Пікірлер

• 
  @FrogUniverse4 күн бұрын

  Yee haw buddy

• 
  @r1sabotage5 күн бұрын

  Im having the same issue. what I'm up to is i checked the rotary valve clearance and its way out of spec. It's supposed to be .300mm and .350mm being the max. Im at .582mm and the rotary valve gear has some minor play. Fingers crossed addressing those two will fix my ski. Before learning about the rotary valve i was so confused. I had spark, fuel, compression and air and no boom. Before this problem, my check valve was bad and she refused to start. Just too many little things will make this ski not have combustion.

• 
  @murderyurface35955 күн бұрын

  You wanna know what works even better than a zip tie? A large hose clamp!

• 
  @allcore51725 күн бұрын

  Lucky it didn’t crank up spraying all that starter fluid into it

• 
  @KaydenHale-n8r9 күн бұрын

  Click bait ass dude. Zip tie trick. Buy exhaust cutter. Fucking weirdo

• 
  @BustedRadialGarage13 күн бұрын

  Good to see you back brother!

• 
  @coreystevens60117 күн бұрын

  This is a simpler engine more like a chainsaw that a motorcycle or car. Valve timing stoke issues there as there are only 2 stokes per cycle. I think you are doing good except for maybe joining a sea-doo forum and downloading and printing out a proper service / repair manual. You probably should have at least done some research on 2 stoke engines , that may not have been as entertaining as it has been . I enjoyed watching you struggle. I purchased a not running 98 Xp with sugar in the gas tank that had not been run through the system only because the key was missing. It is now my favorite thing but I struggled too. the non genuine carb kit may be an issue you should at least be able to test the carb functionality with a small pump tester with an air pressure guage. I found one for $26 on Amazon. Good luck to you. I hope you get it running.

• 
  @kentaylor742817 күн бұрын

  a long shot 3 year old video but here it is I want to do a 3-2 on my 91 what size tires and rims you running with them 2in drop spindles I can't seem to get answer on line. can I run my stock 14's

• 
  @PatinaPitstop17 күн бұрын

  You should be able to run the 14's. You are limited with tires sizes though. I would run a 235/60r14 front and back.

• 
  @booshayware600321 күн бұрын

  I’m having the same issue with a friends jet ski’s I was just in your situation to say something can be done but I still can’t get it to kick all the way over

• 
  @RIPPL_RIDERZ23 күн бұрын

  Lol it was killing me that he didn’t just pour some gas in the carbs 😂

• 
  @PatinaPitstop21 күн бұрын

  I hit it was starting fluid 😁

• 
  @RIPPL_RIDERZ13 күн бұрын

  @@PatinaPitstop starter fluid and pouring 2 stroke fuel into the intake/cylinders are two different things

• 
  @christoto7y28 күн бұрын

  Love this tool but they should at put a tension screw like the like ones for copper pipe good tricks gonna use it

• 
  @garrettgough6658Ай бұрын

  4 mins in, and im willing to bet Battery is an issue, if not the main issue. everyone in the seadoo comunity knows those batteries are terrible & dont have enough jucie to turn the motor. they just dont last

• 
  @14shawn44Ай бұрын

  That was somewhat painful yet entertaining to watch lol. That’s a rotax rotary valve engine. There’s a valve plate that replaces traditional reeds in a 2 stroke engine. So long as nobody has been in there moving things, the rotary valve was probably ok. One HUGE mistake you were already warned about is the carb rebuild kit. I didn’t have to see it to know there was fuel just spraying out of the plug holes. That’s the cheap rebuild kit.. very bad material that opened the pop off valve way too early. They weren’t kidding about genuine mikuni ONLY. You had a great start though! I’m concerned with how hard it was to turn over even with a new starter, but you had compression, spark, and thankfully the dess key worked. That’s usually a big problem. I would have checked the rotary valve timing just to be sure and gone genuine mikuni rebuild. You were right there. If it started and ran off I’d do a leak down test checking the outer seals. At least you got your hands in it and gave it a shot. I like rescuing old skis!

• 
  @PatinaPitstopАй бұрын

  Thank you so much for the comment. It was fun to mess with but I'll definitely stick with old cars.

• 
  @pucho513Ай бұрын

  I have made it to 28:17 and I'm rooting for you to get this sucker started, LETS GOOOO 🤞🏾

• 
  @yoyofdАй бұрын

  you could have low compression or the impeller stuck . if you sprayed the carbs and didn’t start forget the carbs , there is something else . i’ll say compression

• 
  @KungpaoshizziАй бұрын

  Tonight at 6, little girl gets shrapnel from compromised structural integrity

• 
  @excitationofstereocilia2103Ай бұрын

  I’m doing this on my engine

• 
  @johnscreekmarkАй бұрын

  I installed one very similar to that on my 88. That lead on the firewall did have a stock connector, but I ended up parallel-spicing the tach signal-wire into it. I confirmed it with a Volt meter…gave me a pulsating 12v signal.

• 
  @nomadgaming3170Ай бұрын

  Did you check the fuel and the compression?

• 
  @dano4572Ай бұрын

  Wheel sizes!! Offsets!!??

• 
  @PatinaPitstopАй бұрын

  Stock factory rallies. 15x8 in back 4 inch backspace I think. 255/60r15 tires. Fronts are 15x7 with 4 1/4 backspace i believe. 215/70r15 tires but i think 215/65 would look better

• 
  @dano4572Ай бұрын

  @@PatinaPitstop thank you, sir!!

• 
  @nickmorales21972 ай бұрын

  I’ve had the exact same problem with a bombardier engine. They have rotary values. I was pumped watching this as I’ve been trying to get mine started. I’ve done everything you did. Ended up being the cables from the starter to the solenoid. Had built up corrosion over the years and not allowing enough amps. Awesome video, you are not an idiot. Bump those other guys. Boats and jet skis take a different set of knowledge. Keep up the good work. 🤙🏽

• 
  @davelee31522 ай бұрын

  Doin this today

• 
  @techwiz24102 ай бұрын

  Cool video to watch.. until I realized I lost 45min of my life to a old just slow ski.. and a seadoo at that. I'll still give you a like on this video for your efforts because I work on all my own stuff too but wouldn't give 5 min to a ski that old.

• 
  @martinrascon13502 ай бұрын

  BLACK RTV SEALANT WILL WORK BETTER

• 
  @setharithsuon31002 ай бұрын

  👍

• 
  @ElplebeTex2 ай бұрын

  Where’s the finished product?

• 
  @PatinaPitstop2 ай бұрын

  I ended up selling it to make more room in my garage 😔

• 
  @jaden563229 күн бұрын

  @@PatinaPitstop how much did you get for it?

• 
  @PatinaPitstop21 күн бұрын

  $300 i think 🤔

• 
  @jonandash4life982 ай бұрын

  Bout to try this to put my stock mufflers back on

• 
  @tropicaloasis82032 ай бұрын

  Currently working on one myself! Been sitting up for years was my dads i rode it when i was lime 5 or 6, im 26 now may as well get it to use!

• 
  @lambert4392 ай бұрын

  Gonna do this to the oil pan in my 7.3 sure beats pulling the engine for a new pan

• 
  @jackietaylor51653 ай бұрын

  Thanks gonna try this on an old mustang oil pan leak🎉

• 
  @kameroncarter67153 ай бұрын

  Hurting this video hurts my eyes lmao I don’t get how you can build your car and be so into a car and have no common sense with motors…

• 
  @boostedsixthgen2 ай бұрын

  He quits after every fail 😂

• 
  @PatinaPitstop2 ай бұрын

  An engine needs air, fuel, spark and compression. I had those things. I really felt it was a valve adjustment/timing problem. Thanks for commenting, yes i know I'm an idiot 😁

• 
  @PatinaPitstop2 ай бұрын

  The more i try, the more I realize how much I sux. 🤣

• 
  @rubenorozcoa96433 ай бұрын

  bro you need to connec water hose in the inlet by the water turbine out back

• 
  @dtruth57693 ай бұрын

  It says flex seal isnt good for oil leaks

• 
  @thomaskovacs50943 ай бұрын

  Couldn't tell because of the time lapse, about how much time did that cut take?

• 
  @hommysosa40283 ай бұрын

  Very very useful men.👍💪💪

• 
  @ExtremeRecluse4 ай бұрын

  What about the breather valve on top. The pressure will build and start leaking if it is broken

• 
  @geraldscott43024 ай бұрын

  I have a '93 S-10, 2 door, 2 wheel drive, short bed. It came with a 2.8L EFI V6 and a 5 speed. It now has a carbureted 383ci V8 and a Muncie "rock crusher" 4 speed, as well as a Ford 8.8 rear axle. I didn't lower it. I wanted it to be drivable. I put 225/70-14 BFG Radial T/As on 14x6 Camaro Rallys in the front, and huge 275/60-15 Radial T/As on mid '70s 15x8 Corvette Rallys in the rear. Quite a few other things too, but that is the big stuff. I tried my best to make it look like an early '70s muscle car, and I think it turned out well. It has a true dual exhaust out the back, with glasspacks, and just over 400hp at the rear wheels at 5400 rpm. Burnouts are super easy. It's almost hard not to do one. You have to take it easy on the pedal. I bought all new aftermarket reproduction rally wheels, trim rings, and center caps. The 14x6 Camaro and 15x8 Corvette rallys are exactly the same other than size. All in all I have over $2000 into tires and wheels. Did you check the pinion angle? It needs RWL tires, trim rings, and a cowl hood.

• 
  @jibbymcbeet4 ай бұрын

  Hey man, I got this SeaDoo I was hoping you could take a look at haha jk. Cool video. Good luck with your channel

• 
  @robertmethia70804 ай бұрын

  thats what she said

• 
  @Yhyujss5 ай бұрын

  I think I'll use a angle grinder it will save me 20min of labour

• 
  @ExtremeRecluse5 ай бұрын

  How much would it cost to have the entire underside sand or soda blasted?

• 
  @Luminous.Dynamics5 ай бұрын

  They should sell some that lock like vise grip locking pliers

• 
  @jrjunior93275 ай бұрын

  This will only make things worse over time it will create more moisture under the flex seal then there was before. Better option for quick fix would not recommend this fix.

• 
  @PatinaPitstop5 ай бұрын

  It was definitely intended as a temporary fix. I have lost track of the truck but last i heard it wasn't leaking after 1 year.

• 
  @scottymo85975 ай бұрын

  Hmm i have a leaking rear end on a chevy avalanche but the hole on the bottom. Im gonna try this.

• 
  @ahmadghosheh31045 ай бұрын

  Great trick for my arthritic hands 😂😊

• 
  @johnchadbone5 ай бұрын

  Good bit of thinking outside the box. Noice👍

• 
  @Muffin1922135 ай бұрын

  Would some cutting oil spray help the blades cut through?

• 
  @PatinaPitstop5 ай бұрын

  Good idea!

• 
  @noyfub5 ай бұрын

  Thanks. I think I'll try it on my 01 Tundra. My rear axle isn't quite as bad.

• 
  @bcapgamez40056 ай бұрын

  Thanks for the zip tie trick

• 
  @brushlak81736 ай бұрын

  ahhh nothing like working on a car in the fkn freezing cold