Thank you for the video. Our brew switch stopped working, I'm going to use this video to troubleshoot this. This is a godsend! Thank you for posting
@francocalcagni932328 күн бұрын
I know this is an old post and you haven't made any videos in a while, making it on YT is not an easy gig. You give good information....BUT you repeat too much. This 24 minute video could have been a third, about 8 minutes and had the same relevant information. If ever you do more in the future, edit the repetitiveness. Also, not just you, but others that do a lot of the 1 handed stuff in front of the camera, is frustrating to watch. Otherwise, you have subscribers, views and many videos, so you have done more than a multitude of people that try to make it on YT. I don't know the exact numbers but for every successful YTuber, many have failed. Good luck if you continue on.
@tannerwest6823Ай бұрын
Do you work with Silva Brothers?
@tannerwest6823Ай бұрын
Have you got any of the Ridgid drawers yet?
@74567justinАй бұрын
Thank you!! I actually just needed to know how to safely remove that top pan to access the switches.
@nzodenАй бұрын
This review is meh
@IppiopaidFEEDBACKАй бұрын
Just picked this up from Home Depot (floor display) for $19. The clearance sticker said $95 down from $189. But it has been sitting on clearance since 10/23 and it’s now 07/24 I guess it’s been going down for the past 10 months. The store just didn’t keep up with the price tag, but thankfully they sold me the floor display because they were no more in stock at that store. Got home put a battery in it and thought maybe it was a dud! But then I realize you had to press the safety bar with the trigger at the same time. Worked extremely well, better than the Friskers manual has tremors work. Plus for $19 even if they didn’t work well I couldn’t complain.
@speedmaster001Ай бұрын
Your dog is also heavy at work. He understood the mission.
@tuberocker69Ай бұрын
Just got a set of wcs 3 points for my ms261cm. Couldn't be happier. Glad to see you enjoying yours. How have they held up?
@miguelquazar8832 ай бұрын
Just put a shim/spacer in there. These things shouldn't have these problems. For the money this sht shouldn't be happening.
@nofascists2 ай бұрын
K!
@stevesniadecki16782 ай бұрын
Hi, I’m having difficulty testing whether the led is bad, or if the input is bad from thermostat. What voltage should I be getting at the wiring harness the led plugs into. I have a 120/240 model cwtf35
@menajemh2 ай бұрын
thanks for the vid, helped me decide to go get the set of this, i'm so happy I found your video. was looking for a system to organize my tools and your review is very detailed with the improvements and comparison to other brands. also this could make some nice hard boxes to protect expensive radio equipment in transportation, just add some foam or cushion material. 73 from KD2OVM
@JoshNoss2 ай бұрын
They look ridiculous! And whats the point of the little mini spike bolted onto the absurdly big one? What purpose does it serve? Shame I cant get the stock 572 outer felling dawg and this is what I get in a search looking for some.
@Peaceisokman2 ай бұрын
LoL, I like when you said unplug the machine, I was a appliance tech for years, And I was getting shock all the time, : )
@sydneykillian36853 ай бұрын
What do you do or did do for a living?
@Buddy-po4hv3 ай бұрын
Some bits here and some bits there 🤣
@jaredanderson20093 ай бұрын
The classic B&D “dog dick in the dirt”
@kbittorf3353 ай бұрын
Nice comparison! I have an original 550xpg and love the heated handles in winter. 2017 build and I have not had any issues. But I run minimum 40:1 ethanol free 91 octane. My only dislike is the outboard clutch, do not forget to disengage the chain brake before removing the clutch cover! PITA when in the woods. Yes, an addict. My only husky and one of 7 that I own.
@diver2913 ай бұрын
Great review! Thanks
@TribeOfJudah_124 ай бұрын
Nice nail gun
@ucitymetalhead4 ай бұрын
I definitely want to get the new base box and drawer box but i use the original box as a seat and i wonder if the 2.0 will hold me or not.
@stevesniadecki16784 ай бұрын
Hi, am rebuilding one of these and I believe it’s leaking from the tank seal, so I have that on order, when taking it apart I took a pic of wires but it looks like the blanket Warmer had only one wire connected. Where does the other one go?
@waxyspore39464 ай бұрын
I’m just here for the coffee and donuts. Black with a teaspoon of sawdust pls.
@taylorsciame154 ай бұрын
I have this same exact model that I am currently trying to fix. Ive gone through hours of troublshoot. Got this for $50 at thrift store so dont know its history. To this point i replaced one brass water line that had a hole in it. And ive replaced the bug nut on top of the flow control on the back because the previous nut was cracked open (almost looked as though someone may have dropped it). After replacing these obvious things then i proceeded to troubleshoot the operation of the machine. Putting water into the top I wanted to make sure the tank was full so it could heat. Well during this process i put too much water in and water started pouring down to the bottom. I thought from previous forums i found that if i overflowed it then remainder would just come out theough the spray head. Well i was wrong which i later found out the silicone seal to the tank wasnt sealed properly. Currently it almost appears as though the top of the tank where it is bolted to the top looks warped a little bit. Not sure if it is supoosed to be flat or if its just warped. Hopefully not because i dont want to accidentally overfill it in the future and have it leak again. Ill address the leak if i can get the machine working. I have now gone through a series of testing continuity at alot of points to find my issue. I currently cant get the brewing process to start. The heating element comes on and heats the water to close to 200 degrees (i checked with a thermometer) but the water never boils up through yhe tube into the spray head through the filter tray. Was hoping maybe you had some advice for the leak spot and if you think that top could have been warped and if you know why i cant get brewing to start. Thank you
@taylorsciame154 ай бұрын
So I disconnected the spray head tube to see if there was buildup and seems to be water going through okay. Maybe my syphon gasket wasn't connected properly not allowing vapor.pressure from boiling to allow pass through to the brew cup
@taylorsciame154 ай бұрын
Update so my tank cover was warped and welded screws on tank were bent outwards preventing the cover from coming off. So I had to put the nuts on and bang the screws back so I could take the lid off. When I did I also discovered a big hole in the coil. So far this thing had 1 hole in a brass line that goes to the solenoid and coil , the flow regulator had a big hole in it and now the coil has a big hole in it and the cover was extremely warped. I'm sensing this thing had a major failure. I'm tempted to now replace the coil, new gaskets and new cover and see what it does but I'm also nervous it will fail again. Maybe that first hole created bad pressure and just created a chain reaction eventually in other points ?
@taylorsciame154 ай бұрын
Do after ally parts came in and putting everything back together, the water heater heats the water and it clicks off automatically but once it's heated and I hit the start button it still wont brew. Any idea what could still be the problem?
@Cervidator4 ай бұрын
Have you checked out the West Coast saws felling dogs? Next level stuff!
@williamlewis43795 ай бұрын
Thanks for making this video, very helpful! On the Neiko security bit set, how did those work out for you? Thanks
@MrFreeknassty5 ай бұрын
You can get to bar adjuster on the 562xp ?
@MrFreeknassty5 ай бұрын
I just emailed to get a price
@manueljaimes33325 ай бұрын
Mierda!!! Yo también tengo el mismo problema 👀soy adicto y fanático de las sierras motorizada 2t😂
@Johnny-vu7db5 ай бұрын
How is the water level in the boiler determined? I have one that fills and keeps running and overflowing. There must be a sensor to trigger the fill valve?
@n3qdz5 ай бұрын
Mine has the same issue that I’m currently dealing with. 1st problem to look at it is the water solenoid. Sometimes it may not seal after you brew or just sitting there. If you have a instant hot water dispenser, you can have a leak in the circuit that is still feeding the boiler volume. When you do a boiler feed for the first time you have to do it when the machine is off. Then fill up the boiler till water comes out. Then turn on the machine and press brew you should be go to go
@gutal855 ай бұрын
hey. 3 days ago i buy 550xp. now i have question. i this normal? here i uploaded video on youtube. kzread.infoJ4-r6W1gxOw?si=ZwhiueXadB3P4Swj
@recyclespinning98395 ай бұрын
Thanks for review. I've got the Rigid system and been looking for ones with drawers . The ability to work out of drawers while stacked , makes them great in a customer's home , or apartment so your not bending over , with boxes all over the floor. Rigid finally came out with drawers but it waaay to heavy !! They needed a smaller unit for the middle of the set-up. . I can't make the jump to these , the Rigid like you said, the design and durability , and ease of stacking and unstacking is excellent. I think they still need an easily stackable system, thats easier to go up and down stairs . Honestly, if Rigid just comes out with a smaller drawer unit , I'm sticking with that.
@scottschwenk95706 ай бұрын
Thanx been looking at this system going to replace what i have you may have sold me lol😊
@tomasjohansson73556 ай бұрын
I like your intro, reminds me a bit of myself, have you sought help or have you just accepted that you have this interest? Own a 550 XPG original. Thanks for a nice presentation about the differences. Greetings from Sweden
@Martin-ib5bj6 ай бұрын
Gun shots himself
@resdawgs6 ай бұрын
Me personally working on the leading edge of the building would not trust the screwing into a piece of plastic
@kwitmeh36 ай бұрын
glass filled nylon is pretty strong, if you're putting over 200lbs on this setup you have bigger issues. if you want metal threads it looks like they make all metal spider versions
@gknight77776 ай бұрын
That for the video. I like how you make us feel like we are hanging out with you. It's just like getting help from a friend.😊
@woodyj49466 ай бұрын
Longest unboxing I’ve ever seen! A Box cutter next on the list! 😂
@alanacorrea92676 ай бұрын
How can you get the spray head off, if it's stuck? Or clean the spray spouts without taking it off? Our work machine doesn't budge.
@someguy97785 ай бұрын
Did try a rag? You have to take it off to clean.
@n3qdz5 ай бұрын
If you still have a stuck head use a pair is channel lock pliers lightly as not to mark up the spray head. If you do no worrier the spray heads are very cheap, sorry so long in getting back to you
@alanacorrea92675 ай бұрын
@@n3qdz No worries, thank you for the answer!
@markheidecker92506 ай бұрын
This process was fairly easy when I did it with RT29 radios I purchased last year but I don't have access to the workstation I downloaded the software to before and when I tried it on several workstations to program the 10 additional radios we recently purchased I can't get it to work. I purchased them for a couple of Hilton brand hotels and had Hilton tech support try to do it and it didn't work for them either. Quite frustrating to have brand new radios and not be able to use them.
@n3qdz5 ай бұрын
So what is a critical part is getting the correct programming cable. The wrong cable and they are just boat anchors. Im sorry you are have such difficulty
@juanesteban88276 ай бұрын
I too am addicted to power saws, but i live in the woods and use a wood stove as my primary means of heat. However, I'm worried about a good friend who lives in the city. He comes over once or twice a month to help me cut wood. Often times he shows up unannounced and just says "Hey need help cutting firewood"! What am i going to do ?
@tomasjohansson73556 ай бұрын
Your friend needs help getting back to nature. He seeks his roots for his manhood. Give him a saw and a little pat on the back, then you have someone to cover you for all time to come. Does he drive Husqvarna even better, from Sweden with love. 🙂
@kennybrown17557 ай бұрын
Nice vid. I just bought the 2.0 set a couple weeks ago, bought the 3 pieces $140. Compared to Dewalt at $200. and Milwaukee at over $300. I’m very impressed with the quality of boxes. Again thanks for the comparison.
@chrisb94787 ай бұрын
I couldn’t find a new Stihl 261cm a couple years ago, but I found an online dealer in AL that had a Husky 550xpmk2 at a great price. I love my 550, it cuts like a sports car and from 1 detailed power test on here of all 50cc saws, the 550 has the most hp & torque. (Tied 261 for hp). Great saw! 👍🏻
@user-sk5kh8us8r7 ай бұрын
Thank you!! I was about to take it over to the hardware store to see if they could load it!
@_CzarnyZiutek_7 ай бұрын
Hi, you also covered oil tank vent. BR
@n3qdz7 ай бұрын
It oils perfectly
@user-yk2us2yp4r7 ай бұрын
I have the same machine Bunn cwft15 and it stopped heating I watched one of your videos and you mentioned to change a thermofuse wire which I did and it worked for a little while and then it stopped heating again is there something else that I should check?
@n3qdz7 ай бұрын
Well if the switch on the back it not off (i super hope it is in the off position) the problem can be 2 things. One check to see if the boiler heating element is in tact. Just taking multimeter to the boiler heating element. You should get continuity. If that isn’t tacked, it’s very possible that the thermostat board is defective. The testing procedure on that I don’t know how to handle you might be able to find a thermostat board on Bunns website to replace it with. I hope this helps.
@Fred_the_Head7 ай бұрын
I have Wera, Vessel, and PB Swiss bits.
@robertkovacic46237 ай бұрын
I agree 100% But you forgot someone - the German manufacturer of bits, screwdrivers and pliers Witte These are the best German manufacturers of bits and screwdrivers - Wiha, Felo and Witte. Although Wera is German, almost everything is produced in the Czech Republic.
Пікірлер
How is it holding up? Good review.
Thank you for the video. Our brew switch stopped working, I'm going to use this video to troubleshoot this. This is a godsend! Thank you for posting
I know this is an old post and you haven't made any videos in a while, making it on YT is not an easy gig. You give good information....BUT you repeat too much. This 24 minute video could have been a third, about 8 minutes and had the same relevant information. If ever you do more in the future, edit the repetitiveness. Also, not just you, but others that do a lot of the 1 handed stuff in front of the camera, is frustrating to watch. Otherwise, you have subscribers, views and many videos, so you have done more than a multitude of people that try to make it on YT. I don't know the exact numbers but for every successful YTuber, many have failed. Good luck if you continue on.
Do you work with Silva Brothers?
Have you got any of the Ridgid drawers yet?
Thank you!! I actually just needed to know how to safely remove that top pan to access the switches.
This review is meh
Just picked this up from Home Depot (floor display) for $19. The clearance sticker said $95 down from $189. But it has been sitting on clearance since 10/23 and it’s now 07/24 I guess it’s been going down for the past 10 months. The store just didn’t keep up with the price tag, but thankfully they sold me the floor display because they were no more in stock at that store. Got home put a battery in it and thought maybe it was a dud! But then I realize you had to press the safety bar with the trigger at the same time. Worked extremely well, better than the Friskers manual has tremors work. Plus for $19 even if they didn’t work well I couldn’t complain.
Your dog is also heavy at work. He understood the mission.
Just got a set of wcs 3 points for my ms261cm. Couldn't be happier. Glad to see you enjoying yours. How have they held up?
Just put a shim/spacer in there. These things shouldn't have these problems. For the money this sht shouldn't be happening.
K!
Hi, I’m having difficulty testing whether the led is bad, or if the input is bad from thermostat. What voltage should I be getting at the wiring harness the led plugs into. I have a 120/240 model cwtf35
thanks for the vid, helped me decide to go get the set of this, i'm so happy I found your video. was looking for a system to organize my tools and your review is very detailed with the improvements and comparison to other brands. also this could make some nice hard boxes to protect expensive radio equipment in transportation, just add some foam or cushion material. 73 from KD2OVM
They look ridiculous! And whats the point of the little mini spike bolted onto the absurdly big one? What purpose does it serve? Shame I cant get the stock 572 outer felling dawg and this is what I get in a search looking for some.
LoL, I like when you said unplug the machine, I was a appliance tech for years, And I was getting shock all the time, : )
What do you do or did do for a living?
Some bits here and some bits there 🤣
The classic B&D “dog dick in the dirt”
Nice comparison! I have an original 550xpg and love the heated handles in winter. 2017 build and I have not had any issues. But I run minimum 40:1 ethanol free 91 octane. My only dislike is the outboard clutch, do not forget to disengage the chain brake before removing the clutch cover! PITA when in the woods. Yes, an addict. My only husky and one of 7 that I own.
Great review! Thanks
Nice nail gun
I definitely want to get the new base box and drawer box but i use the original box as a seat and i wonder if the 2.0 will hold me or not.
Hi, am rebuilding one of these and I believe it’s leaking from the tank seal, so I have that on order, when taking it apart I took a pic of wires but it looks like the blanket Warmer had only one wire connected. Where does the other one go?
I’m just here for the coffee and donuts. Black with a teaspoon of sawdust pls.
I have this same exact model that I am currently trying to fix. Ive gone through hours of troublshoot. Got this for $50 at thrift store so dont know its history. To this point i replaced one brass water line that had a hole in it. And ive replaced the bug nut on top of the flow control on the back because the previous nut was cracked open (almost looked as though someone may have dropped it). After replacing these obvious things then i proceeded to troubleshoot the operation of the machine. Putting water into the top I wanted to make sure the tank was full so it could heat. Well during this process i put too much water in and water started pouring down to the bottom. I thought from previous forums i found that if i overflowed it then remainder would just come out theough the spray head. Well i was wrong which i later found out the silicone seal to the tank wasnt sealed properly. Currently it almost appears as though the top of the tank where it is bolted to the top looks warped a little bit. Not sure if it is supoosed to be flat or if its just warped. Hopefully not because i dont want to accidentally overfill it in the future and have it leak again. Ill address the leak if i can get the machine working. I have now gone through a series of testing continuity at alot of points to find my issue. I currently cant get the brewing process to start. The heating element comes on and heats the water to close to 200 degrees (i checked with a thermometer) but the water never boils up through yhe tube into the spray head through the filter tray. Was hoping maybe you had some advice for the leak spot and if you think that top could have been warped and if you know why i cant get brewing to start. Thank you
So I disconnected the spray head tube to see if there was buildup and seems to be water going through okay. Maybe my syphon gasket wasn't connected properly not allowing vapor.pressure from boiling to allow pass through to the brew cup
Update so my tank cover was warped and welded screws on tank were bent outwards preventing the cover from coming off. So I had to put the nuts on and bang the screws back so I could take the lid off. When I did I also discovered a big hole in the coil. So far this thing had 1 hole in a brass line that goes to the solenoid and coil , the flow regulator had a big hole in it and now the coil has a big hole in it and the cover was extremely warped. I'm sensing this thing had a major failure. I'm tempted to now replace the coil, new gaskets and new cover and see what it does but I'm also nervous it will fail again. Maybe that first hole created bad pressure and just created a chain reaction eventually in other points ?
Do after ally parts came in and putting everything back together, the water heater heats the water and it clicks off automatically but once it's heated and I hit the start button it still wont brew. Any idea what could still be the problem?
Have you checked out the West Coast saws felling dogs? Next level stuff!
Thanks for making this video, very helpful! On the Neiko security bit set, how did those work out for you? Thanks
You can get to bar adjuster on the 562xp ?
I just emailed to get a price
Mierda!!! Yo también tengo el mismo problema 👀soy adicto y fanático de las sierras motorizada 2t😂
How is the water level in the boiler determined? I have one that fills and keeps running and overflowing. There must be a sensor to trigger the fill valve?
Mine has the same issue that I’m currently dealing with. 1st problem to look at it is the water solenoid. Sometimes it may not seal after you brew or just sitting there. If you have a instant hot water dispenser, you can have a leak in the circuit that is still feeding the boiler volume. When you do a boiler feed for the first time you have to do it when the machine is off. Then fill up the boiler till water comes out. Then turn on the machine and press brew you should be go to go
hey. 3 days ago i buy 550xp. now i have question. i this normal? here i uploaded video on youtube. kzread.infoJ4-r6W1gxOw?si=ZwhiueXadB3P4Swj
Thanks for review. I've got the Rigid system and been looking for ones with drawers . The ability to work out of drawers while stacked , makes them great in a customer's home , or apartment so your not bending over , with boxes all over the floor. Rigid finally came out with drawers but it waaay to heavy !! They needed a smaller unit for the middle of the set-up. . I can't make the jump to these , the Rigid like you said, the design and durability , and ease of stacking and unstacking is excellent. I think they still need an easily stackable system, thats easier to go up and down stairs . Honestly, if Rigid just comes out with a smaller drawer unit , I'm sticking with that.
Thanx been looking at this system going to replace what i have you may have sold me lol😊
I like your intro, reminds me a bit of myself, have you sought help or have you just accepted that you have this interest? Own a 550 XPG original. Thanks for a nice presentation about the differences. Greetings from Sweden
Gun shots himself
Me personally working on the leading edge of the building would not trust the screwing into a piece of plastic
glass filled nylon is pretty strong, if you're putting over 200lbs on this setup you have bigger issues. if you want metal threads it looks like they make all metal spider versions
That for the video. I like how you make us feel like we are hanging out with you. It's just like getting help from a friend.😊
Longest unboxing I’ve ever seen! A Box cutter next on the list! 😂
How can you get the spray head off, if it's stuck? Or clean the spray spouts without taking it off? Our work machine doesn't budge.
Did try a rag? You have to take it off to clean.
If you still have a stuck head use a pair is channel lock pliers lightly as not to mark up the spray head. If you do no worrier the spray heads are very cheap, sorry so long in getting back to you
@@n3qdz No worries, thank you for the answer!
This process was fairly easy when I did it with RT29 radios I purchased last year but I don't have access to the workstation I downloaded the software to before and when I tried it on several workstations to program the 10 additional radios we recently purchased I can't get it to work. I purchased them for a couple of Hilton brand hotels and had Hilton tech support try to do it and it didn't work for them either. Quite frustrating to have brand new radios and not be able to use them.
So what is a critical part is getting the correct programming cable. The wrong cable and they are just boat anchors. Im sorry you are have such difficulty
I too am addicted to power saws, but i live in the woods and use a wood stove as my primary means of heat. However, I'm worried about a good friend who lives in the city. He comes over once or twice a month to help me cut wood. Often times he shows up unannounced and just says "Hey need help cutting firewood"! What am i going to do ?
Your friend needs help getting back to nature. He seeks his roots for his manhood. Give him a saw and a little pat on the back, then you have someone to cover you for all time to come. Does he drive Husqvarna even better, from Sweden with love. 🙂
Nice vid. I just bought the 2.0 set a couple weeks ago, bought the 3 pieces $140. Compared to Dewalt at $200. and Milwaukee at over $300. I’m very impressed with the quality of boxes. Again thanks for the comparison.
I couldn’t find a new Stihl 261cm a couple years ago, but I found an online dealer in AL that had a Husky 550xpmk2 at a great price. I love my 550, it cuts like a sports car and from 1 detailed power test on here of all 50cc saws, the 550 has the most hp & torque. (Tied 261 for hp). Great saw! 👍🏻
Thank you!! I was about to take it over to the hardware store to see if they could load it!
Hi, you also covered oil tank vent. BR
It oils perfectly
I have the same machine Bunn cwft15 and it stopped heating I watched one of your videos and you mentioned to change a thermofuse wire which I did and it worked for a little while and then it stopped heating again is there something else that I should check?
Well if the switch on the back it not off (i super hope it is in the off position) the problem can be 2 things. One check to see if the boiler heating element is in tact. Just taking multimeter to the boiler heating element. You should get continuity. If that isn’t tacked, it’s very possible that the thermostat board is defective. The testing procedure on that I don’t know how to handle you might be able to find a thermostat board on Bunns website to replace it with. I hope this helps.
I have Wera, Vessel, and PB Swiss bits.
I agree 100% But you forgot someone - the German manufacturer of bits, screwdrivers and pliers Witte These are the best German manufacturers of bits and screwdrivers - Wiha, Felo and Witte. Although Wera is German, almost everything is produced in the Czech Republic.