Step-by-step installation instructions for weather seals and brush seals on hangar doors, bifold and hydraulic hangar doors, barn doors and sectional steel doors.
Are the brush strips intended to keep rodents out? Any tips on a reverse curtain installation? [roll on the outside]. Mine came with what looks like a 6” seal strip for the header. No instructions from manufacturer for a reverse curtain installation. A video on that would be good. Thanks
@ariandaddy4 ай бұрын
How would you go about putting this on the Hebal (Autoclaved Aerated Concrete) walls?
@paulcooper5344 ай бұрын
Hi, Thanks for the video. Is that the Medium Duty brush or the Heavy Duty you installed? Thanks!
@clintonmclimore83705 ай бұрын
How do know what angle I need.
@bsrcat16 ай бұрын
Maybe you should cycle the doors so we can see where the brushes look like and lay 🤷. I know that would interest me.
@user-db8ig6ev2m9 ай бұрын
will it help to keep mice out
@darrenperea703710 ай бұрын
Do you have instructions for installment on a one panel door not a roll-up door
@darrenperea703710 ай бұрын
We're trying to install this on a single panel garage door and having issues with the top brush preventing the garage door from opening. We trim down the bristles thinking that that would work but it's not helping it's preventing the door from opening do you have any ideas?
@queensryche.11 ай бұрын
claro y conciso. gracias.
@turdferguson1021 Жыл бұрын
Instructions unclear. Arm stuck in roll up door.
@14cmdavis Жыл бұрын
Ok, the moving camera is really annoying, can you just hold it still please.
@NewEnglandRefugee Жыл бұрын
I have an odd question. I have frequent gusts of wind in my area, and my roll-up doors sometimes bang around almost constantly for hours on end. Would these quiet my doors down at all?
@jasonhoffe5124 Жыл бұрын
Yes, the brush seals will put some pressure on the door and reduce the vibration and rattling sound.
@shayalkobi83 Жыл бұрын
What about water/rain? Does it prevent it?
@jasonhoffe5124 Жыл бұрын
The brush seals aren't water-proof, but will definitely help keep a majority of the water/rain out. Make sure the exterior ground slopes away from the sliding barn door too.
@cruzmacias9658 Жыл бұрын
Shitty video
@NYTROeast Жыл бұрын
What kind of wear do these brushes make on the doors down the road? Do they wear the finish off?
@jasonhoffe5124 Жыл бұрын
The nylon brush will not affect the finish of the door.
@markfrye9178 Жыл бұрын
Do the brushes have a memory? As in stuck in a high or low position in this application?
@jasonhoffe5124 Жыл бұрын
The nylon brush has low memory compared to other bristle types, but will take form over time. Even if the brush forms to high/low ribs it will keep a consistant pressure on the door creating a great seal. If needed the nylon brush can be brought back to it's original form with low heat or warm water.
@peterbarlow8912 Жыл бұрын
Never seen a rolling barn door with trolley bracket on the inside face. Self tapping screws drill out to much wood to hold well in wood. Have used brush seals on rolling doors before. On wood doors I apply wood strips on the inside face around the edges after hanging to close the gap. I also progressively shim the track out of parallel to the facade and adjust the trolleys on their brackets back to parallel. That way it pulls away from the stops on opening just like an overhead door without friction.
@jasonhoffe5124 Жыл бұрын
With the trolley bracket on the exterior side of the door the trolley wheel can be ajusted in/out to ride on the aluminum track of the brush seal holder. Pictures of this detail can be found on the website. We have had good sucess with our self-tapping fastners holding solidly in wood positioned 1ft centers.
@Hangs4Fun Жыл бұрын
I see Jacor isn't responding to any questions, but I will try any way. I upgraded my 12x12 and 8x8 rollup doors to have the "Dutch Corners" or 45° corners. Would I use the side pieces or the top pieces? Also in the video he didn't show how best to do the corners where the pieces come together, which gets a little more challenging with my 45°. I assume some type of 22.5° bevel, but not clear on how they come together even for a regular 90° corner. I assume since he does the top first, that the side brushes metal portion stops at the brush, but it could also be best to remove the brush strands where the side meets up so the metal frames can touch each other??
@Hangs4Fun Жыл бұрын
5:36 I took a screen shot at this point and zoomed in to his corner. I can see why it wasn't mentioned in the video, the corner is sloppy AND he changes the last 2 feet of the side to come out to the top piece which creates a huge gap on the upper ribs. I really think you should take the time to shop how the corners are done (with a proper install though). I already bought 2" kits for my 12x12 and 8x8, so I'm installing them either way, but I will look elsewhere for proper installation of the corners. The whole point of investing money on these is to keep out dust, insects, and help with heating and cooling. For me, especially keeping hot air out (sun hit the door, hot air rises, and gets channeled in through the huge gaps at the tops of the rollup doors. So I'm not going install it this way and still end with huge gaps at the side top corners.
@jasonhoffe5124 Жыл бұрын
For Dutch Corners using the 45deg brush works best. Just make sure you order the correct brush seal kit size for the vertical side + dutch corner. Our website (jacorinc.com) has pics showing dutch corners. Look for the scrolling pics at the bottom of the brush seal kits product page or in Brush Seals -> Applications -> Roll-up Doors. The top straight brush gets installed first and the 45deg side brush butts against the top brush closing off the corner. The straight top brush will be just behind the 45deg side brush sealing off the corner for both dutch and 90deg corners.
@Hangs4Fun Жыл бұрын
@@jasonhoffe5124 thank you, I already have the kits. I guess I need to order some extra 45 pieces. I will check out the site and see what I need to do to make up the diff. I will have some left over straight pieces I guess too
@frankq54732 жыл бұрын
could it be installed from the inside of the garage?
@yaniomiyah26552 жыл бұрын
Good
@patrickpatrick91322 жыл бұрын
Unable to hear very well. Good front what I could hear.
@jasonhoffe51242 жыл бұрын
We have an updated barn door installation video with better sound and more details. kzread.info/dash/bejne/qZmfus-mYKu_YLw.html
@sherrylkeith96952 жыл бұрын
Thousands of lifetime projects with Woodglut plans.
@risinbison11062 жыл бұрын
I live in an extreme climate with hot, humid summers and bitterly cold snowy winters. How well does this product stand up to these conditions and what life expectancy can I get out of a set.
@jasonhoffe5124 Жыл бұрын
The brush seals will make a significant difference with air infiltration reducing the cost of heating and cooling along with keeping bugs, pests, debris out. The high quality nylon brush has very good bend recovery. Life expectancy depends on daily use.
@kCI2512 жыл бұрын
One hell of a nice beer collection!
@jasonhoffe51242 жыл бұрын
We are in Wisconsin!
@johnfisk84072 жыл бұрын
what would you recommend , we have bypass sliding barn door style at our hangar/shop one door is rarely ever opened, but we want it operable if we need to, also there is nearly a 6-8 inch gap between the doors, and the bottom of the doors hangs into a trench, no rollers, out side is corrugated but vertical. the inside door is the one used most frequently?
@tonysimko112 жыл бұрын
Thanks for this do you know who made this door I’m trying to install one now. Much appreciated!
@jasonhoffe51242 жыл бұрын
Not sure who the bifold door mfg was on this installation.
@MrGsamick2 жыл бұрын
I purchased this and installed it. It works just as planned. From the inside of my shed, I no longer have light coming in from the sides and top. I recommend buying other screws vs. using what is supplied. I used #10 Bonded Sealing Drill Screws - 1 3/4". I just used the same screws that the contractor used to put together my steel shed. Very happy with the final product.
@jaijason81502 жыл бұрын
Great vid. All the information I need to order and install.
@mrglindsay33 жыл бұрын
Very clean install product! I will order soon!
@kryptoniteee3 жыл бұрын
This is amazing. I want this but I am in Great Britain.
@MatthewGertsch3 жыл бұрын
Great work guys
@AA-kf7uf3 жыл бұрын
Where can I purchase the door? thank you!
@jasonhoffe3 жыл бұрын
We just supply the weather seals and hardware. There are a numerous bifold door mfgs out there.
@quinnjim4 жыл бұрын
I have a 44' door very similar to this. I bought the rubber and all mounting hardware. I sanded down the metal, primed and painted it. How much do you usually charge to install the seal?
@doodleydude78334 жыл бұрын
i came here just want to see the roller mechanism tho. thanks
@johnthorp45464 жыл бұрын
Always appreciate your videos! Great detail and craftsmanship. John, Field Maintance, Millard Airport. 😎
@jasonhoffe51244 жыл бұрын
Thanks John!
@adamaustin33734 жыл бұрын
what is the best thing to use for sealing the bottom of the barn door?
@GaryStango3 жыл бұрын
evidently, SILENCE is the answer
@jasonhoffe51243 жыл бұрын
HI Adam, Sorry I missed this comment. The straight brush fastened to the exterior bottom edge of the door works great. We have a new video posted that shows this detail.
@adamaustin33734 жыл бұрын
what is the best thing to seal the bottom of a sliding barn door with?
@jasonhoffe51244 жыл бұрын
Our nylon brush seal with a straight holder works great when fastened to the exterior bottom edge of the door.
@johnthorp45465 жыл бұрын
Great video and professional work! Thank you Millard Airport Field Maintance!
Пікірлер
Отличное решение для герметизации стыка)
Good video thank you
Are the brush strips intended to keep rodents out? Any tips on a reverse curtain installation? [roll on the outside]. Mine came with what looks like a 6” seal strip for the header. No instructions from manufacturer for a reverse curtain installation. A video on that would be good. Thanks
How would you go about putting this on the Hebal (Autoclaved Aerated Concrete) walls?
Hi, Thanks for the video. Is that the Medium Duty brush or the Heavy Duty you installed? Thanks!
How do know what angle I need.
Maybe you should cycle the doors so we can see where the brushes look like and lay 🤷. I know that would interest me.
will it help to keep mice out
Do you have instructions for installment on a one panel door not a roll-up door
We're trying to install this on a single panel garage door and having issues with the top brush preventing the garage door from opening. We trim down the bristles thinking that that would work but it's not helping it's preventing the door from opening do you have any ideas?
claro y conciso. gracias.
Instructions unclear. Arm stuck in roll up door.
Ok, the moving camera is really annoying, can you just hold it still please.
I have an odd question. I have frequent gusts of wind in my area, and my roll-up doors sometimes bang around almost constantly for hours on end. Would these quiet my doors down at all?
Yes, the brush seals will put some pressure on the door and reduce the vibration and rattling sound.
What about water/rain? Does it prevent it?
The brush seals aren't water-proof, but will definitely help keep a majority of the water/rain out. Make sure the exterior ground slopes away from the sliding barn door too.
Shitty video
What kind of wear do these brushes make on the doors down the road? Do they wear the finish off?
The nylon brush will not affect the finish of the door.
Do the brushes have a memory? As in stuck in a high or low position in this application?
The nylon brush has low memory compared to other bristle types, but will take form over time. Even if the brush forms to high/low ribs it will keep a consistant pressure on the door creating a great seal. If needed the nylon brush can be brought back to it's original form with low heat or warm water.
Never seen a rolling barn door with trolley bracket on the inside face. Self tapping screws drill out to much wood to hold well in wood. Have used brush seals on rolling doors before. On wood doors I apply wood strips on the inside face around the edges after hanging to close the gap. I also progressively shim the track out of parallel to the facade and adjust the trolleys on their brackets back to parallel. That way it pulls away from the stops on opening just like an overhead door without friction.
With the trolley bracket on the exterior side of the door the trolley wheel can be ajusted in/out to ride on the aluminum track of the brush seal holder. Pictures of this detail can be found on the website. We have had good sucess with our self-tapping fastners holding solidly in wood positioned 1ft centers.
I see Jacor isn't responding to any questions, but I will try any way. I upgraded my 12x12 and 8x8 rollup doors to have the "Dutch Corners" or 45° corners. Would I use the side pieces or the top pieces? Also in the video he didn't show how best to do the corners where the pieces come together, which gets a little more challenging with my 45°. I assume some type of 22.5° bevel, but not clear on how they come together even for a regular 90° corner. I assume since he does the top first, that the side brushes metal portion stops at the brush, but it could also be best to remove the brush strands where the side meets up so the metal frames can touch each other??
5:36 I took a screen shot at this point and zoomed in to his corner. I can see why it wasn't mentioned in the video, the corner is sloppy AND he changes the last 2 feet of the side to come out to the top piece which creates a huge gap on the upper ribs. I really think you should take the time to shop how the corners are done (with a proper install though). I already bought 2" kits for my 12x12 and 8x8, so I'm installing them either way, but I will look elsewhere for proper installation of the corners. The whole point of investing money on these is to keep out dust, insects, and help with heating and cooling. For me, especially keeping hot air out (sun hit the door, hot air rises, and gets channeled in through the huge gaps at the tops of the rollup doors. So I'm not going install it this way and still end with huge gaps at the side top corners.
For Dutch Corners using the 45deg brush works best. Just make sure you order the correct brush seal kit size for the vertical side + dutch corner. Our website (jacorinc.com) has pics showing dutch corners. Look for the scrolling pics at the bottom of the brush seal kits product page or in Brush Seals -> Applications -> Roll-up Doors. The top straight brush gets installed first and the 45deg side brush butts against the top brush closing off the corner. The straight top brush will be just behind the 45deg side brush sealing off the corner for both dutch and 90deg corners.
@@jasonhoffe5124 thank you, I already have the kits. I guess I need to order some extra 45 pieces. I will check out the site and see what I need to do to make up the diff. I will have some left over straight pieces I guess too
could it be installed from the inside of the garage?
Good
Unable to hear very well. Good front what I could hear.
We have an updated barn door installation video with better sound and more details. kzread.info/dash/bejne/qZmfus-mYKu_YLw.html
Thousands of lifetime projects with Woodglut plans.
I live in an extreme climate with hot, humid summers and bitterly cold snowy winters. How well does this product stand up to these conditions and what life expectancy can I get out of a set.
The brush seals will make a significant difference with air infiltration reducing the cost of heating and cooling along with keeping bugs, pests, debris out. The high quality nylon brush has very good bend recovery. Life expectancy depends on daily use.
One hell of a nice beer collection!
We are in Wisconsin!
what would you recommend , we have bypass sliding barn door style at our hangar/shop one door is rarely ever opened, but we want it operable if we need to, also there is nearly a 6-8 inch gap between the doors, and the bottom of the doors hangs into a trench, no rollers, out side is corrugated but vertical. the inside door is the one used most frequently?
Thanks for this do you know who made this door I’m trying to install one now. Much appreciated!
Not sure who the bifold door mfg was on this installation.
I purchased this and installed it. It works just as planned. From the inside of my shed, I no longer have light coming in from the sides and top. I recommend buying other screws vs. using what is supplied. I used #10 Bonded Sealing Drill Screws - 1 3/4". I just used the same screws that the contractor used to put together my steel shed. Very happy with the final product.
Great vid. All the information I need to order and install.
Very clean install product! I will order soon!
This is amazing. I want this but I am in Great Britain.
Great work guys
Where can I purchase the door? thank you!
We just supply the weather seals and hardware. There are a numerous bifold door mfgs out there.
I have a 44' door very similar to this. I bought the rubber and all mounting hardware. I sanded down the metal, primed and painted it. How much do you usually charge to install the seal?
i came here just want to see the roller mechanism tho. thanks
Always appreciate your videos! Great detail and craftsmanship. John, Field Maintance, Millard Airport. 😎
Thanks John!
what is the best thing to use for sealing the bottom of the barn door?
evidently, SILENCE is the answer
HI Adam, Sorry I missed this comment. The straight brush fastened to the exterior bottom edge of the door works great. We have a new video posted that shows this detail.
what is the best thing to seal the bottom of a sliding barn door with?
Our nylon brush seal with a straight holder works great when fastened to the exterior bottom edge of the door.
Great video and professional work! Thank you Millard Airport Field Maintance!