Hi Sir!!! thank you so much!!!!! sorry for bother you, but do you know how can i change the oil transmission? thanks in advance.
@cole15millerАй бұрын
My steering locked up and had no signs till it just happened one day after a rainy day. It’s super hard to turn steering wheel in any direction so you Think it’s the same problem ?.
@jerimiahmetcalf42772 ай бұрын
Should remove music so we can hear what you are saying. Thank you for the video
@djsthemetereman3 ай бұрын
Drone mobile is an excellent Alarm
@wendell54543 ай бұрын
✔️ Promo*SM
@techguy09274 ай бұрын
Ilan ft lb filter and drain plug?
@ShionWinkler4 ай бұрын
Today's video: How to cause permanent back damage in one easy step. 🤣No really, don't do this, it will mess your back up.
@liamhawkins40624 ай бұрын
Wouldn’t it make obvious sense to lower the car first…..
@cornyeah88004 ай бұрын
no he is doing it right
@nicolasbailon25114 ай бұрын
Will this process work on a manual-transmission subaru?
@mangerningmechanic79314 ай бұрын
Yes sir
@user-cg2ru7oz1m4 ай бұрын
And that would be $200 😂 awesome vid 👏
@2jzgenat4 ай бұрын
Should be more
@KingDrew114 ай бұрын
It's your background music that's keeping your views low. Pivot to tutorial or atleast voice over explanations on the video...good luck
@mangerningmechanic79314 ай бұрын
Okay thanks for your advise , Just a biggener KZreadr 🤗
@naiicks50345 ай бұрын
Hello sir, thank you for the video. Where do you see the torque value ?
@techguy09275 ай бұрын
Finally 🙌🙌🙌
@basedSTi5 ай бұрын
i have this on my 21 sti and suspect its draining the battery... how do i disconnect it being that i didnt install it myself?
@trappedbanana72405 ай бұрын
Used to work there😢 miss it
@everves5 ай бұрын
He's talking like -6 is cold 🤣
@thatdudeoverthere-xh8pu5 ай бұрын
I mean, it's not warm is it?
@Willbertoslackbold5 ай бұрын
Wtf do u mean 😂 yes -6 is cold even in metic. If you can die from being outside too long without proper clothing then it’s cold. Just because you might experience colder temperatures it doesn’t mean that literal freezing temperatures arnt cold!! 😂
@Nku2225 ай бұрын
If you think -6 is cold u need to grow a pair
@mangerningmechanic79315 ай бұрын
Yes sir winter season And it’s -6*c with wind chill
@ericklomas73365 ай бұрын
Push rods are different size?
@stevensapyak7971Ай бұрын
6.5.24. ☝🏼Exhaust push rods are longer than the intake pushrods🎯
@user-wz3ct3xb5g5 ай бұрын
Where are you based?
@ayden75596 ай бұрын
Promo>SM 😩
@Phuong.Nguyen-7 ай бұрын
Awesome ❤😊
@haiselcastillogarcia7527 ай бұрын
Funciona en cual quier auto
@Snowgang687 ай бұрын
I want to do this install myself, any tips? Unfortunately I can’t see what you plug in and take out etc. got the same car 2018 manual wrx but turn key. How can I get in touch with you?
@chimitoc56607 ай бұрын
Doy you have to carry the original key fob with you always.?
@DesertEagle907 ай бұрын
That dont look too bad! But then again I only got the compustar cs4900-s itself... Think I would need anything else??? I was gonna use the t taps instead of sodering. I'm using the 17 Subaru WRX
@Dwigt_Rortugal8 ай бұрын
Me: "There's no way this is a full installation video at 7 minutes!" And yet there it is. This looks surprisingly doable. Not too much splicing.
@marianajaldin27578 ай бұрын
What went wrong with that valve? Too tight???
@erwincinco523810 ай бұрын
how much the cost pra sa rebuild ng transmission.
@nelver111 ай бұрын
how do you take the frozen bolts from loose nuts off the timing belt cover from a 1999 subaru forester gt
@mangerningmechanic793111 ай бұрын
hi thank you for commenting. usually I'm using vise grip to hold it or snap it
@Nick-sj5nx11 ай бұрын
What gauge wire works best for this method?
@user-dd5kd1zi8f Жыл бұрын
like watch your show, great information i can use on some of the cars that i work on. I worked as a Mechanic ( now retired) for a well known beer company and i Hated having to work on the diesel truck coming from back east because of the rust and rotted metal i'll keep suffering in calif with the fruits and nut and no rust Thanks for time you put into your channel
@mangerningmechanic793111 ай бұрын
thank you for watching
@mariomellarpes-yl8dk Жыл бұрын
HI Tta @Caroline iDrone installation muna si Rudolph sa Pinas at si Mang Erningsss tlaga ang SAKALAM...haha😅😂😅
@duchberryswagg Жыл бұрын
How do you reset the system after the car battery dies
@studioxps7210 ай бұрын
Just relearn the system.
@-U-m-a-r- Жыл бұрын
✨Natural air conditioners✨
@venurafernando Жыл бұрын
WOW this is great. I have the same problem. Where are do based in Canada ? and what will be the total cost to repair this ?
@ibechuu9695 Жыл бұрын
Wish you did a before and after with the noises
@DKSE123 Жыл бұрын
I had a 2001 fozzy years back. I bought it with a semi blown timing kit at 168,000 for $1100.00 . After replacing the timing kit , it ran perfect . I sold it at 223,000 , still ran perfect . By far , one of the best cars I ever owned .
@josephpalacios1159 Жыл бұрын
Good job 👏
@skuitaress Жыл бұрын
My push button start is starting to fail. 2015 VWConvertible Beetle. Any intel on DIY repair?
@mangerningmechanic7931 Жыл бұрын
Wont start but still cranking, Or no cranking at all? If no cranking at check your battery first If Wont start but still cranking check ignition system, fuel system and engine timing
@luwiekleyn4594 Жыл бұрын
how did you get the ac pipe that goes on the top drivers side of the engine off?
@mortal3nginegaming918 Жыл бұрын
San ka dto sa canada boss?
@eddieex4666 Жыл бұрын
Better camera man
@alexanderstefanxandraswedi5835 Жыл бұрын
❤😂
@troybarker682 Жыл бұрын
Watching him install the front sub frame and rack itself with an impact wrench is why I work on my cars myself....lol
@cubicattache Жыл бұрын
Do you try to buy t-harness?
@mangerningmechanic7931 Жыл бұрын
I always do hardwiring
@melissamcallister2867 Жыл бұрын
Rocker arms go first then push rod not using the removal tool increases your chances of pulling the threads out of the heads when tighting the rockers
@stevensapyak7971Ай бұрын
6.5.24. You are Absolutely Correct🙍🏻♀️ … Use the Lisle™️ 48300 rocker arm lifting tool, so you can remove the push rods without loosening the rocker arm bolts. If you do not purchase and utilize the tool, then you need to make sure that each cylinder is at top dead center on its compression stroke, for each cylinder you’re working on! That way the valves are on their seats, not being actuated by the cam. If you don’t do that, then you risk stripping out the aluminum threads in the head for the rocker arm bolts⚠️You also have to do it for reinstallation if you don’t have the tool☝🏼 KZread is replete with videos of engines, knocking after the threads are stripped out of the rocker arm, bolt holes in the head😲
@Eben18 Жыл бұрын
which subscription did you get?
@whowho7969 Жыл бұрын
What’s the torque for the rockers ?
@mangerningmechanic7931 Жыл бұрын
Install the valve arm bolts and tighten to 32N.m (24lb ft)
@whowho7969 Жыл бұрын
Thanks
@dsam0194 Жыл бұрын
Sir san kayo located?
@mangerningmechanic7931 Жыл бұрын
Sir located Po Kami sa Regina Saskatchewan Canada
@treijunta1467 Жыл бұрын
friend, is it normal for this to discharge my car battery in one day? I think it was a bad installation or faulty equipment
@mangerningmechanic7931 Жыл бұрын
Hello might something high current ampere draw discharging your battery, check for parasitic or ampere draw , with remote starter module connected and disconnected. If there’s a high current ampere draw when remote starter connected might be bad remote starter module.
Пікірлер
Hi Sir!!! thank you so much!!!!! sorry for bother you, but do you know how can i change the oil transmission? thanks in advance.
My steering locked up and had no signs till it just happened one day after a rainy day. It’s super hard to turn steering wheel in any direction so you Think it’s the same problem ?.
Should remove music so we can hear what you are saying. Thank you for the video
Drone mobile is an excellent Alarm
✔️ Promo*SM
Ilan ft lb filter and drain plug?
Today's video: How to cause permanent back damage in one easy step. 🤣No really, don't do this, it will mess your back up.
Wouldn’t it make obvious sense to lower the car first…..
no he is doing it right
Will this process work on a manual-transmission subaru?
Yes sir
And that would be $200 😂 awesome vid 👏
Should be more
It's your background music that's keeping your views low. Pivot to tutorial or atleast voice over explanations on the video...good luck
Okay thanks for your advise , Just a biggener KZreadr 🤗
Hello sir, thank you for the video. Where do you see the torque value ?
Finally 🙌🙌🙌
i have this on my 21 sti and suspect its draining the battery... how do i disconnect it being that i didnt install it myself?
Used to work there😢 miss it
He's talking like -6 is cold 🤣
I mean, it's not warm is it?
Wtf do u mean 😂 yes -6 is cold even in metic. If you can die from being outside too long without proper clothing then it’s cold. Just because you might experience colder temperatures it doesn’t mean that literal freezing temperatures arnt cold!! 😂
If you think -6 is cold u need to grow a pair
Yes sir winter season And it’s -6*c with wind chill
Push rods are different size?
6.5.24. ☝🏼Exhaust push rods are longer than the intake pushrods🎯
Where are you based?
Promo>SM 😩
Awesome ❤😊
Funciona en cual quier auto
I want to do this install myself, any tips? Unfortunately I can’t see what you plug in and take out etc. got the same car 2018 manual wrx but turn key. How can I get in touch with you?
Doy you have to carry the original key fob with you always.?
That dont look too bad! But then again I only got the compustar cs4900-s itself... Think I would need anything else??? I was gonna use the t taps instead of sodering. I'm using the 17 Subaru WRX
Me: "There's no way this is a full installation video at 7 minutes!" And yet there it is. This looks surprisingly doable. Not too much splicing.
What went wrong with that valve? Too tight???
how much the cost pra sa rebuild ng transmission.
how do you take the frozen bolts from loose nuts off the timing belt cover from a 1999 subaru forester gt
hi thank you for commenting. usually I'm using vise grip to hold it or snap it
What gauge wire works best for this method?
like watch your show, great information i can use on some of the cars that i work on. I worked as a Mechanic ( now retired) for a well known beer company and i Hated having to work on the diesel truck coming from back east because of the rust and rotted metal i'll keep suffering in calif with the fruits and nut and no rust Thanks for time you put into your channel
thank you for watching
HI Tta @Caroline iDrone installation muna si Rudolph sa Pinas at si Mang Erningsss tlaga ang SAKALAM...haha😅😂😅
How do you reset the system after the car battery dies
Just relearn the system.
✨Natural air conditioners✨
WOW this is great. I have the same problem. Where are do based in Canada ? and what will be the total cost to repair this ?
Wish you did a before and after with the noises
I had a 2001 fozzy years back. I bought it with a semi blown timing kit at 168,000 for $1100.00 . After replacing the timing kit , it ran perfect . I sold it at 223,000 , still ran perfect . By far , one of the best cars I ever owned .
Good job 👏
My push button start is starting to fail. 2015 VWConvertible Beetle. Any intel on DIY repair?
Wont start but still cranking, Or no cranking at all? If no cranking at check your battery first If Wont start but still cranking check ignition system, fuel system and engine timing
how did you get the ac pipe that goes on the top drivers side of the engine off?
San ka dto sa canada boss?
Better camera man
❤😂
Watching him install the front sub frame and rack itself with an impact wrench is why I work on my cars myself....lol
Do you try to buy t-harness?
I always do hardwiring
Rocker arms go first then push rod not using the removal tool increases your chances of pulling the threads out of the heads when tighting the rockers
6.5.24. You are Absolutely Correct🙍🏻♀️ … Use the Lisle™️ 48300 rocker arm lifting tool, so you can remove the push rods without loosening the rocker arm bolts. If you do not purchase and utilize the tool, then you need to make sure that each cylinder is at top dead center on its compression stroke, for each cylinder you’re working on! That way the valves are on their seats, not being actuated by the cam. If you don’t do that, then you risk stripping out the aluminum threads in the head for the rocker arm bolts⚠️You also have to do it for reinstallation if you don’t have the tool☝🏼 KZread is replete with videos of engines, knocking after the threads are stripped out of the rocker arm, bolt holes in the head😲
which subscription did you get?
What’s the torque for the rockers ?
Install the valve arm bolts and tighten to 32N.m (24lb ft)
Thanks
Sir san kayo located?
Sir located Po Kami sa Regina Saskatchewan Canada
friend, is it normal for this to discharge my car battery in one day? I think it was a bad installation or faulty equipment
Hello might something high current ampere draw discharging your battery, check for parasitic or ampere draw , with remote starter module connected and disconnected. If there’s a high current ampere draw when remote starter connected might be bad remote starter module.
Gracias de Guatemala