Just did the same thing to my boat, hopefully it works out as well.
@lurifax7382 Жыл бұрын
Great mods! i have the same boat, but havent tried it yet.I will suggest all that get this boat to check all the screws before you use it.Mine came with alot of lose screws.Many of the screws on my boat wasnt fastened to the inside plate that holds the steering rod etc.(the screws wasnt fastened to the screw holes in the plate) Think i will zip tie and move that water nipple to the left side of the boat as you have done :)
@DarkKent2 жыл бұрын
Great vid as always. Can you reccomend a good servo update. Mine went.
@jakeaird82202 жыл бұрын
I’d go a cheaper Savox servo that’s what I have in it now it is a lot more responsive
@DarkKent2 жыл бұрын
@@jakeaird8220 thanks for the reply. How many g. Noob of course lol
@danilomontagnini54832 жыл бұрын
If you do not put the scoch water enters? thank you
@jakeaird82202 жыл бұрын
Only a little when you tip it over but it’s really not too much
@Nanoscape302 жыл бұрын
How did you take take the original exit port out of the back top left of the boat?
@jakeaird82202 жыл бұрын
Just put a sticker over the back hole and drilled a 4.5mm hole if I remember correctly and pushed the same water grommet from the back into the side with a tad bit of super glue and zip tied it on
@MaxPower-zp7wy5 ай бұрын
Did you fill in the original exit port with anything else other than the sticker ? I hope it's water proof water tight ;/
@AlexAlex-pf2yf2 жыл бұрын
Hello. I would be very grateful if it is possible to say the marking of electronic elements of the charging board under the translucent glass. Some elements elements burned out in my lantern and their marking are not visible. I want to fix it myself. Thanks!
@jakeaird82202 жыл бұрын
Add me on insta jakeaird
@terachartthayakorn51752 жыл бұрын
How did you move the water cooling on the motor heat sink from the top to side? Thanks
@jakeaird82202 жыл бұрын
That model came with it
@forumanomaly2 жыл бұрын
Very useful video, thanks. Been looking for a video of the Pro that shows something other than turbo, and finally found yours, exactly what I had been looking for 😊
@michaeledmonds30273 жыл бұрын
Thanks for the clean out and tie down tips. I'm sure your propshaft is well lubed. Nice video... Banggood is kind of a crap shoot. When you receive busted stuff, be sure to send them closeup photos of damage right away. Then look for near hidden info requests in response so that they process your "ticket". Will take weeks for refund if you do everything right. Amazon is more money for sure, but WAY more professional. Enjoy your boat!
@rccrawlerextreme3 жыл бұрын
Nice review
@JuanGarcia-oz6sg3 жыл бұрын
Do the plugs come in xt90 or xt60 plz answer
@dmitriybeyu48073 жыл бұрын
xt60
@mahesapemuda67503 жыл бұрын
That's good!
@joeframo33473 жыл бұрын
The one I ordered is the GT pro the newer model and it throws out 3500 Lumens it sells for close to $50 but it's well worth the money I like the ramp part of it I think that's one of my favorite features instead of clicking buttons which is a pain in the ass sometimes especially if you're in a hurry every damn thrower light should have that ramping system Lumentop is one of the best flashlights out on the market and I've been studying a lot of them they're all good but this company has a ramping system which I really like I wish they all had that system thank you for sharing your video young man 💲🥰❤️😎🤠🖐️💰
@joeframo33473 жыл бұрын
This one's a lot better than the first version of just the GT mini the GT mini pro is so much better it's got more throwing power
@joeframo33473 жыл бұрын
Your video is also poor I have to scout around and find somebody that has correct measurements on how this light throws y'all want to be superstars on KZread 😜😭😭😭😭😭
@joeframo33473 жыл бұрын
Let me see how your video is cuz everybody else is screwed up they have not taken measurements they're just guessing and therefore we're not subscribing to their channel let's see what you have to offer on this flashlight 😎🖐️
@185ez33 жыл бұрын
Beware of Banggood. Terrible customer service. I may have had debris in my water lines like yours and the esc over heated. Boat would stop and start randomly and crashed. They say it's all my fault even with video and picture evidence
@jakeaird82203 жыл бұрын
Yep high chance of that happening as they are cheap so quality control is like zero so I went over everything and tightened and greased before I ran it and mine has been fine since
@185ez33 жыл бұрын
@@jakeaird8220 Yes, good deal for what it is but they should still own up to a defective product. Banggood doesn't even have most spare parts so I ordered everything from Monkey Hobby
@jakeaird82203 жыл бұрын
@@185ez3 I ended up getting a full refund after sending this video to them as they want me to delete it but I want to show everyone how to fix it and make it better
@185ez33 жыл бұрын
Why did you think the cooling system wasn't right? I do like the idea of the fitting off to the side. Banggood isn't helping me with a defective boat. I have both the sr80 and pro.
@jakeaird82203 жыл бұрын
There was metal filing left in the motors heat sink and to shoot water up takes for effort that shooting it side wards
@185ez33 жыл бұрын
@@jakeaird8220 I did the side cooling outlet on the side. Makes sense, thanks
@tex99603 жыл бұрын
Hey dude do you know of the sr80 and sr80 pro use the same prop shaft and prop? Thankyou
@185ez33 жыл бұрын
No, they are different length shafts and thickness. Props are not interchangeable
@tex99603 жыл бұрын
@@185ez3 perfect thankyou man 💯💯
@luckeyee51393 жыл бұрын
What that guy said. I have the sr80, broke the prop and shaft so ordered the pro version by mistake and didn't fit. I did find a bigger prop for my boat and itis a lot faster
@arauxo3 жыл бұрын
Does not appear to have a waterproof cover.
@jakeaird82203 жыл бұрын
Black black top cover is the “waterproof cover “ it’s not great but put tape around it and it’s all sweet
@zeeek13 жыл бұрын
Sharpen and balance your props and you will gain more speed.
@nicholasadams99543 жыл бұрын
Nice bro! Just got mine 2 days ago 🤙🏽can’t wait to start modding it 😎
@miguelsalami3 жыл бұрын
THE SR80 MOD SQUAD ARE ON THEIR WAY➡PAUL & CASEY😎
@jakeaird82203 жыл бұрын
Just wait to you see what I am doing to it this weekend 😉
@jakeaird82203 жыл бұрын
I just need your opinion a 120 amp 6s or 90 amp 6s esc
@miguelsalami3 жыл бұрын
@@jakeaird8220 Jake I have help on the way for you man just messaged Paul & Casey They are the HotRod Kings of RC.
@jakeaird82203 жыл бұрын
@@paulcooper7162 ok thank you I will be looking at the esc an I’ll choose some flotation
@miguelsalami3 жыл бұрын
If you turn your comments on in your Vector SR80 Vid the guys will chime in & chat with you. My SR80 just arrived took 2 months to get here & still need a 4S battery.
@jakeaird82203 жыл бұрын
Turned the comments on on the sr 80 video
@miguelsalami3 жыл бұрын
@@jakeaird8220 EXCELLENT❗
@majoroverkill13763 жыл бұрын
Actually from watching your video you only reached the high ramp mode, you need to double click in high ramp for turbo mode then the flashlight will put out its full 3500lms. It should easily light up those trees at 100 yards and beyond. I own many of the GT flashlights and that is how they all work or should i say the Anduril UI works. Great video, thank you.
@jakeaird82203 жыл бұрын
Sorry I I didn't double click from what I have seen with this torch between hight ramp and turbo is no difference to my eyes
Пікірлер
Nice video Jake. Thanks for sharing
Just did the same thing to my boat, hopefully it works out as well.
Great mods! i have the same boat, but havent tried it yet.I will suggest all that get this boat to check all the screws before you use it.Mine came with alot of lose screws.Many of the screws on my boat wasnt fastened to the inside plate that holds the steering rod etc.(the screws wasnt fastened to the screw holes in the plate) Think i will zip tie and move that water nipple to the left side of the boat as you have done :)
Great vid as always. Can you reccomend a good servo update. Mine went.
I’d go a cheaper Savox servo that’s what I have in it now it is a lot more responsive
@@jakeaird8220 thanks for the reply. How many g. Noob of course lol
If you do not put the scoch water enters? thank you
Only a little when you tip it over but it’s really not too much
How did you take take the original exit port out of the back top left of the boat?
Just put a sticker over the back hole and drilled a 4.5mm hole if I remember correctly and pushed the same water grommet from the back into the side with a tad bit of super glue and zip tied it on
Did you fill in the original exit port with anything else other than the sticker ? I hope it's water proof water tight ;/
Hello. I would be very grateful if it is possible to say the marking of electronic elements of the charging board under the translucent glass. Some elements elements burned out in my lantern and their marking are not visible. I want to fix it myself. Thanks!
Add me on insta jakeaird
How did you move the water cooling on the motor heat sink from the top to side? Thanks
That model came with it
Very useful video, thanks. Been looking for a video of the Pro that shows something other than turbo, and finally found yours, exactly what I had been looking for 😊
Thanks for the clean out and tie down tips. I'm sure your propshaft is well lubed. Nice video... Banggood is kind of a crap shoot. When you receive busted stuff, be sure to send them closeup photos of damage right away. Then look for near hidden info requests in response so that they process your "ticket". Will take weeks for refund if you do everything right. Amazon is more money for sure, but WAY more professional. Enjoy your boat!
Nice review
Do the plugs come in xt90 or xt60 plz answer
xt60
That's good!
The one I ordered is the GT pro the newer model and it throws out 3500 Lumens it sells for close to $50 but it's well worth the money I like the ramp part of it I think that's one of my favorite features instead of clicking buttons which is a pain in the ass sometimes especially if you're in a hurry every damn thrower light should have that ramping system Lumentop is one of the best flashlights out on the market and I've been studying a lot of them they're all good but this company has a ramping system which I really like I wish they all had that system thank you for sharing your video young man 💲🥰❤️😎🤠🖐️💰
This one's a lot better than the first version of just the GT mini the GT mini pro is so much better it's got more throwing power
Your video is also poor I have to scout around and find somebody that has correct measurements on how this light throws y'all want to be superstars on KZread 😜😭😭😭😭😭
Let me see how your video is cuz everybody else is screwed up they have not taken measurements they're just guessing and therefore we're not subscribing to their channel let's see what you have to offer on this flashlight 😎🖐️
Beware of Banggood. Terrible customer service. I may have had debris in my water lines like yours and the esc over heated. Boat would stop and start randomly and crashed. They say it's all my fault even with video and picture evidence
Yep high chance of that happening as they are cheap so quality control is like zero so I went over everything and tightened and greased before I ran it and mine has been fine since
@@jakeaird8220 Yes, good deal for what it is but they should still own up to a defective product. Banggood doesn't even have most spare parts so I ordered everything from Monkey Hobby
@@185ez3 I ended up getting a full refund after sending this video to them as they want me to delete it but I want to show everyone how to fix it and make it better
Why did you think the cooling system wasn't right? I do like the idea of the fitting off to the side. Banggood isn't helping me with a defective boat. I have both the sr80 and pro.
There was metal filing left in the motors heat sink and to shoot water up takes for effort that shooting it side wards
@@jakeaird8220 I did the side cooling outlet on the side. Makes sense, thanks
Hey dude do you know of the sr80 and sr80 pro use the same prop shaft and prop? Thankyou
No, they are different length shafts and thickness. Props are not interchangeable
@@185ez3 perfect thankyou man 💯💯
What that guy said. I have the sr80, broke the prop and shaft so ordered the pro version by mistake and didn't fit. I did find a bigger prop for my boat and itis a lot faster
Does not appear to have a waterproof cover.
Black black top cover is the “waterproof cover “ it’s not great but put tape around it and it’s all sweet
Sharpen and balance your props and you will gain more speed.
Nice bro! Just got mine 2 days ago 🤙🏽can’t wait to start modding it 😎
THE SR80 MOD SQUAD ARE ON THEIR WAY➡PAUL & CASEY😎
Just wait to you see what I am doing to it this weekend 😉
I just need your opinion a 120 amp 6s or 90 amp 6s esc
@@jakeaird8220 Jake I have help on the way for you man just messaged Paul & Casey They are the HotRod Kings of RC.
@@paulcooper7162 ok thank you I will be looking at the esc an I’ll choose some flotation
If you turn your comments on in your Vector SR80 Vid the guys will chime in & chat with you. My SR80 just arrived took 2 months to get here & still need a 4S battery.
Turned the comments on on the sr 80 video
@@jakeaird8220 EXCELLENT❗
Actually from watching your video you only reached the high ramp mode, you need to double click in high ramp for turbo mode then the flashlight will put out its full 3500lms. It should easily light up those trees at 100 yards and beyond. I own many of the GT flashlights and that is how they all work or should i say the Anduril UI works. Great video, thank you.
Sorry I I didn't double click from what I have seen with this torch between hight ramp and turbo is no difference to my eyes
Comment what light you want me to review next