Alright, after some experimentation I think I know how these work. Short press - program remote to open/close Long press - remote only turns the light on/off Really long press - clears all remotes That would have taken a fraction of a cent in ink to add to the instructions, which isn’t much considering these are $30 a pop.
@jenny1671Ай бұрын
i ripped my Kevlar belt got it caught in hood wiper and busted the belt and back window. Yes the hood was up when driving out of the garage. I can buy a new belt kit but i need a instruction video on how to measure for 7 ft door. the last belt was cut too short so i had to take few links from old belt. but now it's not feeding correctly it saggs and then tightens up.
@ACamelEmoji5 ай бұрын
If your remotes and keypad arent working with these instructions, try unpluging the lift from the ceiling and plugging it back in. We had a lightning storm and I guess a surge glitched it.
@MB-ye4el9 ай бұрын
This doesn't work, the instructions for my FCT3b keypad state to push P on the opener then press PRG button then 4 digit pin and then press ENT. The video doesn't even mention the PRG button so which is it? Why does everything have to be so difficult? The technician is also less than 3 ft from the opener while programming my instructions state to be farther away than 3 feet.
@MB-ye4el9 ай бұрын
The music is completely unnecessary.
@newmoney812810 ай бұрын
Real facts this opener trash programming is horrible I've had two and still no other and universal remote are out the window
@lucyshi388011 ай бұрын
Make sure your garage door is CLOSED before you try to program.
@elizabethbuch5006 Жыл бұрын
Thank you for publishing this video. It was easy to follow and helped me feel safer in my home.
@elizabethbuch5006 Жыл бұрын
I found this very helpful and easy to follow. Thank you for taking the time to publish.
@frkafkaz Жыл бұрын
😂
@timelessr94072 жыл бұрын
Guys, you must also be holding the program button on the remote simultaneously when pressing P. Otherwise it will not set
@blitz3643 Жыл бұрын
This was the trick. Thank you!
@shinerburke2 жыл бұрын
I am having a maddening issue. Since everything was installed our keypad has periodically lost the ability to open the door, but could be reprogrammed. Now, in the last month it has lost the code 3 times. It, and the opener, are barely a year old. I have replaced the battery, same issue. I have reprogrammed the keypad, it works for a while, then loses the code. Somehow now it will open the door with the press of any button, but to close the door the code is required. Makes zero sense. Frankly I think this product is garbage. If I had been given a choice of product by our builder I certainly would not have picked this equipment.
@larrytate1657 Жыл бұрын
Hormanns doors are great but when it comes to motors lift master.
@spikewiebe2 жыл бұрын
Turn off the awfull music and verbally explain the instructions.
@MarshallCouch2 жыл бұрын
why would pressing a single digit from my pin open the garage door? Seems like only the enter button should send a radio signal.
@fictionalhead7 ай бұрын
Probably won't help you a year later, but for future people who have this issue -- The code seems to store in the device for like 30s-1m after you enter it. So when you initially program it, and then attempt to test it, any button triggers the door to go. Any number, enter, doesn't matter -- anything will make it operate when the code is 'active'. After programming, if you wait like 1min or so, then try it, only your programmed code will make it go. I have to assume it stores the code as 'accepted' for a tiny period of time for ease of use once you enter the right code, but it ends up just being super confusing.
@MarshallCouch2 жыл бұрын
I accidentally reset my garage door opener, tried to reconnect the keypad. and now any button on the keypad opens the garage door. very secure.
@shinerburke2 жыл бұрын
I am having a similar issue. Since everything was installed our keypad has periodically lost the ability to open the door, but could be reprogrammed. Now, in the last month it has lost the code 3 times. It, and the opener, are barely a year old. I have replaced the battery, same issue. Keeps losing the code. Somehow now it will open with the press of any button, but to close it the code is required. Frankly I think this product is garbage.
@randallfraley28102 жыл бұрын
I have a question I have a Hormann silent drive 5500 series garage door opener. I ordered this Hormann key pad that goes to it. I programmed it just like the instructions said to but it will only turn the light on and off when I put my code in . What would cause this to happen? The garage door will not go up or down only turn the lights on and off. Thanks Randall
@timelessr94072 жыл бұрын
Also you have to be holding the Program button on the remote at the same time you press p on the opener
@jerryray2043 жыл бұрын
Can you have more than one working PIN number at a time?
@AllSpeed5413 жыл бұрын
Garbage keypad works like a remote. Any damn button I press opens the door.
@jeremyhooke61603 жыл бұрын
Glad to see someone else is having the same problem I am….Junk!!!!!
@fictionalhead7 ай бұрын
Probably won't help you years later, but for future people who have this issue -- The code seems to store in the device for like 30s-1m after you enter it. So when you initially program it, and then attempt to test it, any button triggers the door to go. Any number, enter, doesn't matter -- anything will make it operate when the code is 'active'. After programming, if you wait like 1min or so, then try it, only your programmed code will make it go. I have to assume it stores the code as 'accepted' for a tiny period of time for ease of use once you enter the right code, but it ends up just being super confusing.
@mantalsing3 ай бұрын
@@fictionalheadHey do you maybe know why doors open when i press doorbell/light button? It should open only when I type in the selected code. Thanks in advance for answer
@nomehdrider3 жыл бұрын
Well, I couldn't get it to take a PIN, on mine: Press the "P" Key, then (the step I needed) press the program key. Now put in the PIN and hit enter and now it works, again for me. I called the number supplied, they forwarded me to another person, they said it sounded to technical for them, so they gave a garage door company in the area, I didn't call them...
@matteog.33184 жыл бұрын
Hi! How i can reset the transmitter?
@tcalado3 жыл бұрын
Trying to know this too
@nlmaster98113 күн бұрын
Holding down the program button until it flashes will clear all of the remotes.
@TechMorePayLess4 жыл бұрын
The drive belt overshot and no way to reverse the belt
@pendejodelllano27943 жыл бұрын
Tengo el mismo problema alguien me puede ayudar
@billhansen82164 жыл бұрын
My reprogramming worked exactly as your video said it should work Thanks
@gradyguin72162 жыл бұрын
What was it doing before ??? Mine was working fine when I went to bed and in the morning it would act like it was obstructed on the way down,,senor on 1 side was green but other was red,,I moved sensors to match as I had to do that before,,after I reset it never tried to retrain
@chevelleman884 жыл бұрын
This babe is where it’s at. I hope she bears many children.
@kaymarfrancis1644 жыл бұрын
hello how can i program a second remote?
@OtterMotterPia5 жыл бұрын
If you forgot the original pin needed to make the change. How can this be fixed?
@HormannGroupNorthAmerica5 жыл бұрын
You can try the procedure to "Factory Reset" the keypad and follow the programming procedure. Click kzread.info/dash/bejne/ZaZ_mpN-qcS9YMo.html for Factory Reset instruction.
@mrmike12966 жыл бұрын
Love being part of the family, Lord Bless
@alexfregosi933212 жыл бұрын
Oh and by the way, galvanized springs also rust. They develop a white-rust appearance on the coils with time. But when they break, it's because of steel fatigue, not rust. And all springs, whether oil-tempered, galvanized, or powder-coated, should be lubed at least once a year (preferably every 3-4 months) to keep the door operating properly.
@alexfregosi933212 жыл бұрын
Rust IS NOT the primary cause of spring failure; metal fatigue is. Every time a garage door goes up and down, the spring steel wire flexes and with time the steel wire flexes beyond its intended point and breaks. Galvanized springs are a nice marketing gimmick but they are terrible. They tend to lose tension after installation, requiring several service calls to rewind them. I've been in the garage door industry for 32 yrs and oil tempered springs are truly the best springs out there.
Пікірлер
Alright, after some experimentation I think I know how these work. Short press - program remote to open/close Long press - remote only turns the light on/off Really long press - clears all remotes That would have taken a fraction of a cent in ink to add to the instructions, which isn’t much considering these are $30 a pop.
i ripped my Kevlar belt got it caught in hood wiper and busted the belt and back window. Yes the hood was up when driving out of the garage. I can buy a new belt kit but i need a instruction video on how to measure for 7 ft door. the last belt was cut too short so i had to take few links from old belt. but now it's not feeding correctly it saggs and then tightens up.
If your remotes and keypad arent working with these instructions, try unpluging the lift from the ceiling and plugging it back in. We had a lightning storm and I guess a surge glitched it.
This doesn't work, the instructions for my FCT3b keypad state to push P on the opener then press PRG button then 4 digit pin and then press ENT. The video doesn't even mention the PRG button so which is it? Why does everything have to be so difficult? The technician is also less than 3 ft from the opener while programming my instructions state to be farther away than 3 feet.
The music is completely unnecessary.
Real facts this opener trash programming is horrible I've had two and still no other and universal remote are out the window
Make sure your garage door is CLOSED before you try to program.
Thank you for publishing this video. It was easy to follow and helped me feel safer in my home.
I found this very helpful and easy to follow. Thank you for taking the time to publish.
😂
Guys, you must also be holding the program button on the remote simultaneously when pressing P. Otherwise it will not set
This was the trick. Thank you!
I am having a maddening issue. Since everything was installed our keypad has periodically lost the ability to open the door, but could be reprogrammed. Now, in the last month it has lost the code 3 times. It, and the opener, are barely a year old. I have replaced the battery, same issue. I have reprogrammed the keypad, it works for a while, then loses the code. Somehow now it will open the door with the press of any button, but to close the door the code is required. Makes zero sense. Frankly I think this product is garbage. If I had been given a choice of product by our builder I certainly would not have picked this equipment.
Hormanns doors are great but when it comes to motors lift master.
Turn off the awfull music and verbally explain the instructions.
why would pressing a single digit from my pin open the garage door? Seems like only the enter button should send a radio signal.
Probably won't help you a year later, but for future people who have this issue -- The code seems to store in the device for like 30s-1m after you enter it. So when you initially program it, and then attempt to test it, any button triggers the door to go. Any number, enter, doesn't matter -- anything will make it operate when the code is 'active'. After programming, if you wait like 1min or so, then try it, only your programmed code will make it go. I have to assume it stores the code as 'accepted' for a tiny period of time for ease of use once you enter the right code, but it ends up just being super confusing.
I accidentally reset my garage door opener, tried to reconnect the keypad. and now any button on the keypad opens the garage door. very secure.
I am having a similar issue. Since everything was installed our keypad has periodically lost the ability to open the door, but could be reprogrammed. Now, in the last month it has lost the code 3 times. It, and the opener, are barely a year old. I have replaced the battery, same issue. Keeps losing the code. Somehow now it will open with the press of any button, but to close it the code is required. Frankly I think this product is garbage.
I have a question I have a Hormann silent drive 5500 series garage door opener. I ordered this Hormann key pad that goes to it. I programmed it just like the instructions said to but it will only turn the light on and off when I put my code in . What would cause this to happen? The garage door will not go up or down only turn the lights on and off. Thanks Randall
Also you have to be holding the Program button on the remote at the same time you press p on the opener
Can you have more than one working PIN number at a time?
Garbage keypad works like a remote. Any damn button I press opens the door.
Glad to see someone else is having the same problem I am….Junk!!!!!
Probably won't help you years later, but for future people who have this issue -- The code seems to store in the device for like 30s-1m after you enter it. So when you initially program it, and then attempt to test it, any button triggers the door to go. Any number, enter, doesn't matter -- anything will make it operate when the code is 'active'. After programming, if you wait like 1min or so, then try it, only your programmed code will make it go. I have to assume it stores the code as 'accepted' for a tiny period of time for ease of use once you enter the right code, but it ends up just being super confusing.
@@fictionalheadHey do you maybe know why doors open when i press doorbell/light button? It should open only when I type in the selected code. Thanks in advance for answer
Well, I couldn't get it to take a PIN, on mine: Press the "P" Key, then (the step I needed) press the program key. Now put in the PIN and hit enter and now it works, again for me. I called the number supplied, they forwarded me to another person, they said it sounded to technical for them, so they gave a garage door company in the area, I didn't call them...
Hi! How i can reset the transmitter?
Trying to know this too
Holding down the program button until it flashes will clear all of the remotes.
The drive belt overshot and no way to reverse the belt
Tengo el mismo problema alguien me puede ayudar
My reprogramming worked exactly as your video said it should work Thanks
What was it doing before ??? Mine was working fine when I went to bed and in the morning it would act like it was obstructed on the way down,,senor on 1 side was green but other was red,,I moved sensors to match as I had to do that before,,after I reset it never tried to retrain
This babe is where it’s at. I hope she bears many children.
hello how can i program a second remote?
If you forgot the original pin needed to make the change. How can this be fixed?
You can try the procedure to "Factory Reset" the keypad and follow the programming procedure. Click kzread.info/dash/bejne/ZaZ_mpN-qcS9YMo.html for Factory Reset instruction.
Love being part of the family, Lord Bless
Oh and by the way, galvanized springs also rust. They develop a white-rust appearance on the coils with time. But when they break, it's because of steel fatigue, not rust. And all springs, whether oil-tempered, galvanized, or powder-coated, should be lubed at least once a year (preferably every 3-4 months) to keep the door operating properly.
Rust IS NOT the primary cause of spring failure; metal fatigue is. Every time a garage door goes up and down, the spring steel wire flexes and with time the steel wire flexes beyond its intended point and breaks. Galvanized springs are a nice marketing gimmick but they are terrible. They tend to lose tension after installation, requiring several service calls to rewind them. I've been in the garage door industry for 32 yrs and oil tempered springs are truly the best springs out there.