mine CONTINOUSLY drips oil from reservoir. when you set it down when down oil will leak all over untie the tank is dry.
@boparker45788 күн бұрын
Thanks mon great video. I agree. What saw would you recommend for 10-24 inch firewood maybe 10-15 days a year …. Gas
@k9kayaksАй бұрын
Thanks for sharing. Took my Ryobi RY40508 part yesterday due to not oiling and found the nylon nut had the same issue on the threads. Admittedly I was doing cross cuts on a RedOak law back in January 🤷🏼♂️ Do you recommend a certain type of chain oil? I’ve seen where people say Ryobi Battery saws need a thinner oil. Again thank you for sharing ordering a couple “Oil Pump Drives” today 👍
@brthrgrimАй бұрын
Thanks for the video, I was able to fix my bar/chain oiler! It wasn't the worm gear, in my case, though I will buy one to have on hand. Rather, the hose from the oil pump to the port by the bar was not connected. Pretty puzzling, since I've never disassembled the saw before, and the hose was very secure once I put it on, no idea how it could come off in a mostly sealed compartment...
@shangriffin7219Ай бұрын
TJ, my msu 500 is stuck in low, and the fan gears are fine. Is this something you've dealt with before? I'd make the almost 4hr drive if you could fix for a fair price.
@LisaBlair-gn8otАй бұрын
Did you change the oil before installing the new parts? With how milky and nasty everything was on the gears I would assume that whatever is in the gearbox is in the same condition. I ordered the parts and then this question occurred to me hoping you can get a response to me sooner than later as the repair is waiting for your answer we trust you and really appreciate the videos!!
@tjssmallenginerepairАй бұрын
Yes, this customer also got a full tune up while doing this repair. I hope this all works out for you! Let me know how it turned out.
@janicewilder83532 ай бұрын
I have 2017 Mossimo 500 with 17 hrs on it. Issue is Mossimo 500 will not stay running unless the idle is high, but will not go in gear. Turn idle down, it will shift into gear, but will not stay running. Was in the shop for this issue, but they could not fix it. They tested all the fuel pressure, fuel filter, etc. all good. They said could be a vacuum pressure issue?????
@Charlie-wg2uc2 ай бұрын
Is it a spring loaded seal
@Charlie-wg2uc2 ай бұрын
Where can you get the o ring
@schnelkc3 ай бұрын
Excellent video…exactly what I needed. My worm gear was also shot. And yes, i pushed my saw beyond its limits. Parts are on the way! Thanks so much!
@tjssmallenginerepair3 ай бұрын
Glad the video was helpful to you!
@richardsoule2783 ай бұрын
Great job.
@colinblankenship24013 ай бұрын
Where is your shop? I need some work done on my Massimo 400 utv?
@timothyjohnson57584 ай бұрын
Sorry did not comment was visiting Grandma
@timothyjohnson57585 ай бұрын
HUSQVARNA IS THE WAY TO GO
@edslaney33756 ай бұрын
I had same problem on my Hisun 500 I haven’t been able to find the parts for it for over a year
@williamorton76007 ай бұрын
Thanks for the video, worked great and solved my issue. Is there a torque spec for those case bolts. I put them to 60 in-lbs for now. Mine had a lot of wear on that top seal...I'll have to do that in the future.
@michaelhagood95718 ай бұрын
Thanks man that video was great
@Bighotdog12348 ай бұрын
on the MSU 500 when the starter won't engage I am assuming its the starter clutch. Where exactly is it located on this model?
@reeba9999 ай бұрын
My dad bought one and the throttle is stuck wide open whenever you try to push the pedal no matter what gear your in. Got it from a dealership and they wouldnt help at all, any help would be greatly appreciated
@lonniebeaty3019 ай бұрын
Hey mine dies when shifted into reverse. Why?
@ramirobriones76909 ай бұрын
I have the same problem. Where are you located??
@joesantos39119 ай бұрын
Thank you. Great video.
@JGoulet97310 ай бұрын
Had same exact problem with my axis 500.. Only 13 miles on it and fan gears rusted right out.. Do you have the part #s for fan gears? Think you posted part #s but couldn’t read them.. Ty
@user-gp1dw3tp6q10 ай бұрын
I just bought a 2022 massimo 400. It's brand new. Never ridden. My question is it seems to have quite a bit of vibration from the handle bars is the normal. It's just sitting in park. Thanks
@usmcasmr99011 ай бұрын
Thanks for the info bud! Helped me out on my repair!
@haroldbeatty277411 ай бұрын
How about a video on changing fuel pump and fuel injector for MassimoMSU500 soon?
@wayneallen8211 ай бұрын
So glad they are enjoying it and thank you for all the great work you do.
@larrynorton9239 Жыл бұрын
My fan gears are bad where can I order them please help.
@tjssmallenginerepair Жыл бұрын
You can order them from Amazon. This link is to the ones that I bought previously. Haven't had an issue yet. www.amazon.com/gp/product/B08V97JZL5/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1#productDetails
@williamorton76007 ай бұрын
Got mine on amazon...Hisun 500. Fan Gears.
@RD-257 Жыл бұрын
I put an exhaust silencer on mine and it really helped with the loudness. kzread.info/dash/bejne/pGmZxNBunKuoY6g.html
@jakehenderson7960 Жыл бұрын
Great video learn a lot
@chuckconnors615 Жыл бұрын
What is part # for the coil pak??
@doncc6080 Жыл бұрын
Thanks. would that cause it to be stuck in reverse? I have a friend with Massimo who has that issue.
@tjssmallenginerepair Жыл бұрын
Very good possibility that could cause it. Not a difficult thing to check and see.
@MikeStJohn-yg7yh Жыл бұрын
Thank you for the video. Will be checking those fan gears. I have similar issues with some differences. Thanks again.
@maninifarmer1338 Жыл бұрын
Ivan get the gears to shift in and out. My problem is the indicator on the dash is always showing reverse. How do I fix this?
@tjssmallenginerepair Жыл бұрын
There could potentially be an issue with the cable that is grounded under one of the bolts. I'd check there first.
@user-sr5rw1dm9y Жыл бұрын
Where can you find the oil seal?
@tjssmallenginerepair Жыл бұрын
The part number I listed in the video is actually to a cub cadet machine, as they are identical seals. If you search the part number, there are plenty of aftermarket sites to aquire the seal.
@rodneywilliamson6048 Жыл бұрын
Great Video. I wished you would’ve showed how to get the oil seal out. They didn’t send it with the kit. I know how to but maybe you might have to better way. I hope you didn’t take that wrong. Thanks again for the video
@tjssmallenginerepair Жыл бұрын
I just used a flat head screw driver to pry it out. Make sure that when you do this that you note the depth of where the seal is seating in that cover. Then just use a socket that is almost the same size as the seal and tap it into place with a plastic hammer.
@rodneywilliamson6048 Жыл бұрын
Thanks for this video. Can you put some grease on the gears to help with friction. I noticed on mine there wasn’t any lubrication
@tjssmallenginerepair Жыл бұрын
Yes, you can put a light coating of grease onto it. However, there should be a port that goes from the engine into the shifter housing. Hence the seal and gaskets.
@rodneywilliamson6048 Жыл бұрын
@@tjssmallenginerepair is there is a port but no lubricant on the gears. I only had 32 hours on this machine. You can tell they didn’t put anything on the gears. I have replaced the clutch on this also!! The lubrication on these Hisun are Not good at all! Mine is a 2014 Coleman. I hope they have improved on this if they want to stay in business. Thanks again for your video
@rodneywilliamson6048 Жыл бұрын
@@tjssmallenginerepair yes that’s what I did I build and race cars and I knew what to do but some people may not know what to do. Keep your videos coming
@rodneywilliamson6048 Жыл бұрын
Nice video!! Just what I needed!! Thanks for the help. Keep your videos coming especially on the Hisun side x side.
Пікірлер
mine CONTINOUSLY drips oil from reservoir. when you set it down when down oil will leak all over untie the tank is dry.
Thanks mon great video. I agree. What saw would you recommend for 10-24 inch firewood maybe 10-15 days a year …. Gas
Thanks for sharing. Took my Ryobi RY40508 part yesterday due to not oiling and found the nylon nut had the same issue on the threads. Admittedly I was doing cross cuts on a RedOak law back in January 🤷🏼♂️ Do you recommend a certain type of chain oil? I’ve seen where people say Ryobi Battery saws need a thinner oil. Again thank you for sharing ordering a couple “Oil Pump Drives” today 👍
Thanks for the video, I was able to fix my bar/chain oiler! It wasn't the worm gear, in my case, though I will buy one to have on hand. Rather, the hose from the oil pump to the port by the bar was not connected. Pretty puzzling, since I've never disassembled the saw before, and the hose was very secure once I put it on, no idea how it could come off in a mostly sealed compartment...
TJ, my msu 500 is stuck in low, and the fan gears are fine. Is this something you've dealt with before? I'd make the almost 4hr drive if you could fix for a fair price.
Did you change the oil before installing the new parts? With how milky and nasty everything was on the gears I would assume that whatever is in the gearbox is in the same condition. I ordered the parts and then this question occurred to me hoping you can get a response to me sooner than later as the repair is waiting for your answer we trust you and really appreciate the videos!!
Yes, this customer also got a full tune up while doing this repair. I hope this all works out for you! Let me know how it turned out.
I have 2017 Mossimo 500 with 17 hrs on it. Issue is Mossimo 500 will not stay running unless the idle is high, but will not go in gear. Turn idle down, it will shift into gear, but will not stay running. Was in the shop for this issue, but they could not fix it. They tested all the fuel pressure, fuel filter, etc. all good. They said could be a vacuum pressure issue?????
Is it a spring loaded seal
Where can you get the o ring
Excellent video…exactly what I needed. My worm gear was also shot. And yes, i pushed my saw beyond its limits. Parts are on the way! Thanks so much!
Glad the video was helpful to you!
Great job.
Where is your shop? I need some work done on my Massimo 400 utv?
Sorry did not comment was visiting Grandma
HUSQVARNA IS THE WAY TO GO
I had same problem on my Hisun 500 I haven’t been able to find the parts for it for over a year
Thanks for the video, worked great and solved my issue. Is there a torque spec for those case bolts. I put them to 60 in-lbs for now. Mine had a lot of wear on that top seal...I'll have to do that in the future.
Thanks man that video was great
on the MSU 500 when the starter won't engage I am assuming its the starter clutch. Where exactly is it located on this model?
My dad bought one and the throttle is stuck wide open whenever you try to push the pedal no matter what gear your in. Got it from a dealership and they wouldnt help at all, any help would be greatly appreciated
Hey mine dies when shifted into reverse. Why?
I have the same problem. Where are you located??
Thank you. Great video.
Had same exact problem with my axis 500.. Only 13 miles on it and fan gears rusted right out.. Do you have the part #s for fan gears? Think you posted part #s but couldn’t read them.. Ty
I just bought a 2022 massimo 400. It's brand new. Never ridden. My question is it seems to have quite a bit of vibration from the handle bars is the normal. It's just sitting in park. Thanks
Thanks for the info bud! Helped me out on my repair!
How about a video on changing fuel pump and fuel injector for MassimoMSU500 soon?
So glad they are enjoying it and thank you for all the great work you do.
My fan gears are bad where can I order them please help.
You can order them from Amazon. This link is to the ones that I bought previously. Haven't had an issue yet. www.amazon.com/gp/product/B08V97JZL5/ref=ppx_yo_dt_b_search_asin_title?ie=UTF8&psc=1#productDetails
Got mine on amazon...Hisun 500. Fan Gears.
I put an exhaust silencer on mine and it really helped with the loudness. kzread.info/dash/bejne/pGmZxNBunKuoY6g.html
Great video learn a lot
What is part # for the coil pak??
Thanks. would that cause it to be stuck in reverse? I have a friend with Massimo who has that issue.
Very good possibility that could cause it. Not a difficult thing to check and see.
Thank you for the video. Will be checking those fan gears. I have similar issues with some differences. Thanks again.
Ivan get the gears to shift in and out. My problem is the indicator on the dash is always showing reverse. How do I fix this?
There could potentially be an issue with the cable that is grounded under one of the bolts. I'd check there first.
Where can you find the oil seal?
The part number I listed in the video is actually to a cub cadet machine, as they are identical seals. If you search the part number, there are plenty of aftermarket sites to aquire the seal.
Great Video. I wished you would’ve showed how to get the oil seal out. They didn’t send it with the kit. I know how to but maybe you might have to better way. I hope you didn’t take that wrong. Thanks again for the video
I just used a flat head screw driver to pry it out. Make sure that when you do this that you note the depth of where the seal is seating in that cover. Then just use a socket that is almost the same size as the seal and tap it into place with a plastic hammer.
Thanks for this video. Can you put some grease on the gears to help with friction. I noticed on mine there wasn’t any lubrication
Yes, you can put a light coating of grease onto it. However, there should be a port that goes from the engine into the shifter housing. Hence the seal and gaskets.
@@tjssmallenginerepair is there is a port but no lubricant on the gears. I only had 32 hours on this machine. You can tell they didn’t put anything on the gears. I have replaced the clutch on this also!! The lubrication on these Hisun are Not good at all! Mine is a 2014 Coleman. I hope they have improved on this if they want to stay in business. Thanks again for your video
@@tjssmallenginerepair yes that’s what I did I build and race cars and I knew what to do but some people may not know what to do. Keep your videos coming
Nice video!! Just what I needed!! Thanks for the help. Keep your videos coming especially on the Hisun side x side.
Glad it helped!