Пікірлер

• 
  @mavic615510 күн бұрын

  Wouldn’t it be nice if everyone could ask you their technical questions on one of the HF bands, instead of using the Internet for that? Hmm.

• 
  @CaciqueGuerrero28 күн бұрын

  Hello sir I have a question can you connect it toma cobra 29 Ltd classic

• 
  @frankenscience3553Ай бұрын

  thanks. can you show/ explain your dipole please?

• 
  @Gw0wvlАй бұрын

  Please look at my video on the short 40 dipole 👍

• 
  @frankenscience3553Ай бұрын

  @@Gw0wvl thankyou sir, appreciate your time. have a good day.

• 
  @davidberry7985Ай бұрын

  Nice video my Encoder has jumped the odd frequency for years now but only does it when I change frequency fast. Might just change mine as I really like the push to do the span seems like a pretty good mod. I've done a few mods to mine over the years always loved this little radio it's got me all over the world. Cheers for the info really appreciated

• 
  @angelobellini4666Ай бұрын

  buonasera, qualcuno ha un libretto di istruzione di questo apparato che può scannerizzarmi e mandarmi al mio indirizzo? Ringrazio anticipatamente. Angelo Bellini.

• 
  @Scif64Ай бұрын

  I had one of these many years ago. Such a great Transceiver. 73 de G0LQP

• 
  @scarone832 ай бұрын

  Please, make a video step by step how to connect icom to pc and then how install programs..... Please!! Please!!

• 
  @Gw0wvl2 ай бұрын

  Sorry I don't have the ICOM any more .

• 
  @scarone83Ай бұрын

  You need a usb cable, and other dispositive?

• 
  @jeffd98112 ай бұрын

  Hi, for the 3.5mm jack can one from an old parts cb be used ? Thx 73

• 
  @gtretroworld2 ай бұрын

  I thought that blue Vw transporter was mine there for a minute, good to see you back old boy.

• 
  @Gw0wvl2 ай бұрын

  We spent the weekend travelling around in the camper van and stopped of at Elan Valley 👍

• 
  @MM0IMC2 ай бұрын

  Brake testing route! 🤣

• 
  @Gw0wvl2 ай бұрын

  Shake test route 👍

• 
  @alanyoung93902 ай бұрын

  Hey you old dog ....I'm back on the radio .. Alan Robin lol

• 
  @Gw0wvl2 ай бұрын

  Hey Alan Matey ..... How's you these days ? ..... What band or bands you on ?

• 
  @Gw0wvl2 ай бұрын

  Drop me a P.M Alan matey .

• 
  @richard106d2 ай бұрын

  👂👍🏻

• 
  @TUCBER2 ай бұрын

  some one answer 2SC1969.. But where is this 2SC1969. on printed circuit? Thanks a lot. Berny

• 
  @TUCBER2 ай бұрын

  Hello from Grenoble France I'am Berny 81. I think that I use mike of my Lafayette 1200 but with antenna out. One answer to me at talk about 1969 broken; What is 1969 ? What you think about ? my stupidity.Regards. Bravo Tango

• 
  @TUCBER2 ай бұрын

  Hello from Grenoble France I'am Berny 81. I think that I use mike of my Lafayette 1200 but with antenna out. One answer to me at talk about 1969 broken; What is 1969 ? What you think about ? my stupidity.Regards. Bravo Tango

• 
  @TUCBER2 ай бұрын

  Hello from Grenoble France 'aI m Berny 81. I think that I use mike of my Lafayette 1200 but with out antenna. One answer to me at talk about 1969 brocke; What is 1969 ? What you think about ? my stupidity.Regards.

• 
  @vtradio2 ай бұрын

  Nice demo of the Icom IC-R70. Glad you were able to fix the poor receive. 73 Paul AA1SU

• 
  @Gw0wvl2 ай бұрын

  Many thanks!👍

• 
  @Watchman77-to3gl2 ай бұрын

  The Yagi is a beam antenna is that correct? The 5/8 is a omni antenna? Also are you running barefoot?

• 
  @NicksStuff2 ай бұрын

  £15!?

• 
  @DragosGheorghe-xt5py2 ай бұрын

  Hello, what model is your yagi ?

• 
  @wolfgangfisch81603 ай бұрын

  Was ist los hier.Sprechen wir kein Deutsch mehr.

• 
  @donlum91283 ай бұрын

  Blue Thunder from Tyler, Texas

• 
  @aureliusprimus3 ай бұрын

  Very fine : How many whiskies did you use and what for batteries (this radio n eeds 23 Ah minimum, is that right ? Have a nice day 😀

• 
  @stainlesssteel42603 ай бұрын

  My 756pro2 don't power on any solution

• 
  @stainlesssteel42603 ай бұрын

  My icom 756pro 2😢 won't power on

• 
  @DeepBlueWaves3 ай бұрын

  Bro, is that a Mazda Tribute? Looks just like mine :)

• 
  @Gw0wvl3 ай бұрын

  Vauxhall Astra 1.9 TDCI SRI

• 
  @14DFASniper3 ай бұрын

  That is fantastic!

• 
  @mrsus69434 ай бұрын

  My dad lost his a long time ago, it was his favorite one. He Loaned it to his friend and his friend gave him back the wrong radio. Where did you buy this, ive been wanting to buy one for him for his birthday

• 
  @Gw0wvl4 ай бұрын

  It was of eBay .... I no longer have this radio anymore , I decided to downsize all my CB a few years ago .

• 
  @wayneyates46674 ай бұрын

  how do I disconnect the anl system, other stations have to be very close to recieve

• 
  @Sidmi5utc4 ай бұрын

  Did you connect a line isolator at the radio end ?

• 
  @orazioscardace9115 ай бұрын

  Semplice e buona radio😊

• 
  @orazioscardace9115 ай бұрын

  Ottimo nb🙌

• 
  @DOIT-Retro5 ай бұрын

  I've been watching videos about the 891 and I've seen your vid here for a couple times. Great video!! I really enjoyed it. Good luck with your radio and antenna. All the best Marc... from West Virginia U.S. Cya

• 
  @Gw0wvl5 ай бұрын

  Glad you enjoyed it!

• 
  @martinryan50695 ай бұрын

  Sounds excellent

• 
  @conservative5995 ай бұрын

  Fantastic demonstration, the Icom 706MK2G in my Gas 2.4L 2007 Sonata NB can whack 20dB lower ignition noise, but not all the time, it needs some user threshold adjustment. Your excellent Video here is the ONLY real demonstration applicable to my Jewel of a TS-440-SAT radio I got on ebay, for $280 USD last March!!! I bought it from a merchant with tons of more expesive used ham equipment, many photos and honest that it has no dial light, and (still) doesn't transmit. But NO pesky PLL SonyBond cement caused PLL dots issue, but I am not chancing that going mobile and humidity causing issues. BUT I thought it did not have an NB feature at all, which would be great on 160m 22kHz interference at home. So I have it on 1795KHz AM Wide BW and the buzzing hum is S9 + 10dB, with ATT OUT. My 440 shows NO response at all, to pressing the NB button, but this is not ignition or injector noise, which you so aptly demonstrated. I heard the slight delay as the circuitry homes in on the noise level, and likely the AGC is responding to the noise reduction. No clicking was heard either. Hopefully the NB turn on wire is broken. I bought a used TS-520 NB board to add to my R599, which has even better crystal filters and with 10x all filter and audio caps, sounds very warm thru a B&O S-45 speaker! Thanks to the ebay aggregator site PicClick.com which I scoured for and immediately purchased every available 440 filters and accessories, and did the Blue White Dial LED mod very successfully. Also, since TX mode lights RED OK, but never shows any RF output, or increase in the 13.8V/2A Receiver current drain initially, now it hits 10A in TX, and the back heatsink gets hot because the FAN never kicks on. Going to DISCONNECT the main 13.8V wire to the PA board, AND reroute the Driver input coax to the SPARE jack on the rear panel, to check the Driver board output (if any) on a spectrum analyzer. No worries, Mate, I also bought a spare PA Board, It's RF transistors used on ebay, AND some imitation Toshiba finals that are well rated by CB Amplifier repair guys. Now I have all the filters, Voice Annunciator board, Serial Interfacing IC's and the front S Meter/Display LED mod is magnificent. The 440 also has an excellent Biquadratic OP AMP based AF Notch Filter, I thought didn't work - just turn the NOTCH control very slowly to find the notch. Better than my ICOMs', because it isn't DSP, nor LOCKED OUT in CW mode. You can tune out an adjacent CW or carrier signal very effectively, with the great 500Hz CW filter in or out! Go and look at the wonderful reviews on eham dot net, the most loved feature is NO MENUS, high 200W input, and excellent Kenwood sound from Bluetooth if plugged into the Earphones jack. Now you have given me something else very important to investigate, the apparently excellent Noise Blanker! 73.s from the USA, Hilary W4HDL

• 
  @Kenonharp5 ай бұрын

  Good demonstration. However, there are a number of SDRplay module models available with quite a large variation in price. Can you please tell me which model you are using? Also, would the basic RSP1B do the job? Thanks.

• 
  @lucifor35495 ай бұрын

  Why nobody explain the complete Way to do this on a FT 950? Is ist a classfied secred? So nobody have to know about. Thumb down for that.

• 
  @Kenonharp3 ай бұрын

  Exactly. He does not say how or where to take off the if

• 
  @anonymous_friend6 ай бұрын

  Can you elaborate on the setup of this please? More detail would be helpful

• 
  @Gw0wvl6 ай бұрын

  I no longer have this set up , I sold the 706 a few years ago .

• 
  @justinruth97296 ай бұрын

  800.tops if thebtubes are perfect and thats asking alot .. normaly 600-750 is sweet spot 2 572bs..had some flaws on then2100b butbwas decent amp

• 
  @justinruth97296 ай бұрын

  Because the bleed off voltage is still drain off whennu shit doen the amp ...so its very posible for the resistor to fail ass the vomtage is draining ...the part can brakedown,then go open ...happens alot actually..... Especially in bleeder circuits, one way to help insure the amp is safe is to make sure thwre are bleeders and always drain caps...inwich the bleeder circuit should do...thosnis why the resistor can fail even after shut off.... Beat of luck..73 from justin

• 
  @ivorbiggen95996 ай бұрын

  Looked everywhere for a 144/70 Transverter but no joy anywhere, unless I’m looking for the wrong item, maybe old hat now

• 
  @batfalcononyoutube6 ай бұрын

  Hi. I recently purchased a used FT 2000D, which the previous owner has made this mod, so I got a cable coming out of the back of the 2000, with an SMA connector at the end. I already have the RSP Duo, but I do not have a clue how the two units will work together. The IF from the 2000 travels through this cable to the one input of the RSP Duo, which is connected with the USB cable to my laptop. So far so good. What frequency shall I use on the RSP? The same as the 2000? Will this frequncy change as I change the frequency on the rig? For the moment I do not have the connecting cable from the Yaesu to the laptop. Any advice and explanation would be more than welcome. Thank you in advance for your time and answer, 73 de SV1SLB

• 
  @austieoutdoors97636 ай бұрын

  i have just watched this video as i have just bought one for portable and i was wondering as i have never tryed AM but just tryed it and its working great even got the states on there 73 from m7byf

• 
  @austieoutdoors97636 ай бұрын

  i usually use a icom 756 pro 3 but just bought the ts440 sat to take portable up ashhurst beacon by my house in the summer but i have had it on in the shack for the past two weeks and im loving it i all so had a kenwood mc60 desk mic so i wired that up to it and its getting better reports than my icom lol 73 great video from m7byf in west lancs

• 
  @Gw0wvl6 ай бұрын

  For an older radio the 440 takes some beating 👍👍👍

• 
  @MM0IMC6 ай бұрын

  Is the first amp a Chinese rip off of the Italian RM range? 🤔 I don't think the equivalent RM one which the Chinese copied would be any clearer.

• 
  @yo5pdw4396 ай бұрын

  antenna?

• 
  @Gw0wvl6 ай бұрын

  Sirio GPE-27 ... 5/8 wave vertical .

• 
  @yo5pdw4396 ай бұрын

  I buy one(ft-891) but i need your location...HI,very low noise

• 
  @paulsradiohacks6 ай бұрын

  That radio is like new! loved my old 440 but sold it to buy a 726R

• 
  @Gw0wvl6 ай бұрын

  It is like new both outside and inside , I've also got a spare as new front panel for it if this one ever gets damaged .

• 
  @CharlesBultez6 ай бұрын

  Good vidéo ! 👍

• 
  @MrMadhousedave6 ай бұрын

  Hey There Lovely conversion. I looked around and found 1 other tut but it involved cutting into the original wiring and this was a perfect solution. easy fitment of the socket and clean interface with the speaker. I will never understand why people mod radios or any electronics and just hack and butcher wires and switches into place. if it made it look better externally or if it made the radio more functional i can understand that. personally your method for this is 100 percent the cleanest and best way. Cheers Dave Sydney Australia