrik6 ай бұрын
@@Damiansgarage The "Made in china"- part of the "cheap chinese crap" doesnt mean it's dangerous. When a retail store imports something for selling, they are liable, if a house or a car burns down. They also have a reputation they want to hold. So they are incentivized to research and make sure what they are selling are, if not high quality, at least safe to use. But you dont have this when you go to some random ebay/amazon/aliexpress seller with no datasheets, certifications or anything to indicate if the product is safe, or are they just trying to scam you out of your money, $1,99 at a time.
@j59626 ай бұрын
Thats not a feeler guage set.. its for thread pitch
@Damiansgarage6 ай бұрын
Good catch lol I didn’t even realize I was basically an auto pilot when ordering all this stuff.
@slowyota_rolla6 ай бұрын
Good video
@Damiansgarage6 ай бұрын
Thanks
@georgeferlazzo79367 ай бұрын
I just found your channel and subscribed. Nicely done, Brother. I hope you will do some after use videos. On well, everything works out for you. For the price you can't beat it 😅 Thank you and Merry Christmas to you and your family 😊
@d2cuadrados5107 ай бұрын
You think it's possible to replace the rails with like actual drawer rails? The stock ones kinda suck.
@Damiansgarage7 ай бұрын
It would be a pain in the butt to do it but it isn’t possible the biggest problem I believe would be finding such a short sliders
@aAbstractduck7 ай бұрын
You would need to find a slide that is about 5 inches in length (when folded) and overall thickness being less than 7mm (the gap you have on each side of the drawers) Amazon does appear to sell 5 inch slides but im not confident they will work perfectly. Perhaps you'd either have to contact a company or someone else to custom make you a set. Maybe possible to 3d print rails and get the bearing part somewhere else but im not sure the strength and durability will be any better. With that said you can try lubricating the existing slides with lithium grease. If that doesnt work you will have to remove the drawers and file down any burrs/ sharp edges present on the friction slides
@d2cuadrados5107 ай бұрын
@@aAbstractduck Yeah you're right, I'd probably need low profile slides. I'll look online to see if I can find some. In the meantime I'll try lubricating the slides with some grease. Thanks for the tip, friend!
@aAbstractduck6 ай бұрын
@@d2cuadrados510 if you find anything let me know! Quick tip on removing the drawers without causing any damage if you need to: Take a long, thin piece of metal. Put a slight bend on one side (about an inch from the end) insert it between the drawer so that it goes around the little tab preventing the drawer from coming out and then give it a pull, preferably you have one on each side. It should pop right out. I used two 0.013" feeler gages but im sure something like a hacksaw blade would also work!
Пікірлер
Tbh, many people hate the Gladius, but.... outside of perhaps the headlight I think it's a very good looking bike. I might prefer the latest SV650 sliiiiightly over it, but honestly I don't see how people dogged on this bike when it came out... It's sleek, slightly curvy and stylish. And I'll be honest: this one in particular looks really good to me.
Agree, it’s definitely not for everyone but it doesn’t change the fact that it’s a fun and somewhat unique bike!
I'm picking up this exact van on Saturday! Same color and everything. ❤
Congratulations!
I have a datona but if i had one of these id go RRspeed tripple headlight and fairing
Cool! ty
Were do you get those tires
I Love Harbor Freight. Heres My 69" Set up! All Harbor Freight. kzread.info/dash/bejne/mH94w8iymMeTmZc.htmlsi=yngXpCSnmxUJZCYX
Easy when you start the video halfway through the job 🤣🤣🤣🤣 polock for you
Nice job
Awesome customization. You gave me some great ideas for hacking my Kobalt Mini toolbox. Thanks.
Fajny film
Now Lowes has to make some miniature tools to go in it.
These are rated 275 horse power
Ordered and fitted one. Ironically same shipping damage. Planning to repaint it. For the money the difference is worth it.
What did you do with the Trans Cooler lines? Pinch them off? Cap them? If you didn't, how much trans fluid did you lose after you removed them?
great video! Can you list all the part numbers and where did you order?
Nice detail given the instructions come with no descriptive wording, only drawings. I could not find any information about the alignment pins anywhere else. A couple notes: I was able to remove the grommets from the door frame with my fingers - no tool required. They are somewhat flexible so once you pry one side up, keep pushing until it releases. The other note is that the orientation of the slot the key goes in needs to be such that the key goes in from the bottom. If the slot is upside down, you reach a point where you can no longer insert the key to tighten or loosen the rack. I think my rack had all mounting ends fully released allowing that piece on one mounting leg to rotate.
In America most people call your French wrench a crescent wrench
I find it funny that a lot of people say be careful of using these tools and accessories because they are cheap Chinese crap but they are forgetting that the stuff they buy from Amazon, Walmart, Target and 98% of everything everything else we buy is from China.
I haven't bought from aliexpress yet bit I do have the phillips bits and bit holders from Temu and they work perfectly.
PRO TIP: they sell plastic clamps at Harbor Freight and online that are specifically for clamping down line with fluid. They are basically like vise grips, except they fully are plastic (so they are less likely to tear rubber hoses) and the jaws are flat to fully seal the hose together when you ratchet them tight. I use a couple of these when changing out cooling or fueling components and usually don't lose hardly any fluid
This is a great tutorial, i just got them wrapped with a piano black automotive film wrap and they look fantastic and it cost 25 EUR
Why won’t mine tighten,one side does but the other side wont
Great video man!
This is exactly what I was looking for! My 2018 is beginning to peel and was hoping for an easy fix like that! It's only peeling on one side buy im going to do both since it seems that the other side will eventually do the same
Will i be able to attach Yakima bike or ski racks to these bars? How does it work?
Use this to hold random drill bits by the drill press.
For $3,500, you won the damn lottery with this amazing old muscle car!
hi I have a mercedes sl 300 cab model year 1993. my question is, when the car is cold it starts, when it is warm it cannot be started until it has been sitting for a few hours, then you can start it again. can you the error would be very grateful🙏
Probably a position crank sensor. That’s the usual symptom of a broken position crank sensor.
What brand is the yellow tool organizer ?
I just learned about the existence of these toolboxes today and I found your video. My daughter thinks she needs one of these in pink for her crafting supplies. I like your handle, latch, and the wire you added to keep the lid from opening the whole way. I see I'm going to have some DIY fun as part of the setup of her toolbox.
I ended up giving this one to my mom for her sawing stuff it works great for that. The only issue with the pink one is that it’s usually always sold out at the store and you would have to buy it from a reseller at a marked up price.
@@Damiansgarage I'm in Santa Fe, NM and according to Lowe's website, pink and red are the only colors in stock near me. And there's not enough red in stock to be able to order it online and pick up in store. I'm crossing my fingers that the website is correct about the pink.
Man I wish you could add those to my toolbox. I don't have the tools and am not handy enough to add anything, including a handle. But love all your additions to the toolbox.
Question: I am looking to purchase a roof rack for my 2016 Prius. What brand is this one? I haven't finished the video, but based on different reviews on low noise, I wanted to purchase a Yakima or Thule. What brand is this one? Thank you!!! Also, How do you know how long the bars need to be when you're shopping?
OEM Roof Rack. Just got that.
Yes the OEM roof racks for the Prius are the best in my opinion because they fit perfectly and they are pretty quiet even at freeway speeds.
Do you have the website where i can buy this?
just google motodemic
❤great video and explanation
You need to change that headlight 😂
good car
I’ll use it for drag racing and drifting
I only watched, cause of the prime bottle .
Jokes on you, I only put the prime bottle in the thumbnail to make people click on the video😂
This is the realist tool cart tour I’ve seen 😂 not like everyone else “flexing” their expensive power tools and rare/handy specialty tool that we “have to buy bc it’s worth it” Just a simple, cheap tool assortment of tools that get the job done! And a few that were on sale 😂(I’m guilty of buying purely bc they’re on sale)
Great video lad
Very thorough! Thank you!!
Really beautiful bike man
just picked up an 09, always owned cruisers, wow these things are fast!😂
Those are super fun to ride in the corners too you can really have some fun with it!
Mine is incredibly slow to me. It’s still a great in town bike but once you get on the highway it’s a bit of a dog. I still love her though and won’t sell my first bike.
Do you notice any reduction in cowl shake?
I would be very cautious of using those fuses for anything - or anything cheap chinese crap related to any kind of safety. Louis Rossmann recently released a video where he tested top ranked Amazon fuses, and none of them worked properly. A 2 amp fused only blew at 10 amps. kzread.info/dash/bejne/dG1kwbWHfsXJn7g.html
Yea I don’t know how I feel about those fuses either, but then, on the other hand, all the fuses you buy at automotive stores, or the retail stores are also most likely all made in China.
@@Damiansgarage The "Made in china"- part of the "cheap chinese crap" doesnt mean it's dangerous. When a retail store imports something for selling, they are liable, if a house or a car burns down. They also have a reputation they want to hold. So they are incentivized to research and make sure what they are selling are, if not high quality, at least safe to use. But you dont have this when you go to some random ebay/amazon/aliexpress seller with no datasheets, certifications or anything to indicate if the product is safe, or are they just trying to scam you out of your money, $1,99 at a time.
Thats not a feeler guage set.. its for thread pitch
Good catch lol I didn’t even realize I was basically an auto pilot when ordering all this stuff.
Good video
Thanks
I just found your channel and subscribed. Nicely done, Brother. I hope you will do some after use videos. On well, everything works out for you. For the price you can't beat it 😅 Thank you and Merry Christmas to you and your family 😊
You think it's possible to replace the rails with like actual drawer rails? The stock ones kinda suck.
It would be a pain in the butt to do it but it isn’t possible the biggest problem I believe would be finding such a short sliders
You would need to find a slide that is about 5 inches in length (when folded) and overall thickness being less than 7mm (the gap you have on each side of the drawers) Amazon does appear to sell 5 inch slides but im not confident they will work perfectly. Perhaps you'd either have to contact a company or someone else to custom make you a set. Maybe possible to 3d print rails and get the bearing part somewhere else but im not sure the strength and durability will be any better. With that said you can try lubricating the existing slides with lithium grease. If that doesnt work you will have to remove the drawers and file down any burrs/ sharp edges present on the friction slides
@@aAbstractduck Yeah you're right, I'd probably need low profile slides. I'll look online to see if I can find some. In the meantime I'll try lubricating the slides with some grease. Thanks for the tip, friend!
@@d2cuadrados510 if you find anything let me know! Quick tip on removing the drawers without causing any damage if you need to: Take a long, thin piece of metal. Put a slight bend on one side (about an inch from the end) insert it between the drawer so that it goes around the little tab preventing the drawer from coming out and then give it a pull, preferably you have one on each side. It should pop right out. I used two 0.013" feeler gages but im sure something like a hacksaw blade would also work!
Nice
Thanks lol