Пікірлер

• 
  @ramavtar892072 ай бұрын

  👍🇮🇳🕉️🙏

• 
  @MainADMlN3 ай бұрын

  As a school-trained licensed and certified HVAC technician. This is working the easy lazy way, which sooner or later catches up to you. Referring to the refrigerant as "Freon" gave me the hives. No deburring? Lazy. The bending is so badly made it kinked the tube, which produces flow turbulence. Not protecting the filter from the brazing heat? Nice way to possibly damaging it. Having nitrogen and planning on using it, but not flowing it during the brazing... oh boy. Carbonization in the inside. That filter might need replacement soon again. But if you only didn't refer to the gas as "freon"....

• 
  @Freonleon3 ай бұрын

  Hack, using wire strippers to cut the cap tube, and drier.

• 
  @YESHUASAVES777YYY10 ай бұрын

  My dryer filter is very cold any ideas ?

• 
  @Cholla-Ranch Жыл бұрын

  Very helpful. Thank you.

• 
  @kamalabbady6778 Жыл бұрын

  This is r600a its a flammable please don't braze it, this guy will get you killed.

• 
  @peniasnyirenda8095 Жыл бұрын

  Nice job my fellow technician

• 
  @syedali10772 жыл бұрын

  Brazing job is poor

• 
  @patricioaguayo90882 жыл бұрын

  How about dryer on any reefer unit. Thank you

• 
  @markspc13 жыл бұрын

  Your solder is bubbling up, too hot frame.

• 
  @kcengiz3633 жыл бұрын

  How do you understand you got problem in the filter dryer?

• 
  @davidcromer2675 Жыл бұрын

  95% of the time that’s the clog if you have blockage. There are ways to test. You are going to replace that anyway during a service where you are going into a sealed system.

• 
  @pavansampuri64323 жыл бұрын

  Induction brazing better than this

• 
  @reefermadd.22043 жыл бұрын

  Shop mentality . That was the lazy way of doing that.

• 
  @hornzhou17353 жыл бұрын

  What kind of solder material are you using to solder?

• 
  @engineerahmad63753 жыл бұрын

  I have a problem. When I try to move a refrigerator from one place to another on the backside the oil inside the compressor return back to the filter and damages it. Is that video help me to avoid that?. Any other solutions could help to prevent the oil from going out to the filter and damage it like a one-way valve or other ideas. Please suggest me solutions. Thank you.

• 
  @jd57873 жыл бұрын

  Just wondering : why does the filter need to be changed when replacing a compressor? Is it something that can be done in stages? (change filter on day 1 and compressor on day 2?). Thanks

• 
  @vihayster3 жыл бұрын

  filter dryer is there for catching moisture, chemicals and copper oxides created during brazing process (because they don't use dry nitrogen at time of brazing). After years of work when you change compressor that filter is almost clogged out and needs to be replaced. If you don't replace it, it may work few years OR only few weeks before gets clogged. When you install new compressor you create even more oxides that have to be filtered. Both compressor and filter should be brazed at the same time so the system is sealed quickly to prevent moisture getting in. New compressors and filters comes with sealed both ends so compressor oils (which very often are hygroscopic) and filter's desiccants are protected until installation time.

• 
  @jd57873 жыл бұрын

  @@vihayster thank you! Much appreciated :)

• 
  @Laurel-Crowned3 жыл бұрын

  Thank you for showing to cut the new dryer ends nobody else showed that part.

• 
  @johnflanagan41034 жыл бұрын

  No nitrogen purge while brazing. What a mess.That cap tube will plug up.😨😳

• 
  @vihayster3 жыл бұрын

  yeah...seems to be new normal. I haven't seen any videos with nitro in use during brazing refrigerator components. I think everybody assume that filter will catch everything, lol

• 
  @christopher61472 жыл бұрын

  @@vihayster I haven’t seen any either. strange

• 
  @Skoalman86854 жыл бұрын

  You kinked the pipe and then didnt even talk about pulling a vacuum lol.

• 
  @robgraham12044 жыл бұрын

  That pipe is kinked