Hammer Missions helps commercial drone professionals & UAV teams collect, process and deliver quality data for asset mapping & inspection. To learn more, visit hammermissions.com
The ground offset is important however is it true that your ground offset is only as accurate as the numbers you put in? How can a pilot get the exact height of the structure to ensure the proper ground offset? I did not get the same experience wile trying to create a project. The facade map was all other the place and the roof map didn't show the complete map. some lines were missing and the proposed flight path for both seemed eradicate. I also got a different flight path for the same building every time I tried it.
@HammerMissions4 күн бұрын
Hi there! Ground offset should can be estimated by looking at the building on Google Earth initially and then the actual value for ground offset should be changed on site by using the drone to measure the building's height! Hope this helps. For any questions related to Hammer, please do get in touch with our support team at [email protected]
@NikolaGnjatovic8 күн бұрын
Does Hammer Missions work with DJI Matrice 350 RTK?
@HammerMissions7 күн бұрын
Yes!
@NikolaGnjatovic7 күн бұрын
@@HammerMissions Super! And does it follow IEC TS 62446-3:2017 standards for aerial thermography? Im planning to use Hammer for solar panel inspections.
@Velo-Rides14 күн бұрын
This looks a fantastic piece of software, just a tad too expensive for someone starting out.
@HammerMissions13 күн бұрын
Thank you for your kind words!
@kentmeier676217 күн бұрын
What about determining azimuth for missions
@kentmeier676217 күн бұрын
Have you been able to use qgis for drone mag data K. Meier Earthex Geophysical Solutions
@JCDiaz-Skytech18 күн бұрын
Great! 👍
@HammerMissions18 күн бұрын
thank you!
@dronetoulouse19 күн бұрын
👍
@HammerMissions18 күн бұрын
thank you!
@clintonherring19 күн бұрын
Thanks for pointing me to this vodeo
@stephenaseltinejr.356420 күн бұрын
BRO THIS CONTENT IS PRIME! glad I found it before it cost money lol. Your amazing brother. Appreciate the content and the help! My new magic 3E is arriving tomorrow. Gonna be doing mapping and stockpile surveys I hope. Starting my own business is the idea. Keep it coming man.
@clintonherring21 күн бұрын
I’m just here to see how to cost an inspection, does it cover that?
@HammerMissions21 күн бұрын
check this one out for that! kzread.info/dash/bejne/n213t7R9YNHIdLw.html
@parmodjuneja428129 күн бұрын
Is this support for air 2
@droneoccitanieАй бұрын
Can´t wait.
@mehulsolanki4526Ай бұрын
Very nice video Sir, Could please share the name of Apk and Software used for Mapping for DJI Mini 3 Pro
@HammerMissionsАй бұрын
It's Hammer Missions! The APK has not been released yet but we expect by May end this year
@mehulsolanki4526Ай бұрын
@@HammerMissions Noted with thanks Sir Hope to see the same Soon.
@mehulsolanki45269 күн бұрын
@@HammerMissionsHello Sir, Any Update regarding the Apk?.
@mehulsolanki45269 күн бұрын
@@HammerMissionsHello Sir, Any Update regarding the Apk,? please reply
@HammerMissions9 күн бұрын
@@mehulsolanki4526 Hi there, we have released the APK to select partners at the moment. We aim to bring it to everyone soon!
@newaltitudephotography8394Ай бұрын
When is support for mini 3 coming and also air 2s?
@HammerMissionsАй бұрын
We expect May 2024 for the Mini 3 Pro, no ETA for the Air2S at the moment.
@mKras-wu4jkАй бұрын
I'm making building inspections professionally, traditional way, by walking, checking, making pictures, and your solution looks nice and easy, but results are, for technical evaluation, below expectations.... 1. The low resolution (because of distance of taking pictures do not allow to make accurate evaluation of degradation of particular parts especially, most important state of roof surface: cracks, possible leaks) 2. The game changer will be the possibility of making accurate measurements on this model (not on all directions, but on main surfaces of the building - along walls and roof) There are any solution of this issues? Probably when we will get better quality images the model will hang because of its size...
@HammerMissionsАй бұрын
Hi there! thanks for your comments. Solutions exist! 1. You can always take close up pictures and simply add them to the dataset. 2. You can do that already: kzread.info/dash/bejne/p6eTy5mffq7Tc6Q.html You can add thousands of images to the project without worrying about the size and all works inside your web browser
@jimpugh1553Ай бұрын
Why was there no ground offset entered?
@HammerMissionsАй бұрын
Well spotted! This mission should ideally use a ground offset, but since this was an inspection only mission and the post processing to make a map/model was not needed, getting exactly the overlap was less crucial.
@jimpugh1553Ай бұрын
When you added the images to the project, I noticed you only added the facade images from you folder. Do you then add the roof images into the same project folder?
@HammerMissionsАй бұрын
That's correct, you would add the roof and facade images in the same project if your goal is to create a 3D model including both the roof and the facade.
@egbertrichards2314Ай бұрын
*Promo sm* ✨
@ToreyThompson1Ай бұрын
I’m using gcp’s for an interior map. Do I place the DJI RTK base station on say 3 of the GCP’s I’ve placed down? And if so, should I let the RTK gather data for say 15 minutes each?
@HammerMissionsАй бұрын
Hi there! Yes, you should typically wait for the RTK / Base Station module to stabilise on each of the GCPs to note the correct positions. However, you might find that your true challenge is getting reliable GPS signal indoors!
@w.e.s.Ай бұрын
No reason to use a 3e for mapping. In fact its got lesser camera quality youd be better off with a mini
@dzhou8814Ай бұрын
what program you are using to map the roof??
@HammerMissionsАй бұрын
It's Hammer Missions! hammermissions.com
@KunalSharma-mp9mkАй бұрын
Hello Varun, we've been trying to reach you for some facade inspection support. Please do let us know when's a good time to connect.
@jimpugh15532 ай бұрын
Would have liked to have seen a but more detail on how he went about making the field adjustments to the flight plan.
@HammerMissionsАй бұрын
We'll do our next video just on that!
@truevegas2 ай бұрын
Does Hammer Missions work with the DJI Air2S?
@HammerMissionsАй бұрын
Not at the moment but it's on the roadmap!
@aguila4132 ай бұрын
What software are u using?
@HammerMissions2 ай бұрын
Hammer Missions! hammermissions.com
@relentless_18292 ай бұрын
Great video. Hope to be using Hammer Mission soon.
@seekter-kafa2 ай бұрын
quality has nothing to do with (optimal) fly speed! the thing is does battery depletes exponentially faster with speed, so there is optimal speed for gaining maximum distance, camera or no camera
@HammerMissions2 ай бұрын
Hi there, if you fly faster than your camera can take photos, you will miss photos, which can affect the overall quality of the dataset, once processed. Hope this clarifies!
@seekter-kafa2 ай бұрын
@@HammerMissionsi think i need to clarify -flying is flying and filming is filming, your video title talks about flying, not filming, not all drone flights are for content creation, duh
@bryanspelhaug21352 ай бұрын
We always have a need on our jobsite to check elevation for say spoils haul off. We are currently using Drone Deploy with Emlid survey software to collect data for GCPs. It works well but it is time consuming for setup sometimes. You mentioned smart GCP's, I'm interested in looking into that workflow. Might save time and money! Has anyone on your team used the smart GCP method?
@MarceloFerreira-zi2qz2 ай бұрын
Hii, whats this software for mapping?
@HammerMissions2 ай бұрын
It's Hammer Missions! hammermissions.com
@stabila97063 ай бұрын
Wished i could afford the product... As a new Drone company the pricing is just far too much..
@HammerMissions3 ай бұрын
Hi! sorry to hear the pricing is not aligning with your business model. Are you sure you are pricing your clients correctly? We have a few videos on that which might be helpful: 1. kzread.info/dash/bejne/n213t7R9YNHIdLw.html&ab_channel=HammerMissions 2. kzread.info/dash/bejne/gpimyZiyn6WocZs.html&ab_channel=HammerMissions
@squadsight3 ай бұрын
How to not what it is the question was! @$%^^!
@HammerMissions3 ай бұрын
Hi there! 👋 Are you looking for a workflow video on how to measure stockpiles? This video might be helpful: kzread.info/dash/bejne/mXimzsSQfazgk5c.html
@UAV-Magazine3 ай бұрын
Yes, more flexibility in post-processing!! Retaining more color information is important. We dont want compressed detail 😉
@user-xi4uu2cx7x3 ай бұрын
Hi what a great video. I am interested in this type of work and equipment, could you give any advice on some one like my self a novice breaking onto this industry. I am able to fly a drone etc but where could i do courses for all of the survey work etc . Many thanks for your time. Kevin
@HammerMissions3 ай бұрын
Thank you for you kind words! We would recommend subscribing to our channel as we regularly post educational videos on drone survey & inspection related work. If you are looking to specifically break into magnetic surveying, we recommend speaking to Geometrics (magnetometer manufacturers) and looking into the mineral exploration industry. Good luck!
@kalrutter3 ай бұрын
Great video
@HammerMissions3 ай бұрын
Thank you! 🙏
@thegoldbug3 ай бұрын
Costs 2 new P4RTKs (and spare batteries) can be purchased for the cost of one M3E or buy a P4RTK and a base station for same price. 20Mp cameras on both so I don't understand the comments that data quality is better with the M3E.
@terorvladАй бұрын
M3e has a 1 inch newer sensor as opposed to a micro 4/3 sensor on the phantom. The interval rate is faster with the mavic and it can pretty much finish the same amount of work in half the time.
@vladimir-62283 ай бұрын
In addition to the 2D map of the roof, can Hammer Missions generate a 2D ortho projections of the facades?
@HammerMissions3 ай бұрын
At the moment, you can only create a 3D model of the facades but 2D ortho is on the roadmap!
@vladimir-62283 ай бұрын
Excellent!
@PeterPiccolo3 ай бұрын
can this be done with a mavic 2 zoom?
@HammerMissions3 ай бұрын
Creating a 2D map? Yes!
@sid42763 ай бұрын
Nice explanation thanks.
@jakeduckworth23503 ай бұрын
Thanks loving your content
@HammerMissions3 ай бұрын
Thank you! 🙏
@trevorsmith29383 ай бұрын
can i use my mavic 2 pro
@HammerMissions3 ай бұрын
Yes you can! We recommend our Android app for the M2P
@lookingdowndrone3 ай бұрын
thanks, this is really useful
@jcinewilliams88193 ай бұрын
I'm new to drones and just purchased me an Autel evo 2 v3. I really like what you demonstrated and interested in using this program. Will this program be available to an Autel drone Aircraft? Also what do you mean by ground offset altitude? Great video, thanks in advance!
@HammerMissions3 ай бұрын
thanks for your kind words! We have autel on the roadmap but no release date as of yet
@mateuszwieczorekbachus56394 ай бұрын
Sorry I didn’t catch what software You using there ?
@HammerMissions4 ай бұрын
It's Hammer Missions! hammermissions.com
@uavsitesurvey4 ай бұрын
Great video but I had to turn off, the background noise/music was making it uncomfortable to concentrate
@HammerMissions4 ай бұрын
Oh no! We'll try to lower / remove the background score in the next one!
@sebastiandemuria43174 ай бұрын
(Message 1/2) Hello team, I liked your video, it accommodated my lack of understanding of some things regarding the three processing methods for geolocation of image sampling. I would like to ask you just 2 questions: 1.- IF you had to acquire equipment to make 2D/3D, orthomosaic/lever curves, points cloud, DEM models in mountains with forests, and smooth areas such as roads or old bridges to remodel ===> What equipment would you use? Was this team good? ==> M350 RTK, Zenmuse P1, Zenmuse L2 or PhaseOne IXM-100. 2.- Today the market is already equipped with many of these Mapping activities. With the equipment mentioned in point 1, it could make a difference in providing a higher quality service or it is not worth the effort to acquire this equipment because there are other processes. PPT that improves the quality of deliverables to the client. 3.- How could I match or get closer to the precision and results of the millimetric measurements of the millimetric equipment of traditional conventional surveyors? Could this PhaseOne IXM-100 40 MG pixel camera help or not? 4.- If I implement RTK, 3/4 of the time of surveying 200 hectares, my RTK GCP loses connectivity, could I continue surveying the sampling and then process everything with the PPK method? @sebastiandemuria4317 🤔
@HammerMissions4 ай бұрын
1 - There isn't a single absolute best equipment! We suggest reading our guide on how to buy the right drone: www.hammermissions.com/post/how-to-buy-drones 2 - It all starts with identifying a niche (small segment of the market) and serving that niche better than anybody else using your competitive advantages! 3 - Accuracy of the dataset has less to do with the camera and more to do with whether GCP/RTK/PPK was used. kzread.info/dash/bejne/l4Kr1Lp7pbDXiso.html 4 - Yes, one advantage of the PPK / GCP methods is that they are not real time method, so even if you lose connection, you can use to create higher accuracy outputs! Hope this helps!
@sebastiandemuria43174 ай бұрын
@@HammerMissions Thanks for your prompt answers. 🙂
@sebastiandemuria43174 ай бұрын
Message (2/2) 5.- Could you make a video with the differences between photometry and LiDAR? I understand the topic, but I would like to know more about where each one applies, I understand that LiDAR is better in forests, while photogrammetry is better on surfaces or to make orthomosaics It would be good to hear your experience on the subject. I am analyzing all this information to learn whether I could invest in a business that might offer a difference in the service outputs. Nowadays, many companies are providing this service, and I am wondering whether I can offer something better. Do you think this could be reached? Any comment would be awesome. Thanks for reading my comment. Kind regards. Sebastian
@brendanbrady34314 ай бұрын
Ok you mention using survey grade equipment for positioning GCPs, then say later that it's a low up-front cost method
@HammerMissions4 ай бұрын
It's lower upfront cost as RTK drones or PPK software are not strictly required. It's more expensive in time spent layout the GCPs! 🏁
@JonWitsellPhotographicArtsАй бұрын
@@HammerMissions What's expensive is the GNSS receiver you need to accurately locate your GCPS-or the surveyor. Later you said you just put them down, but they are useless as ground control unless you have them accurately located. They are NOT low cost upfront. GCP targets: $100. GNSS receiver: $6K for our EOS Arrow. Emlid will get you cheaper.
@HammerMissionsАй бұрын
@@JonWitsellPhotographicArts Our point was that all things being equal, they are lower cost than RTK or PPK methods as they do not require you to purchase an RTK drone, which at the time were typically higher priced than non-RTK drones. The cost for RTK drones has fallen sharply since and almost all new enterprise drones now have RTK enabled (yay!). And yes, we do recognise that the GNSS receiver can also be cost prohibitive! 👍
4 ай бұрын
Could you perform calibration with the screen of the controller?
@HammerMissions4 ай бұрын
Not the vision one! You'll need the calibration board for that one 👍
@user-pu5xl4mh4j4 ай бұрын
Thank you for the great video, how many photos did you end up stitching for your model?
@HammerMissions4 ай бұрын
Thank you for the kind words! It was around 376 photos: kzread.info/dash/bejne/gH5okrOYitzfgMo.htmlfeature=shared&t=1080
Пікірлер
Great video thankyou
The ground offset is important however is it true that your ground offset is only as accurate as the numbers you put in? How can a pilot get the exact height of the structure to ensure the proper ground offset? I did not get the same experience wile trying to create a project. The facade map was all other the place and the roof map didn't show the complete map. some lines were missing and the proposed flight path for both seemed eradicate. I also got a different flight path for the same building every time I tried it.
Hi there! Ground offset should can be estimated by looking at the building on Google Earth initially and then the actual value for ground offset should be changed on site by using the drone to measure the building's height! Hope this helps. For any questions related to Hammer, please do get in touch with our support team at [email protected]
Does Hammer Missions work with DJI Matrice 350 RTK?
Yes!
@@HammerMissions Super! And does it follow IEC TS 62446-3:2017 standards for aerial thermography? Im planning to use Hammer for solar panel inspections.
This looks a fantastic piece of software, just a tad too expensive for someone starting out.
Thank you for your kind words!
What about determining azimuth for missions
Have you been able to use qgis for drone mag data K. Meier Earthex Geophysical Solutions
Great! 👍
thank you!
👍
thank you!
Thanks for pointing me to this vodeo
BRO THIS CONTENT IS PRIME! glad I found it before it cost money lol. Your amazing brother. Appreciate the content and the help! My new magic 3E is arriving tomorrow. Gonna be doing mapping and stockpile surveys I hope. Starting my own business is the idea. Keep it coming man.
I’m just here to see how to cost an inspection, does it cover that?
check this one out for that! kzread.info/dash/bejne/n213t7R9YNHIdLw.html
Is this support for air 2
Can´t wait.
Very nice video Sir, Could please share the name of Apk and Software used for Mapping for DJI Mini 3 Pro
It's Hammer Missions! The APK has not been released yet but we expect by May end this year
@@HammerMissions Noted with thanks Sir Hope to see the same Soon.
@@HammerMissionsHello Sir, Any Update regarding the Apk?.
@@HammerMissionsHello Sir, Any Update regarding the Apk,? please reply
@@mehulsolanki4526 Hi there, we have released the APK to select partners at the moment. We aim to bring it to everyone soon!
When is support for mini 3 coming and also air 2s?
We expect May 2024 for the Mini 3 Pro, no ETA for the Air2S at the moment.
I'm making building inspections professionally, traditional way, by walking, checking, making pictures, and your solution looks nice and easy, but results are, for technical evaluation, below expectations.... 1. The low resolution (because of distance of taking pictures do not allow to make accurate evaluation of degradation of particular parts especially, most important state of roof surface: cracks, possible leaks) 2. The game changer will be the possibility of making accurate measurements on this model (not on all directions, but on main surfaces of the building - along walls and roof) There are any solution of this issues? Probably when we will get better quality images the model will hang because of its size...
Hi there! thanks for your comments. Solutions exist! 1. You can always take close up pictures and simply add them to the dataset. 2. You can do that already: kzread.info/dash/bejne/p6eTy5mffq7Tc6Q.html You can add thousands of images to the project without worrying about the size and all works inside your web browser
Why was there no ground offset entered?
Well spotted! This mission should ideally use a ground offset, but since this was an inspection only mission and the post processing to make a map/model was not needed, getting exactly the overlap was less crucial.
When you added the images to the project, I noticed you only added the facade images from you folder. Do you then add the roof images into the same project folder?
That's correct, you would add the roof and facade images in the same project if your goal is to create a 3D model including both the roof and the facade.
*Promo sm* ✨
I’m using gcp’s for an interior map. Do I place the DJI RTK base station on say 3 of the GCP’s I’ve placed down? And if so, should I let the RTK gather data for say 15 minutes each?
Hi there! Yes, you should typically wait for the RTK / Base Station module to stabilise on each of the GCPs to note the correct positions. However, you might find that your true challenge is getting reliable GPS signal indoors!
No reason to use a 3e for mapping. In fact its got lesser camera quality youd be better off with a mini
what program you are using to map the roof??
It's Hammer Missions! hammermissions.com
Hello Varun, we've been trying to reach you for some facade inspection support. Please do let us know when's a good time to connect.
Would have liked to have seen a but more detail on how he went about making the field adjustments to the flight plan.
We'll do our next video just on that!
Does Hammer Missions work with the DJI Air2S?
Not at the moment but it's on the roadmap!
What software are u using?
Hammer Missions! hammermissions.com
Great video. Hope to be using Hammer Mission soon.
quality has nothing to do with (optimal) fly speed! the thing is does battery depletes exponentially faster with speed, so there is optimal speed for gaining maximum distance, camera or no camera
Hi there, if you fly faster than your camera can take photos, you will miss photos, which can affect the overall quality of the dataset, once processed. Hope this clarifies!
@@HammerMissionsi think i need to clarify -flying is flying and filming is filming, your video title talks about flying, not filming, not all drone flights are for content creation, duh
We always have a need on our jobsite to check elevation for say spoils haul off. We are currently using Drone Deploy with Emlid survey software to collect data for GCPs. It works well but it is time consuming for setup sometimes. You mentioned smart GCP's, I'm interested in looking into that workflow. Might save time and money! Has anyone on your team used the smart GCP method?
Hii, whats this software for mapping?
It's Hammer Missions! hammermissions.com
Wished i could afford the product... As a new Drone company the pricing is just far too much..
Hi! sorry to hear the pricing is not aligning with your business model. Are you sure you are pricing your clients correctly? We have a few videos on that which might be helpful: 1. kzread.info/dash/bejne/n213t7R9YNHIdLw.html&ab_channel=HammerMissions 2. kzread.info/dash/bejne/gpimyZiyn6WocZs.html&ab_channel=HammerMissions
How to not what it is the question was! @$%^^!
Hi there! 👋 Are you looking for a workflow video on how to measure stockpiles? This video might be helpful: kzread.info/dash/bejne/mXimzsSQfazgk5c.html
Yes, more flexibility in post-processing!! Retaining more color information is important. We dont want compressed detail 😉
Hi what a great video. I am interested in this type of work and equipment, could you give any advice on some one like my self a novice breaking onto this industry. I am able to fly a drone etc but where could i do courses for all of the survey work etc . Many thanks for your time. Kevin
Thank you for you kind words! We would recommend subscribing to our channel as we regularly post educational videos on drone survey & inspection related work. If you are looking to specifically break into magnetic surveying, we recommend speaking to Geometrics (magnetometer manufacturers) and looking into the mineral exploration industry. Good luck!
Great video
Thank you! 🙏
Costs 2 new P4RTKs (and spare batteries) can be purchased for the cost of one M3E or buy a P4RTK and a base station for same price. 20Mp cameras on both so I don't understand the comments that data quality is better with the M3E.
M3e has a 1 inch newer sensor as opposed to a micro 4/3 sensor on the phantom. The interval rate is faster with the mavic and it can pretty much finish the same amount of work in half the time.
In addition to the 2D map of the roof, can Hammer Missions generate a 2D ortho projections of the facades?
At the moment, you can only create a 3D model of the facades but 2D ortho is on the roadmap!
Excellent!
can this be done with a mavic 2 zoom?
Creating a 2D map? Yes!
Nice explanation thanks.
Thanks loving your content
Thank you! 🙏
can i use my mavic 2 pro
Yes you can! We recommend our Android app for the M2P
thanks, this is really useful
I'm new to drones and just purchased me an Autel evo 2 v3. I really like what you demonstrated and interested in using this program. Will this program be available to an Autel drone Aircraft? Also what do you mean by ground offset altitude? Great video, thanks in advance!
thanks for your kind words! We have autel on the roadmap but no release date as of yet
Sorry I didn’t catch what software You using there ?
It's Hammer Missions! hammermissions.com
Great video but I had to turn off, the background noise/music was making it uncomfortable to concentrate
Oh no! We'll try to lower / remove the background score in the next one!
(Message 1/2) Hello team, I liked your video, it accommodated my lack of understanding of some things regarding the three processing methods for geolocation of image sampling. I would like to ask you just 2 questions: 1.- IF you had to acquire equipment to make 2D/3D, orthomosaic/lever curves, points cloud, DEM models in mountains with forests, and smooth areas such as roads or old bridges to remodel ===> What equipment would you use? Was this team good? ==> M350 RTK, Zenmuse P1, Zenmuse L2 or PhaseOne IXM-100. 2.- Today the market is already equipped with many of these Mapping activities. With the equipment mentioned in point 1, it could make a difference in providing a higher quality service or it is not worth the effort to acquire this equipment because there are other processes. PPT that improves the quality of deliverables to the client. 3.- How could I match or get closer to the precision and results of the millimetric measurements of the millimetric equipment of traditional conventional surveyors? Could this PhaseOne IXM-100 40 MG pixel camera help or not? 4.- If I implement RTK, 3/4 of the time of surveying 200 hectares, my RTK GCP loses connectivity, could I continue surveying the sampling and then process everything with the PPK method? @sebastiandemuria4317 🤔
1 - There isn't a single absolute best equipment! We suggest reading our guide on how to buy the right drone: www.hammermissions.com/post/how-to-buy-drones 2 - It all starts with identifying a niche (small segment of the market) and serving that niche better than anybody else using your competitive advantages! 3 - Accuracy of the dataset has less to do with the camera and more to do with whether GCP/RTK/PPK was used. kzread.info/dash/bejne/l4Kr1Lp7pbDXiso.html 4 - Yes, one advantage of the PPK / GCP methods is that they are not real time method, so even if you lose connection, you can use to create higher accuracy outputs! Hope this helps!
@@HammerMissions Thanks for your prompt answers. 🙂
Message (2/2) 5.- Could you make a video with the differences between photometry and LiDAR? I understand the topic, but I would like to know more about where each one applies, I understand that LiDAR is better in forests, while photogrammetry is better on surfaces or to make orthomosaics It would be good to hear your experience on the subject. I am analyzing all this information to learn whether I could invest in a business that might offer a difference in the service outputs. Nowadays, many companies are providing this service, and I am wondering whether I can offer something better. Do you think this could be reached? Any comment would be awesome. Thanks for reading my comment. Kind regards. Sebastian
Ok you mention using survey grade equipment for positioning GCPs, then say later that it's a low up-front cost method
It's lower upfront cost as RTK drones or PPK software are not strictly required. It's more expensive in time spent layout the GCPs! 🏁
@@HammerMissions What's expensive is the GNSS receiver you need to accurately locate your GCPS-or the surveyor. Later you said you just put them down, but they are useless as ground control unless you have them accurately located. They are NOT low cost upfront. GCP targets: $100. GNSS receiver: $6K for our EOS Arrow. Emlid will get you cheaper.
@@JonWitsellPhotographicArts Our point was that all things being equal, they are lower cost than RTK or PPK methods as they do not require you to purchase an RTK drone, which at the time were typically higher priced than non-RTK drones. The cost for RTK drones has fallen sharply since and almost all new enterprise drones now have RTK enabled (yay!). And yes, we do recognise that the GNSS receiver can also be cost prohibitive! 👍
Could you perform calibration with the screen of the controller?
Not the vision one! You'll need the calibration board for that one 👍
Thank you for the great video, how many photos did you end up stitching for your model?
Thank you for the kind words! It was around 376 photos: kzread.info/dash/bejne/gH5okrOYitzfgMo.htmlfeature=shared&t=1080