Why is this an acceptable job? It's not good looking at all
@KaminJanob-ko9vt9 ай бұрын
Очен.хорошо.спасиба
@KaminJanob-ko9vt9 ай бұрын
Хорошо
@girmadimtsu2119 ай бұрын
I am from ethiopian GUTTER warker
@girmadimtsu2119 ай бұрын
Hi brother one cution aw mach machin getter
@livingaboard9 ай бұрын
That is an outside corner. Not an inside corner as your video states
@jddeefo10229 ай бұрын
8hrs later ya got 2 corners done.
@dalethompson695210 ай бұрын
I can’t see anyone on the job taking that much time to make an outside corner.
@michaelpost735211 ай бұрын
So, how do you make the template?
@ketrinkiss800 Жыл бұрын
good but no nice
@YThatesTRUTH Жыл бұрын
I'm starting a gutter gig tmr and probably only have the job tmr if I did this.
@georgebrugh7822 Жыл бұрын
40 years still using Pop rivets. Please stop using that tinners hammer, the paint never matches
@b.w.seavestroughwindowclea581 Жыл бұрын
Terrible job...PERIOD!
@audio_video1155 Жыл бұрын
Where do u get the template
@2point2 Жыл бұрын
Love the funky ass flea bass
@rupindergill24482 жыл бұрын
Please upload video for inside cornners. By mistake, it is outside corner video but should show inside video. You are the BEST. Title says inside video but it shows outside corner video
@Phoenixrising83132 жыл бұрын
Ahhh you dented the outside corner no good throw it out lol.
@johnmcook12 жыл бұрын
@8:16 DENTED DENTS IT AT @7:43
@rgill34172 жыл бұрын
This was the best video. Could you please upload more videos about 30 degree slope corners and some other difficult corners and more tips about gutter jobs
@johnsmit52182 жыл бұрын
😱
@justinmccalligan94272 жыл бұрын
For all of you who have approved of hand tabbing corners like this it doesn’t say much for the quality you deliver. The man literally just put numerous dents into the face of the gutter and that’s building it on the ground with full access to any angle with any tool. Elementary is an understatement.
@zztop85922 жыл бұрын
I thought this video was for inside corner. LOL
@yonusakbary96092 жыл бұрын
sir, this is the same video as the outside corner. Can you please upload an inside corner video?
@aedgvv60953 жыл бұрын
how do i make a corner where one slide slopes upward?
@saveriodipoce22012 жыл бұрын
That takes a lot of experience.Ciao from Italy
@georgebrugh7822 Жыл бұрын
You have to make a template, witch will show it will never be perfect
@paulaguilar50413 жыл бұрын
Omg. That was terrible. Do not copy this pattern. I am a 32 year Sheetmetal worker. I would be embarrassed to have made this video. The proper way is. Most gutters are 4” wide. The back of gutter is a straight cut, not angled like these idiots did. Then the bottom is a 45 degree cut , then the front is the remainder from the 45 degree cut to the 4” cut from the back of gutter. That hole bit about dollying over extra metal on the face of the gutter hurt my eyeballs. Atrocious!
@kylethomaszelesnick15173 жыл бұрын
Lol did you just use a pen 😂
@kylethomaszelesnick15173 жыл бұрын
And a philliphs screw 😂😂
@rreasons643 жыл бұрын
Spray paint the corners ??? In the sunlight you will see the overspray on the gutters especially if you're talking about black or brown or bronze.... We never spray paint anything
@rreasons643 жыл бұрын
That looks like shit
@israelc77243 жыл бұрын
Kids do not try this at home
@pj37173 жыл бұрын
Looks like shit LOL
@snakedoc1043 жыл бұрын
If I do this my boss would shoot at me
@experienceprecision54063 жыл бұрын
Do you need a pattern first. Got it
@pj37173 жыл бұрын
When I see these so called professionals put metal roof on top of old shingles I just want to knock you people out
@jasonbruns19763 жыл бұрын
Good video, i like the slat cut inbottom back mitre that locks them together. Only thing i wld change is to not have the extra length tab on bottom and no screws on bottom either
@ramizbutkovic96423 жыл бұрын
you have no clue how it should be done.
@cory16753 жыл бұрын
Box mitres way faster . I would never put a screw thru the bottom
@TheOriginalPaulGilpin3 жыл бұрын
Just because you can doesn't mean you should. For a few measly dollars, you could buy a corner piece. So few people take pride in their work and the finished product given to a customer.
@serge.crispino4183 жыл бұрын
You are joking - right ?? Definitely untidy and NOT the way to form a corner, this would not be acceptable in my neck of the woods.
@nanterey883 жыл бұрын
If you fold the sheet inside and never cut it you have best result the rivet and the joints never seen outside.
@brandontarr54184 жыл бұрын
Jesus, what did I just watch?
@carolkinsey10444 жыл бұрын
What is the name of the back ground music
@aaronlaplante21984 жыл бұрын
Where do you buy the patterns?
@shaunkimpel51764 жыл бұрын
Butcher
@bossdog14804 жыл бұрын
For a start that's an OUTSIDE corner. Did you ever make a mess of that? You dented the hell out of it. Practise makes perfect.
@bossdog14804 жыл бұрын
Rough as guts. I thought it was going to be good when you showed the template. I hope you don't actually put those on customers roofs. I learned how to do this properly when I was 16, and it's definitely NOT like that.
@amilli0924 жыл бұрын
That looks pretty good and good instructions why is there so much hate?
@dammyb.44384 жыл бұрын
How do you do this corner 30 feet above ground level?
@jhonembarnace43154 жыл бұрын
No good
@clist94064 жыл бұрын
You teach people how to be hacks ? Why not teach them correctly and double fold and pinch like HVAC ducting. Much cleaner and professional results
@clist94064 жыл бұрын
If it was my house you'd be taking that mess off and escorted off the property. What a joke
Пікірлер
Why is this an acceptable job? It's not good looking at all
Очен.хорошо.спасиба
Хорошо
I am from ethiopian GUTTER warker
Hi brother one cution aw mach machin getter
That is an outside corner. Not an inside corner as your video states
8hrs later ya got 2 corners done.
I can’t see anyone on the job taking that much time to make an outside corner.
So, how do you make the template?
good but no nice
I'm starting a gutter gig tmr and probably only have the job tmr if I did this.
40 years still using Pop rivets. Please stop using that tinners hammer, the paint never matches
Terrible job...PERIOD!
Where do u get the template
Love the funky ass flea bass
Please upload video for inside cornners. By mistake, it is outside corner video but should show inside video. You are the BEST. Title says inside video but it shows outside corner video
Ahhh you dented the outside corner no good throw it out lol.
@8:16 DENTED DENTS IT AT @7:43
This was the best video. Could you please upload more videos about 30 degree slope corners and some other difficult corners and more tips about gutter jobs
😱
For all of you who have approved of hand tabbing corners like this it doesn’t say much for the quality you deliver. The man literally just put numerous dents into the face of the gutter and that’s building it on the ground with full access to any angle with any tool. Elementary is an understatement.
I thought this video was for inside corner. LOL
sir, this is the same video as the outside corner. Can you please upload an inside corner video?
how do i make a corner where one slide slopes upward?
That takes a lot of experience.Ciao from Italy
You have to make a template, witch will show it will never be perfect
Omg. That was terrible. Do not copy this pattern. I am a 32 year Sheetmetal worker. I would be embarrassed to have made this video. The proper way is. Most gutters are 4” wide. The back of gutter is a straight cut, not angled like these idiots did. Then the bottom is a 45 degree cut , then the front is the remainder from the 45 degree cut to the 4” cut from the back of gutter. That hole bit about dollying over extra metal on the face of the gutter hurt my eyeballs. Atrocious!
Lol did you just use a pen 😂
And a philliphs screw 😂😂
Spray paint the corners ??? In the sunlight you will see the overspray on the gutters especially if you're talking about black or brown or bronze.... We never spray paint anything
That looks like shit
Kids do not try this at home
Looks like shit LOL
If I do this my boss would shoot at me
Do you need a pattern first. Got it
When I see these so called professionals put metal roof on top of old shingles I just want to knock you people out
Good video, i like the slat cut inbottom back mitre that locks them together. Only thing i wld change is to not have the extra length tab on bottom and no screws on bottom either
you have no clue how it should be done.
Box mitres way faster . I would never put a screw thru the bottom
Just because you can doesn't mean you should. For a few measly dollars, you could buy a corner piece. So few people take pride in their work and the finished product given to a customer.
You are joking - right ?? Definitely untidy and NOT the way to form a corner, this would not be acceptable in my neck of the woods.
If you fold the sheet inside and never cut it you have best result the rivet and the joints never seen outside.
Jesus, what did I just watch?
What is the name of the back ground music
Where do you buy the patterns?
Butcher
For a start that's an OUTSIDE corner. Did you ever make a mess of that? You dented the hell out of it. Practise makes perfect.
Rough as guts. I thought it was going to be good when you showed the template. I hope you don't actually put those on customers roofs. I learned how to do this properly when I was 16, and it's definitely NOT like that.
That looks pretty good and good instructions why is there so much hate?
How do you do this corner 30 feet above ground level?
No good
You teach people how to be hacks ? Why not teach them correctly and double fold and pinch like HVAC ducting. Much cleaner and professional results
If it was my house you'd be taking that mess off and escorted off the property. What a joke