Awesome video, very detailed. Thank God for reviewers like you that cover everything, the Good, the Bad, and the Ugly. I watched your video because I was considering getting a Tank 200, but now I'm not so sure. I've watched other videos for 149cc Chinese scooters that people have clocked in at 55 mph (GPS) as their top speed, stock bike, no mods. And the carb. scooter cost them $1200 to their door including shipping. Those scooters also come with a rear top box, but, a smaller one, but no side boxes. I guess everybody has to weigh the pros and cons for themselves. We're all different, and that what makes the world go 'round. The main thing is for us to get out there, ride, and have fun. Thanks again for the video. A definite thumbs up!
@MrHugemothКүн бұрын
It should be able to go over 50 mph. Maybe wind resistance with the big panniers? I have the Clash 200 efi with the same engine, it'll easily do 55 mph (GPS checked) and will usually do 60 mph. I'm 6'1" 215 lbs and ride at 4000' and above. Nearly 5000 miles on mine so far. I would check the air filter to see if its contaminated with oil, causing a restriction. My Clash gets 76 mpg at 55 mpg with no windshield and 84 mpg with a windshield.
@MrGMATech4 күн бұрын
Sounds like a mistake
@williamhensley57267 күн бұрын
the hook up front looks more like it was made to hold shopping bags
@oldrust6017 күн бұрын
You might have to check the belt because I seen a man on that scooter that went over 60 and he weighed 200 lb ... Or you might have to adjust your clutch and if so you should be able to take it to the dealer and they check it out
@tdgdbs18 күн бұрын
My well used Honda Elite 110 can do 50mph all day long. My Zuma 50cc two stroke will do 45mph.
@theyhateme87637 күн бұрын
its illega FOR 50 CC TO DO THAT FAST, AND 110 CC HITS ANYSLOP.. IT SLOWS FAST
@andreperry79958 күн бұрын
Is that a vitacci man? I like the Bluetooth mode and i like to listening to music. Depends on the weight of the rider man. I got 63 on this scooter. This isn't a off road scooter.
@rustysuperbeetle306414 күн бұрын
Hello Chris, I am trying to find an economical response to having an oscilloscope and these capabilities as well; however, it is difficult to tell which options have the oscilloscope and which don't amongst the models. Also, I saw there's an oscilloscope MD 408, but it seems that none are in stock, so is it an older item?
@Americanboy515015 күн бұрын
Did you ever finish this system with sun and rear speakers?
@brianswelding17 күн бұрын
Man this scenario is always my worst nightmare.
@ASEWorldClassTech20 күн бұрын
Should of just been an option to delete and ignore the updates.
@chevypowertogo-907024 күн бұрын
Hey FLASH CA$H PERFORMANCE🙂, .. HEY WHATS The WATT Rating Marked on This Unit? THANK Youuuu
@adairjanney710925 күн бұрын
smoke machines are expensive though
@SamehKhan26 күн бұрын
I have a 1997 Bounder with the exact same system, minus your jacks in the centre of vehicle! My jacks still extend and retract fully, but the PowerGear system recently stopped detecting that the jack was fully retracted (I checked that it was fully up). So the system is beeping constantly when I drive, because it thinks I'm driving with jacks down. Any idea how those detection systems work, and how to solve? Thanks!
@AvocaSingleTrack28 күн бұрын
Would have helped if you showed removing the old skid plates. I'm trying to figure out where all the bolts are before just start unbolting things.
@bobbyjj537229 күн бұрын
I think if you're doing this is a good idea to wear a mask, that smoke is probably very toxic.
@rmasco71Ай бұрын
TPMS systems = gaslighting
@chrishughes6161Ай бұрын
What size was your winch?
@FlashPerformance1Ай бұрын
4k UTV wench
@dominikspencer3981Ай бұрын
Great method with the tire!! I have to pull chain link fence posts in concrete, so may be tougher...
@deandrepowensАй бұрын
So I need 14 of them at 14 feet long regular treated lumber is around 200 this would be over $1000 for this product that’s a huge jump for rubber imbedded wood
@MohammedAli-mz2vlАй бұрын
Hello sir do I need to move the SD card before reset? Thank u
@marrokenАй бұрын
Eastwood makes a $50 shelf that you add to the top of the welder that has additional mounts for the foot pedal and hoses/cables and will also have your plasma cutter on top of it. It makes the entire top surface area of the Welder a platform to house additional equipment or tools.
@Eti_ufanWilliamsАй бұрын
❤
@danwilliamson39772 ай бұрын
How did you manually get yours retracted? I have a broken wire snapped at the “leg valve assembly” right above where you talked about the dump valve and I have a jack stuck downward I can’t get retracted until I get a replacement part
@erikguth48302 ай бұрын
Try a wire splice or an alligator clip with good wire.
@danwilliamson39772 ай бұрын
I tried a wire to jump from the positive connection to where it broke off but I couldn’t get enough of a connection to trigger it at all. Found the owners manual from the prior owner and the company printed on the manual has since closed. Trying to look up the part number and haven’t had any hits yet on all the major selling sites.
@FlashPerformanceАй бұрын
I had to break the line loose and drain off the pressure.
@danwilliamson3977Ай бұрын
Awesome, that worked to get it to retract. Thanks!
@erikguth4830Ай бұрын
@@danwilliamson3977 for something mass produced you’d think the parts would be easily available. It’s not the space shuttle! I’m speaking through experience
@kings17court2 ай бұрын
I recently bought one, and they were offering a free 10AH battery with the IcyBreeze. I wanted one, and was ready to pay the $100 for the battery. When I realized I could get the battery for free, I went ahead and made the purchase. I was wondering how long the offer would last before it went away, and supposedly today is the last day of the offer. If you are on the fence, like I was, take advantage of the free battery.
@mikejoyce37822 ай бұрын
I also used a remote contactor to control my air compressor at a distance. I used a mechanical wind-up timer instead of an on/off switch. That way I can't forget actually turning off the compressor.
@thomasjohnson41112 ай бұрын
I got one of these and it's not worth having, I'll sell it for 500 if someone wants to try there luck, I screwed up and traded a Miller for this damn
@kevinsproule98782 ай бұрын
Good video I have 10000 lbs certified Atlas lift in my shop I installed over weekend absolutely no complaints
@dracolaserap2 ай бұрын
Hello, And thank you for the great video. I have a question for you. do you know if is possible to set that when you want to program a car and it's downloading the programing files from the server, to download them on the external memory not on the internal memory? i am trying to program a bmw and the files are too big for the internal memory.
@johnpope89492 ай бұрын
Aren’t you worried a little about smoking off label oils like pag 46? Ok to breathe? I mean… “the pioneers take all the arrows”, ya know?
@danielkenkama57012 ай бұрын
Just came across video... so helpful. Thanks.
@naomiallnutt21242 ай бұрын
My Micro card is corrupt and need the AL 619 software please? Please could you advise where I can get hold of this please?
@richb21242 ай бұрын
I drain mine at the end of each day and it stays clean, and have never had a smell.
@joina-li3ld2 ай бұрын
Your amazing would you please fix my 2010 CTS for 3.6 I have the same problem happening now and I’m having a buzzing going on under the hood. I don’t know what’s going on.
@typeXJuggernaut2 ай бұрын
What kinda of roller does a person us and what kinda paint can go on it ?
@ttp_0072 ай бұрын
Geee, 18 PSI still way to high for a bumpy offroad ride. I typically run at 6-8 PSI on my 33s beadlocks.
@user-hu5zj4lu4l2 ай бұрын
Thanks for your video I deeply appreciate it it helps me on my Toyota Prius because I was skeptical on hybrid cars thank you
@jeffstrains40143 ай бұрын
What is the advantage of the new display?
@pranavbanerjee56013 ай бұрын
thats a cooler. usually relaiable method in india.
@bobbaxter9523 ай бұрын
Can anyone tell me how to install an sd card in my new im508s,i want all the updates to go onto the sd card!'vehicle management' isn't in my tool.
@maskedbanditos58403 ай бұрын
What’s the weight like would you pick it up by yourself easily?
@josetrevino60543 ай бұрын
I changed the BCM, and I had placed a pin code of a Nissan Altima 3.5, 2008 and it blocked everything, What went wrong, thanks, for you help.
@MarzNet2563 ай бұрын
It helps to spray a little wd40 on old dry push pins. Makes them come out easier.
@josefranco95354 ай бұрын
I can to Program BCM with Xtool 7
@C0MM0Nbeing4 ай бұрын
Can you do this on a Renault bcm?
@MRSmith7154 ай бұрын
Yeah my doesnt do anything when i click download, like literally nothing happens
@iskoos4 ай бұрын
I will have to be a bit critical here. I like the product and I believe Autel is a reputable company. However, the instructions manual included with the model TS508, and this video above has many confusing steps. First of all, if you look at the QuickStart guide provided with the kit, you will need a second QuickStart guide to tell you how to read the first one. I found the QuickStart guide to be extremely confusing. I got lost in there. Thus, I turned to KZread for more support. The video above is a bit better but still it doesn't give you clear instructions for each step. Instead, it directs you to follow the on-screen instructions. However, the on-screen instructions have flaws. One major thing is (as enrquerubio7549 mentioned below) what to do if you do not have a spare tire! I lost so much time trying to figure out how to move to the next screen. Then steps that are telling you how to connect the tool to the vehicle is super confusing. In the manual and in the video, it tells you to turn on the vehicle first then connect the Autel tool. But the on-screen instructions that we are told to follow says otherwise. Some might say "Who cares try one or the other. You will figure it out." Sure I will, but the point here is that we have a well-known reputable company that simply cannot put out clear instructions. I don't understand why it is so difficult to be clear on what you are trying to tell people. I will tell you this much, if I was the owner of this company, the people in charge of the instruction manual and this video would be looking for a job right now. The good thing is that I am not the owner. So, if someone trying to figure this out and getting confused and stuck as I did, here is what I figured out and how it did work for me: 1. When you get to the spare tire and you don't have one, hit the "N" key. But you need to do this after trying to read the spare tire sensor. So, you will initiate "Triggering" FIRST, then hit the "N" button. If you hit the "N" before initiating triggering, it will cancel the whole process and take to the beginning. 2. As for the order of connection, I connected the tool first and then powered on the vehicle (put it in accessories mode, no need to run the engine). Connecting the tool while the vehicle and tool is on is not proper in my opinion. so, the above worked well for me and the TPMS light cleared out. Thanks
@kolbyvondy39934 ай бұрын
Does the cut 60 work well with the arcdroid? I have had there are some issues with compatibility. Did you have to do anything to make them work together?
@FlashPerformance4 ай бұрын
I didn't change anything. I just wired it in per the directions and started cutting. I don't have to do anything special at all. I am very happy with it so far
@TattedTommysTv4 ай бұрын
So is this sane as basically what they say a reset cause I replaced my battery in my X5 and it keeps going into limp mode someone told me I had to register my battery would this cause it to run poorly?
@mperlatti4 ай бұрын
Do you have to reprogram already established keyfobs?
Пікірлер
Awesome video, very detailed. Thank God for reviewers like you that cover everything, the Good, the Bad, and the Ugly. I watched your video because I was considering getting a Tank 200, but now I'm not so sure. I've watched other videos for 149cc Chinese scooters that people have clocked in at 55 mph (GPS) as their top speed, stock bike, no mods. And the carb. scooter cost them $1200 to their door including shipping. Those scooters also come with a rear top box, but, a smaller one, but no side boxes. I guess everybody has to weigh the pros and cons for themselves. We're all different, and that what makes the world go 'round. The main thing is for us to get out there, ride, and have fun. Thanks again for the video. A definite thumbs up!
It should be able to go over 50 mph. Maybe wind resistance with the big panniers? I have the Clash 200 efi with the same engine, it'll easily do 55 mph (GPS checked) and will usually do 60 mph. I'm 6'1" 215 lbs and ride at 4000' and above. Nearly 5000 miles on mine so far. I would check the air filter to see if its contaminated with oil, causing a restriction. My Clash gets 76 mpg at 55 mpg with no windshield and 84 mpg with a windshield.
Sounds like a mistake
the hook up front looks more like it was made to hold shopping bags
You might have to check the belt because I seen a man on that scooter that went over 60 and he weighed 200 lb ... Or you might have to adjust your clutch and if so you should be able to take it to the dealer and they check it out
My well used Honda Elite 110 can do 50mph all day long. My Zuma 50cc two stroke will do 45mph.
its illega FOR 50 CC TO DO THAT FAST, AND 110 CC HITS ANYSLOP.. IT SLOWS FAST
Is that a vitacci man? I like the Bluetooth mode and i like to listening to music. Depends on the weight of the rider man. I got 63 on this scooter. This isn't a off road scooter.
Hello Chris, I am trying to find an economical response to having an oscilloscope and these capabilities as well; however, it is difficult to tell which options have the oscilloscope and which don't amongst the models. Also, I saw there's an oscilloscope MD 408, but it seems that none are in stock, so is it an older item?
Did you ever finish this system with sun and rear speakers?
Man this scenario is always my worst nightmare.
Should of just been an option to delete and ignore the updates.
Hey FLASH CA$H PERFORMANCE🙂, .. HEY WHATS The WATT Rating Marked on This Unit? THANK Youuuu
smoke machines are expensive though
I have a 1997 Bounder with the exact same system, minus your jacks in the centre of vehicle! My jacks still extend and retract fully, but the PowerGear system recently stopped detecting that the jack was fully retracted (I checked that it was fully up). So the system is beeping constantly when I drive, because it thinks I'm driving with jacks down. Any idea how those detection systems work, and how to solve? Thanks!
Would have helped if you showed removing the old skid plates. I'm trying to figure out where all the bolts are before just start unbolting things.
I think if you're doing this is a good idea to wear a mask, that smoke is probably very toxic.
TPMS systems = gaslighting
What size was your winch?
4k UTV wench
Great method with the tire!! I have to pull chain link fence posts in concrete, so may be tougher...
So I need 14 of them at 14 feet long regular treated lumber is around 200 this would be over $1000 for this product that’s a huge jump for rubber imbedded wood
Hello sir do I need to move the SD card before reset? Thank u
Eastwood makes a $50 shelf that you add to the top of the welder that has additional mounts for the foot pedal and hoses/cables and will also have your plasma cutter on top of it. It makes the entire top surface area of the Welder a platform to house additional equipment or tools.
❤
How did you manually get yours retracted? I have a broken wire snapped at the “leg valve assembly” right above where you talked about the dump valve and I have a jack stuck downward I can’t get retracted until I get a replacement part
Try a wire splice or an alligator clip with good wire.
I tried a wire to jump from the positive connection to where it broke off but I couldn’t get enough of a connection to trigger it at all. Found the owners manual from the prior owner and the company printed on the manual has since closed. Trying to look up the part number and haven’t had any hits yet on all the major selling sites.
I had to break the line loose and drain off the pressure.
Awesome, that worked to get it to retract. Thanks!
@@danwilliamson3977 for something mass produced you’d think the parts would be easily available. It’s not the space shuttle! I’m speaking through experience
I recently bought one, and they were offering a free 10AH battery with the IcyBreeze. I wanted one, and was ready to pay the $100 for the battery. When I realized I could get the battery for free, I went ahead and made the purchase. I was wondering how long the offer would last before it went away, and supposedly today is the last day of the offer. If you are on the fence, like I was, take advantage of the free battery.
I also used a remote contactor to control my air compressor at a distance. I used a mechanical wind-up timer instead of an on/off switch. That way I can't forget actually turning off the compressor.
I got one of these and it's not worth having, I'll sell it for 500 if someone wants to try there luck, I screwed up and traded a Miller for this damn
Good video I have 10000 lbs certified Atlas lift in my shop I installed over weekend absolutely no complaints
Hello, And thank you for the great video. I have a question for you. do you know if is possible to set that when you want to program a car and it's downloading the programing files from the server, to download them on the external memory not on the internal memory? i am trying to program a bmw and the files are too big for the internal memory.
Aren’t you worried a little about smoking off label oils like pag 46? Ok to breathe? I mean… “the pioneers take all the arrows”, ya know?
Just came across video... so helpful. Thanks.
My Micro card is corrupt and need the AL 619 software please? Please could you advise where I can get hold of this please?
I drain mine at the end of each day and it stays clean, and have never had a smell.
Your amazing would you please fix my 2010 CTS for 3.6 I have the same problem happening now and I’m having a buzzing going on under the hood. I don’t know what’s going on.
What kinda of roller does a person us and what kinda paint can go on it ?
Geee, 18 PSI still way to high for a bumpy offroad ride. I typically run at 6-8 PSI on my 33s beadlocks.
Thanks for your video I deeply appreciate it it helps me on my Toyota Prius because I was skeptical on hybrid cars thank you
What is the advantage of the new display?
thats a cooler. usually relaiable method in india.
Can anyone tell me how to install an sd card in my new im508s,i want all the updates to go onto the sd card!'vehicle management' isn't in my tool.
What’s the weight like would you pick it up by yourself easily?
I changed the BCM, and I had placed a pin code of a Nissan Altima 3.5, 2008 and it blocked everything, What went wrong, thanks, for you help.
It helps to spray a little wd40 on old dry push pins. Makes them come out easier.
I can to Program BCM with Xtool 7
Can you do this on a Renault bcm?
Yeah my doesnt do anything when i click download, like literally nothing happens
I will have to be a bit critical here. I like the product and I believe Autel is a reputable company. However, the instructions manual included with the model TS508, and this video above has many confusing steps. First of all, if you look at the QuickStart guide provided with the kit, you will need a second QuickStart guide to tell you how to read the first one. I found the QuickStart guide to be extremely confusing. I got lost in there. Thus, I turned to KZread for more support. The video above is a bit better but still it doesn't give you clear instructions for each step. Instead, it directs you to follow the on-screen instructions. However, the on-screen instructions have flaws. One major thing is (as enrquerubio7549 mentioned below) what to do if you do not have a spare tire! I lost so much time trying to figure out how to move to the next screen. Then steps that are telling you how to connect the tool to the vehicle is super confusing. In the manual and in the video, it tells you to turn on the vehicle first then connect the Autel tool. But the on-screen instructions that we are told to follow says otherwise. Some might say "Who cares try one or the other. You will figure it out." Sure I will, but the point here is that we have a well-known reputable company that simply cannot put out clear instructions. I don't understand why it is so difficult to be clear on what you are trying to tell people. I will tell you this much, if I was the owner of this company, the people in charge of the instruction manual and this video would be looking for a job right now. The good thing is that I am not the owner. So, if someone trying to figure this out and getting confused and stuck as I did, here is what I figured out and how it did work for me: 1. When you get to the spare tire and you don't have one, hit the "N" key. But you need to do this after trying to read the spare tire sensor. So, you will initiate "Triggering" FIRST, then hit the "N" button. If you hit the "N" before initiating triggering, it will cancel the whole process and take to the beginning. 2. As for the order of connection, I connected the tool first and then powered on the vehicle (put it in accessories mode, no need to run the engine). Connecting the tool while the vehicle and tool is on is not proper in my opinion. so, the above worked well for me and the TPMS light cleared out. Thanks
Does the cut 60 work well with the arcdroid? I have had there are some issues with compatibility. Did you have to do anything to make them work together?
I didn't change anything. I just wired it in per the directions and started cutting. I don't have to do anything special at all. I am very happy with it so far
So is this sane as basically what they say a reset cause I replaced my battery in my X5 and it keeps going into limp mode someone told me I had to register my battery would this cause it to run poorly?
Do you have to reprogram already established keyfobs?