Пікірлер

• 
  @morrisart85Күн бұрын

  Did you ever get this sorted out? Maybe tried new pads?

• 
  @overkoatКүн бұрын

  @@morrisart85 hey man, unfortunately I sold the car BUT I did manage to get rid of most the noise with new pads. For the rear challenger pads fit. For the front Aston martin EBC pads fit

• 
  @garagenextdoor80725 күн бұрын

  This looks like a great alternative to spray guns, been researching for an hour and was wondering, can you use Single stage paint in this system with hardener and reducer? I'm doing a bodykit, small pieces and this would be a game changer this summer for me lol.

• 
  @overkoat24 күн бұрын

  @@garagenextdoor807 definitely! The main thing to do is make sure you clean the unit as soon as you’re finished. If you don’t, the hardener will end up solidifying the paint inside and render the power system useless for the next Job

• 
  @beausmith0827 күн бұрын

  I love these little things! So much better than aerosol cans. I wish I would’ve known about them before. Only thing I didn’t realize is the charger runs out. I had to get a ride to buy more lol.

• 
  @overkoat24 күн бұрын

  @@beausmith08 home depot is the USA is the cheapest place to find them!

• 
  @nrw1344Ай бұрын

  Great Vid.! This is probably a dumb question however I am rookie as they come to painting…is this product using the same solvents as a rattle can spray paint.? Will it be oil based paint once sprayed.? Or is this simply compressed air? I just dont want to ruin my paint.. im using a water base paint…

• 
  @overkoatАй бұрын

  Not a dumb question at all! The Preval sprayer uses an eco-friendly propellant and can be used with a variety of solvents, including: Water, Acetone, Mineral spirits, Lacquer thinner, and 2K solvents. The Preval sprayer can be used with many liquids, including paint, adhesive, gel coats, and PVA. It can spray water-based, latex-based, and oil-based paints, as well as acrylics, alkyds, clear coats, enamels, epoxys, lacquers, leather dyes, polyurethanes, primers, rust inhibitors, stains, varnishes, and waterproofers

• 
  @nrw1344Ай бұрын

  @@overkoatNice.! I am going to give this a try then… im using a highly pearlescent acrylic so i just didnt want to ruin it thanks a ton.!.!

• 
  @EvenMoreFreedomDotComАй бұрын

  Great video, thank you

• 
  @suspensefulness2 ай бұрын

  is raail easier than flex or halo efx

• 
  @overkoat2 ай бұрын

  Personally I find them very similar when spraying. It’s the top coat that gets complicated

• 
  @suspensefulness2 ай бұрын

  @@overkoat any advice, i painted cars before with 2k clear coats , do all three require alot of base coats to be peelable,

• 
  @suspensefulness2 ай бұрын

  @@overkoat hard to really find newer videos on all three , i actually like this over vinyl wrap ,just gotta find the best option thanx for responding

• 
  @overkoat2 ай бұрын

  @@suspensefulness yes to be on the safe side, I go by gallons. To make sure everything is peel able, I use around 6 gallons of base and color for a midsized sedan/ coupe before I spray the 2k clear

• 
  @overkoat2 ай бұрын

  @@suspensefulness follow me on IG @overkoat and i’ll put you on to what exactly I use

• 
  @suspensefulness2 ай бұрын

  nice nice setup...question...raail vs halo efx and autoflex which do u prefer

• 
  @overkoat2 ай бұрын

  For my personal use, I found the halo efx is the most cost effect and versatile. You can top halo with tamco 4100 for professional mirror finish or dip armor for a satin sheen.

• 
  @ChristopherBristol2 ай бұрын

  Hey on those rear the pads with the indent on it is for what I assume is brake pad wear sensors.

• 
  @stephencavanaugh83772 ай бұрын

  What city do I need to avoid driving in, so I don't risk my safety, with you on the road with this crap on your car?

• 
  @overkoat2 ай бұрын

  New York. Stay away from New York please and thanks.

• 
  @JB-zb9zo2 ай бұрын

  Brave

• 
  @mrbkkt12 ай бұрын

  trusting in chineseum to stop is very brave.

• 
  @DaTT782 ай бұрын

  ...but how do they feel? 🤣

• 
  @overkoat2 ай бұрын

  😂😂😂😂🤣🤣🤣

• 
  @HappyPel2 ай бұрын

  I would double check that everything is torqued down in the back. I also would bleed them again. When you broke them in, did you engage ABS and get to the point of making them smell several times?

• 
  @overkoat2 ай бұрын

  Thanks man! I just swapped out the rear with some powerstop z26’s. So far, majority if the sound is gone. I’m just waiting on my front pads

• 
  @imDnice2 ай бұрын

  Did you break them in?

• 
  @overkoat2 ай бұрын

  Yup they were broken in unfortunately

• 
  @johndominguez12462 ай бұрын

  Yoo! Do you have an ig?

• 
  @overkoat2 ай бұрын

  @@johndominguez1246 @overkoat

• 
  @drewmurray25832 ай бұрын

  where is our money going?

• 
  @tonymuthafuckingunn2 ай бұрын

  I've had a set of Ksports that looks just like this on my car for 12 years. They've seen the track, been put through the paces and still ticking. Aluminum is Aluminum. All manufactures usually paint over the bolts, and the ones that don't have powdercoat come off so you can change you're brake pads from the top without taking the whole caliper off. I'd say maybe get some safety wire, but otherwise, enjoy em!

• 
  @IntheBay852 ай бұрын

  Beautiful cats!

• 
  @overkoat2 ай бұрын

  Thanks so much! I love them

• 
  @jasonbagnall42412 ай бұрын

  There is nothing wrong with those brakes, and assuming they aren't out of spec, those will stop your car very fast! Those are opppossed piston commercial brakes used on towing winches, cars, trucks and similar. The cross-over brake lines are to allow you to plumb the lines in the most convient method!The squiggly milled rotors keep the pads from glazing. Cross-drilling was never about cooling, but squiggly milling with an end mill does the same thing. If the rotors are semi-floating or full-floating as they apppear to be, that allows the rotors to expand and contract without warpage!

• 
  @overkoat2 ай бұрын

  That’s great to know! I really do hope they hold up

• 
  @jonnymiskatonic2 ай бұрын

  brakes from Alibaba =D You got more balls than I do for sure. Good luck.

• 
  @overkoat2 ай бұрын

  😂😂😂😂 hopefully everyone who’s thinking of these learns from this series

• 
  @MikeZ32TT2 ай бұрын

  Interesting

• 
  @quarterblacktravis2 ай бұрын

  Hahah that's not cheap. Cheap is real brembos from a cali fir 200 a pair.

• 
  @overkoat2 ай бұрын

  😂😂😂 you’re definitely right! This is for those who aren’t lucky enough to find a set that “fell off the truck” lol

• 
  @quarterblacktravis2 ай бұрын

  @overkoat nope didn't fall off a truck. They come stock on Cadillacs I bought a set new off Amazon for 110 each side. And put them on my foxbody. They fit on alot of cars

• 
  @quarterblacktravis2 ай бұрын

  @overkoat there is alot of videos on KZread they swap them o. Everything and they are made I the USA. Look up foxbody cadi brakes. Your welcome

• 
  @overkoat2 ай бұрын

  Seriously?? I wish I found out about them sooner

• 
  @quarterblacktravis2 ай бұрын

  @@overkoat get a set now just because before everyone makes them expensive

• 
  @HappyPel2 ай бұрын

  Those look pretty solid. How much were they? I hope they work for you and don't fall into little pieces as you are driving.

• 
  @overkoat2 ай бұрын

  Lets hope so! They were $1450 shipped to my door. I’m driving them hard “pause” and i’m already noticing a few things i’ll definitely update everyone on

• 
  @HappyPel2 ай бұрын

  @@overkoat Ya that is alot cheaper than most BBKs. They kind of look like Brembo clones, is that what they are? Very interested in what they are doing well in and what they are doing poorly in.

• 
  @overkoat2 ай бұрын

  @@HappyPel after a week of heavy spirited driving, I have a huge noise issue with them. I’m going to make a vid about it

• 
  @Group_Anonymous2 ай бұрын

  Blah blah blah bring back cat 🐈

• 
  @overkoat2 ай бұрын

  Those are my children 🥹

• 
  @lewis35892 ай бұрын

  Honestly it’s a W if you can get it in ok condition for the price

• 
  @overkoat2 ай бұрын

  Definitely!

• 
  @Graphic_vq.r2 ай бұрын

  Cool video, ain’t nothing wrong with going a different path

• 
  @overkoat2 ай бұрын

  Thanks man, So far they seem like a extremely good deal.

• 
  @amgrealyfe2 ай бұрын

  What’s the link to buy these?

• 
  @overkoat2 ай бұрын

  It’s actually a direct phone number to the supplier. Stay tuned. if everything goes smoothly this week, I’ll let you know. Don’t want to send you a bad product and info

• 
  @Kayobear192 ай бұрын

  Looks very lame on the coupe. Its a coupe !

• 
  @roguescollective3 ай бұрын

  Great Job!!!

• 
  @guerotech2 жыл бұрын

  Some people really know how to ruin a nice car.

• 
  @SpiritedWrenchers2 жыл бұрын

  Thanks for sharing. I really like the look of it. We're resto -modding a 70 coupe on our channel and I'm just not a fan of the spoiler that goes with them so this is a viable option to help with the stance and look.

• 
  @overkoat2 жыл бұрын

  Thanks so much!! I hope that you could make it work even better than I have on your build if you go this route! I’m definitely subscribing to follow your build

• 
  @SpiritedWrenchers2 жыл бұрын

  @@overkoat you're welcome. Thank you for subscribing and following along. We look forward to chatting more as we work through it.

• 
  @stallionranchwoodworks3 жыл бұрын

  I think it would look much better installing it like it should be. Just my .02 worth.

• 
  @overkoat3 жыл бұрын

  Honestly, I would actually like to see how it would have looked installed the correct direction. If I get my hands on another trunk lid, I would definitely do it again.

• 
  @stallionranchwoodworks3 жыл бұрын

  @@overkoat watch this video of a Mustang down in Mexico. kzread.info/dash/bejne/Zn9nmZurnLypg6Q.html

• 
  @stallionranchwoodworks3 жыл бұрын

  @@overkoat here is another, kzread.info/dash/bejne/poWNt5Z7ZpCdecY.html

• 
  @SkitzV3 жыл бұрын

  dude this is awesome ! so are you just shooting spherical as a PPF with a bunch of coats or are you doing some coats of clear base first ?

• 
  @overkoat3 жыл бұрын

  Thanks man! I’m shooting a few coats of base first, then 2 coats of spherical

• 
  @timothycoone83883 жыл бұрын

  Wow looks great this will work perfect for my 69

• 
  @elcartelframing3 жыл бұрын

  I added the Shelby rear spoiler on my 70 coupe

• 
  @SpiritedWrenchers2 жыл бұрын

  Thanks for posting that. I was curious about it myself. Which one did you pick up? Link?

• 
  @jamesjakubik44283 жыл бұрын

  Great idea !

• 
  @overkoat3 жыл бұрын

  Appreciate it bud!

• 
  @LypheusX3 жыл бұрын

  Wow, this took courage man - congrats! Love the ingenuity and thinking outside the box on this one :)

• 
  @overkoat3 жыл бұрын

  I truly appreciate the kind words! I’m hoping that someone can take this and make something amazing!

• 
  @Aceboogie23863 жыл бұрын

  Looking good

• 
  @overkoat3 жыл бұрын

  Appreciate it bud!

• 
  @roguescollective3 жыл бұрын

  Looks amazing !!

• 
  @overkoat3 жыл бұрын

  Thank you so much 😁

• 
  @edwinj82753 жыл бұрын

  I’m glad someone tried this, I’ve been wanting to do so for a while

• 
  @overkoat3 жыл бұрын

  I can’t take all of the credit. I’ve seen people do this before. Just no one else never documented their process lol